COMPONENT SPECIFICATIONS 49990-xxx 49800-xxx
Fast-Cure® Anaerobic Adhesive-Style Connectors
Leviton’s Fast-Cure anaerobic adhesive-style connectors are designed for quick and easy termination in the field. Fast-Cure connectors are available in singlemode and multimode versions in ST®, SC, FC, and LC styles. Fast-Cure connectors are designed for indoor and outdoor applications where reliability, durability, and ease of installation are an important consideration. Typical installations are in premise LAN environments, or anywhere adhesive-style connectors are specified.
FEATURES • • • • • •
Typical termination in less than two minutes Low insertion loss connection Higher fiber retention than mechanical connectors No curing oven or proprietary tool required Compatible with MOS, QuickPort®, Opt-X®, and LightSpace® adapter plates Accessory for duplex clip sold separately
DESIGN CONSIDERATIONS • • • • • •
Single-mode and multimode versions Precision pre-radiused zirconia ferrules Supports 900 µm buffered fiber or 3 mm jacketed fiber High cable retention crimp for jacketed fiber Recommended for indoor and outdoor usage Body of ST and FC connectors are metal
PERFORMANCE SPECIFICATIONS Pictured (left to right): ST Connector, SC Connector, FC Connector, and LC Connector.
SPECIFICATION
The Fast-Cure anaerobic adhesive-style fiber optic connector shall meet or exceed the requirements described in TIA-568-C.3 and 604 standards. Connector shall be field-polished, field-installable, and does not require a curing oven or proprietary tool to facilitate the termination of the fiber. Connector shall be available in LC, SC, FC or ST, single-mode or multimode configurations terminated on 900 µm buffered fiber or 3 mm jacketed fiber. Typical connector Insertion Loss shall be 0.2dB. Typical connector Return Loss shall be greater than 25dB (multimode) and 55dB (single-mode).
Parameter
Value
Insertion Loss (Single-mode or Multimode)
Typical: 0.2dB Max: 55dB
Return Loss (Multimode)
Typical: >25dB
Operating Temperature
-40 ºC to +85 ºC
STANDARDS COMPLIANCE
• Meets TIA-568-C.3 performance requirements • Meets TIA-604-2 (ST), -3 (SC), -4 (FC), -10A (LC) Connector Intermateability Standards • Meets GR-326; General Requirement for Single-mode Connectors
WARRANTY INFORMATION
For a copy of Leviton product warranties, visit www.leviton.com.
Page 1 of 2
Leviton Network Solutions, a division of Leviton Mfg. Co., Inc. 2222 - 222nd St. SE Bothell, WA 98021 Tech Support: 1.800.722.2082 or +1.425.486.2222 Fax: 1.425.485.9170 www.leviton.com Copyright © 2010 Leviton Manufacturing Co., Inc. All rights reserved. Subject to change without notice.
49990-xxx 49800-xxx
APPLICATION
FC
COMPONENT SPECIFICATIONS 49990-xxx 49800-xxx FC 1.41"
ST ST
1.41"
2.35"2.35" .38"
.38"
ELECTRONIC FILES .39"
2.35" ST FC .39" 1.47" visit .56" For CAD files, typical specs, or dimensional line art (.DXF, .DWG, Visio), www.leviton.com. 1.41"
FC
LC
.39" .39" .39" .38"
.39"1.58" .70" .39"
LC .38"
2.29" .50"
1.58" 1.58" .50"
.50" 1.58" .50" .10" 1.58"
.10"
.38"
SC
.38"
1.47" .60"
.32"
SC
.37" 1.93"
.05"
[1.25 mm]
.60"
[2.5 mm] .10" [2.5 mm]
.10"
.38" .60"
.10" .10" .60" [2.5 mm]
.56"
.60" .56"
.56" .10" .10"
.56"
[2.5 mm]
[2.5 mm]
.10"
.56"
1.48"
SC
.10"
[2.5 mm]
1.48" .10" [2.5 mm] .10" [2.5 mm]
1.48" .60"
2.53"
[2.5 mm]
[2.5 mm] .10" [2.5 mm] [2.5 mm]
.10" [2.5 mm]
[2.5 mm]
Fast-Cure SC Connector
SC
2.53"
Side View, w/ 3 mm boot.10" Front .32" .32" [2.5View mm] .32" .60" .32" .10" [2.5 mm] .32" 1.82" 2.53" .10" [2.5 mm] .56" 2.53" [2.5 mm] .10" .32" [2.5 mm] 2.53" .10" 2.53" [2.5 mm] .10" .32" [2.5 mm] .10" 2.53" Side View, w/ 900 µm boot [2.5 mm] .10"
1.82"
.32" .32" .32" .32"
2.53"
.37" 1.26" .37"
.56" .56"
.38"
.32" .37"
.10"
.56" .60" 1.48" Side µm boot .38" View, w/ 900 1.48" .10" 1.48" .56"
.38" .56"
1.47"
.38"
.38" 1.93".50" 1.58" .38" mm] [1.25 mm] .10" [2.5.05" .38" .37" 1.93" .38" 1.93" SC [1.25mm] mm] 1.93" .05" [1.25 .05" 1.93" [1.25 mm] .05" Side View, w/ 9001.26" µm boot [1.25 mm] [1.25 mm] .05" .05" 1.93" [1.25 mm] .05" .37" .32"
.38"
.56" 1.47" .56"
1.47"
.38"
SC
[2.5 mm]
2.35"
2.35"
SC .32"
.10"
1.48"
1.47"
[2.5 mm]
[2.5 mm]
2.35" Fast-Cure ST® Connector 2.35" 2.35" Side View, w/ 3 mm boot Front View .56" 1.47"
.38" .38"
SC
.10"
1.48"
.38"
ST
.38"
LC
.56"
1.47"
ST .38" .38"
[1.25 mm] .05" Front View
SideLC View, w/ 3 mm boot
.39"
ST ST
.50" .10" [2.5 mm] [2.5 mm] .10" [2.5 mm] .10" [2.5 mm] .50" .10" [2.5 mm]
LC 2.29"LC 1.93" LC Fast-Cure LC Connector
.38"
.10"
1.82" 1.82" 1.82"
1.82"
.10"
.10" .10" 1.82" [2.5 mm]
[2.5 mm] [2.5 mm] .10" [2.5 mm] .10" [2.5 mm] [2.5 mm]
LEVITON FAST-CURE CONNECTORS .10" [2.5 mm]
.37"
1.26" .05" [1.25 mm] [1.25 mm] .05" 1.26" 1.26" 1.26" [1.25 mm] .05" [1.25 mm] .05" [1.25 LEVITON TOOLKITS & ACCESSORIES mm] .05" 1.26" Description Part [1.25No. mm] .05"
Description
Part No.
® .32" Fast-Cure ST Multimode
49990-MST
Fast-Cure ST Single-mode
49990-SST
49800-MTK
Fast-Cure SC Multimode, .10"beige [2.5 mm]
49990-MSC
49800-FTK
Fast-Cure SC LOMM, aqua
49990-LSC
49800-CON
Fast-Cure SC Single-mode, blue
49990-SSC
49886-DSC
Fast-Cure LC Multimode, beige w/ 3 mm boot
49990-ML2
LC Duplex Clip, beige, MM (bag of 25)
49886-DLM
Fast-Cure LC LOMM, aqua w/ 3 mm boot
49990-LL2
LC Duplex Clip, blue, SM (bag of 25)
49886-DLS
Fast-Cure LC Multimode, beige w/ 900 um boot
49990-MDL
Fast-Cure LC LOMM, aqua w/ 900 mm boot
49990-LDL
Fast-Cure LC Single-mode, blue w/ 3 mm boot
49990-SL2
Fast-Cure LC Single-mode, blue w/ 900 um boot
49990-SDL
Fast-Cure FC Multimode
49990-MFC
Fast-Cure FC Single-mode
49990-SFC
Light Tool Kit .37"Fast-Cure Tool Kit
Consumable Kit SC Duplex1.26" Clip, black (bag of 25) .05"
[1.25 mm]
1.82"
NOTE: Both single-mode and multimode SC, ST, and FC connectors come with a 3 mm and 900 µm boot. ST is a registered trademark of AT&T Inc.
Page 2 of 2
H/10 #3471
Leviton Network Solutions, a division of Leviton Mfg. Co., Inc. 2222 - 222nd St. SE Bothell, WA 98021 Tech Support: 1.800.722.2082 or +1.425.486.2222 Fax: 1.425.485.9170 www.leviton.com Copyright © 2010 Leviton Manufacturing Co., Inc. All rights reserved. Subject to change without notice.
49990-xxx 49800-xxx
.39"
.70" Fast-Cure FC Connector .10" [2.5 mm] FC .70" .39" 1.41" [2.5 mm] FCw/ 3 mm.50" Side View, boot .10" Front View FC 1.41" .50" 2.29" 1.41" FC.39" .70" 1.41" .39" 2.29" .10" [2.5 mm] .39" .39" .50" .70" .39" .70" .10" [2.5 mm] 1.58" 2.29" .70".50" .50" .10" [2.5 mm] .10" [2.5 mm] .50" .10" [2.5 mm] .70" Side View, w/ 900 µm boot .50" ST 1.58" .50"2.29" .10" [2.5 mm] 1.41" .39" 2.29".10" .50" [2.5 mm] LC 2.29"
COMPONENT SPECIFICATIONS 49990-xxx 49800-xxx
Fast-Cure® Anaerobic Adhesive-Style Connectors
Leviton’s Fast-Cure anaerobic adhesive-style connectors are designed for quick and easy termination in the field. Fast-Cure connectors are available in singlemode and multimode versions in ST®, SC, FC, and LC styles. Fast-Cure connectors are designed for indoor and outdoor applications where reliability, durability, and ease of installation are an important consideration. Typical installations are in premise LAN environments, or anywhere adhesive-style connectors are specified.
FEATURES • • • • • •
Typical termination in less than two minutes Low insertion loss connection Higher fiber retention than mechanical connectors No curing oven or proprietary tool required Compatible with MOS, QuickPort®, Opt-X®, and LightSpace® adapter plates Accessory for duplex clip sold separately
DESIGN CONSIDERATIONS • • • • • •
Single-mode and multimode versions Precision pre-radiused zirconia ferrules Supports 900 µm buffered fiber or 3 mm jacketed fiber High cable retention crimp for jacketed fiber Recommended for indoor and outdoor usage Body of ST and FC connectors are metal
PERFORMANCE SPECIFICATIONS Pictured (left to right): ST Connector, SC Connector, FC Connector, and LC Connector.
SPECIFICATION
The Fast-Cure anaerobic adhesive-style fiber optic connector shall meet or exceed the requirements described in TIA-568-C.3 and 604 standards. Connector shall be field-polished, field-installable, and does not require a curing oven or proprietary tool to facilitate the termination of the fiber. Connector shall be available in LC, SC, FC or ST, single-mode or multimode configurations terminated on 900 µm buffered fiber or 3 mm jacketed fiber. Typical connector Insertion Loss shall be 0.2dB. Typical connector Return Loss shall be greater than 25dB (multimode) and 55dB (single-mode).
Parameter
Value
Insertion Loss (Single-mode or Multimode)
Typical: 0.2dB Max: 55dB
Return Loss (Multimode)
Typical: >25dB
Operating Temperature
-40 ºC to +85 ºC
STANDARDS COMPLIANCE
• Meets TIA-568-C.3 performance requirements • Meets TIA-604-2 (ST), -3 (SC), -4 (FC), -10A (LC) Connector Intermateability Standards • Meets GR-326; General Requirement for Single-mode Connectors
WARRANTY INFORMATION
For a copy of Leviton product warranties, visit www.leviton.com.
Page 1 of 2
Leviton Network Solutions, a division of Leviton Mfg. Co., Inc. 2222 - 222nd St. SE Bothell, WA 98021 Tech Support: 1.800.722.2082 or +1.425.486.2222 Fax: 1.425.485.9170 www.leviton.com Copyright © 2010 Leviton Manufacturing Co., Inc. All rights reserved. Subject to change without notice.
49990-xxx 49800-xxx
APPLICATION
FC
COMPONENT SPECIFICATIONS 49990-xxx 49800-xxx FC 1.41"
ST ST
1.41"
2.35"2.35" .38"
.38"
ELECTRONIC FILES .39"
2.35" ST FC .39" 1.47" visit .56" For CAD files, typical specs, or dimensional line art (.DXF, .DWG, Visio), www.leviton.com. 1.41"
FC
LC
.39" .39" .39" .38"
.39"1.58" .70" .39"
LC .38"
2.29" .50"
1.58" 1.58" .50"
.50" 1.58" .50" .10" 1.58"
.10"
.38"
SC
.38"
1.47" .60"
.32"
SC
.37" 1.93"
.05"
[1.25 mm]
.60"
[2.5 mm] .10" [2.5 mm]
.10"
.38" .60"
.10" .10" .60" [2.5 mm]
.56"
.60" .56"
.56" .10" .10"
.56"
[2.5 mm]
[2.5 mm]
.10"
.56"
1.48"
SC
.10"
[2.5 mm]
1.48" .10" [2.5 mm] .10" [2.5 mm]
1.48" .60"
2.53"
[2.5 mm]
[2.5 mm] .10" [2.5 mm] [2.5 mm]
.10" [2.5 mm]
[2.5 mm]
Fast-Cure SC Connector
SC
2.53"
Side View, w/ 3 mm boot.10" Front .32" .32" [2.5View mm] .32" .60" .32" .10" [2.5 mm] .32" 1.82" 2.53" .10" [2.5 mm] .56" 2.53" [2.5 mm] .10" .32" [2.5 mm] 2.53" .10" 2.53" [2.5 mm] .10" .32" [2.5 mm] .10" 2.53" Side View, w/ 900 µm boot [2.5 mm] .10"
1.82"
.32" .32" .32" .32"
2.53"
.37" 1.26" .37"
.56" .56"
.38"
.32" .37"
.10"
.56" .60" 1.48" Side µm boot .38" View, w/ 900 1.48" .10" 1.48" .56"
.38" .56"
1.47"
.38"
.38" 1.93".50" 1.58" .38" mm] [1.25 mm] .10" [2.5.05" .38" .37" 1.93" .38" 1.93" SC [1.25mm] mm] 1.93" .05" [1.25 .05" 1.93" [1.25 mm] .05" Side View, w/ 9001.26" µm boot [1.25 mm] [1.25 mm] .05" .05" 1.93" [1.25 mm] .05" .37" .32"
.38"
.56" 1.47" .56"
1.47"
.38"
SC
[2.5 mm]
2.35"
2.35"
SC .32"
.10"
1.48"
1.47"
[2.5 mm]
[2.5 mm]
2.35" Fast-Cure ST® Connector 2.35" 2.35" Side View, w/ 3 mm boot Front View .56" 1.47"
.38" .38"
SC
.10"
1.48"
.38"
ST
.38"
LC
.56"
1.47"
ST .38" .38"
[1.25 mm] .05" Front View
SideLC View, w/ 3 mm boot
.39"
ST ST
.50" .10" [2.5 mm] [2.5 mm] .10" [2.5 mm] .10" [2.5 mm] .50" .10" [2.5 mm]
LC 2.29"LC 1.93" LC Fast-Cure LC Connector
.38"
.10"
1.82" 1.82" 1.82"
1.82"
.10"
.10" .10" 1.82" [2.5 mm]
[2.5 mm] [2.5 mm] .10" [2.5 mm] .10" [2.5 mm] [2.5 mm]
LEVITON FAST-CURE CONNECTORS .10" [2.5 mm]
.37"
1.26" .05" [1.25 mm] [1.25 mm] .05" 1.26" 1.26" 1.26" [1.25 mm] .05" [1.25 mm] .05" [1.25 LEVITON TOOLKITS & ACCESSORIES mm] .05" 1.26" Description Part [1.25No. mm] .05"
Description
Part No.
® .32" Fast-Cure ST Multimode
49990-MST
Fast-Cure ST Single-mode
49990-SST
49800-MTK
Fast-Cure SC Multimode, .10"beige [2.5 mm]
49990-MSC
49800-FTK
Fast-Cure SC LOMM, aqua
49990-LSC
49800-CON
Fast-Cure SC Single-mode, blue
49990-SSC
49886-DSC
Fast-Cure LC Multimode, beige w/ 3 mm boot
49990-ML2
LC Duplex Clip, beige, MM (bag of 25)
49886-DLM
Fast-Cure LC LOMM, aqua w/ 3 mm boot
49990-LL2
LC Duplex Clip, blue, SM (bag of 25)
49886-DLS
Fast-Cure LC Multimode, beige w/ 900 um boot
49990-MDL
Fast-Cure LC LOMM, aqua w/ 900 mm boot
49990-LDL
Fast-Cure LC Single-mode, blue w/ 3 mm boot
49990-SL2
Fast-Cure LC Single-mode, blue w/ 900 um boot
49990-SDL
Fast-Cure FC Multimode
49990-MFC
Fast-Cure FC Single-mode
49990-SFC
Light Tool Kit .37"Fast-Cure Tool Kit
Consumable Kit SC Duplex1.26" Clip, black (bag of 25) .05"
[1.25 mm]
1.82"
NOTE: Both single-mode and multimode SC, ST, and FC connectors come with a 3 mm and 900 µm boot. ST is a registered trademark of AT&T Inc.
Page 2 of 2
H/10 #3471
Leviton Network Solutions, a division of Leviton Mfg. Co., Inc. 2222 - 222nd St. SE Bothell, WA 98021 Tech Support: 1.800.722.2082 or +1.425.486.2222 Fax: 1.425.485.9170 www.leviton.com Copyright © 2010 Leviton Manufacturing Co., Inc. All rights reserved. Subject to change without notice.
49990-xxx 49800-xxx
.39"
.70" Fast-Cure FC Connector .10" [2.5 mm] FC .70" .39" 1.41" [2.5 mm] FCw/ 3 mm.50" Side View, boot .10" Front View FC 1.41" .50" 2.29" 1.41" FC.39" .70" 1.41" .39" 2.29" .10" [2.5 mm] .39" .39" .50" .70" .39" .70" .10" [2.5 mm] 1.58" 2.29" .70".50" .50" .10" [2.5 mm] .10" [2.5 mm] .50" .10" [2.5 mm] .70" Side View, w/ 900 µm boot .50" ST 1.58" .50"2.29" .10" [2.5 mm] 1.41" .39" 2.29".10" .50" [2.5 mm] LC 2.29"
4999X-XST 49800-XMK
Leviton FastCAMTM ST Connectors Connecteurs FastCAM MC ST de Leviton Conectores FastCamMR ST de Leviton
Instructions for Use
Directives d’utilisation
Instrucciones de uso
Leviton FastCAM ST Connector Termination
Terminaison des connecteurs FastCAM ST de Leviton
Conectores FastCamMR ST de Leviton
This instruction sheet describes the assembly procedure for applying Leviton FastCAM ST optical connectors. Please be sure to read this instruction sheet carefully before applying the connector. SAFETY PRECAUTIONS: Always wear eye protection when handling optical fibers. Properly dispose of any cut or cleaved ends.
Le présent feuillet de directives décrit la procédure d’assemblage des connecteurs optiques FastCAM ST de Leviton. Prière de le lire attentivement avant de procéder. CONSIGNES DE SÉCURITÉ : il faut toujours porter des lunettes de sécurité lorsqu’on manipule des fibres optiques. Les bouts coupés ou clivés doivent en outre être éliminés de la manière appropriée.
Esta hoja de instrucciones describe el proceso de ensamblado para los conectores de fibra óptica FastCam ST de Leviton. Lea estas instrucciones detalladamente antes de armar el conector. PRECAUCIONES DE SEGURIDAD: Siempre utilice gafas protectoras cuando trabaje con fibra óptica. Deseche apropiadamente todos los pedazos de fibra.
See reverse for corresponding illustrations. 1. Wedge is engaged at shipment. If it has become dislodged, squeeze the top and bottom insuring the wedge is inserted into the connector body. A click will be heard. 2. If using 900µm buffered fiber, remove the protection tubing from the boot. Slide it out the front of the boot. Slide the boot onto the fiber, small end first. 3.
Strip the fiber, removing the buffer coating, leaving the fiber longer than the finished cleave length (see Figure 1). It is recommended to clean the fiber with an alcohol wipe between the strip and cleave steps to remove any dust or debris.
Housing Coquille Caja
Connector Main Body Corps Cuerpo del Conector
Dust Cap Capuchon pare-poussière Tapa
Boot Manchon Bota
1. Pour l’expédition, la clé de came a été enclenchée sur le corps du connecteur; si elle s’en est délogée, la serrer verticalement afin de la mettre en place (un déclic doit se faire entendre).
1. La cuña está instalada durante el envío. Si se desengancha, presione la parte superior e inferior para insertarla nuevamente en el cuerpo del conector; escuchará un “clic”.
2. En présence de fibre isolée de 900 µm, retirer le tube protecteur du manchon en le glissant vers l’avant. Insérer le manchon sur la fibre, la plus petite extrémité en premier. 3.
Dénuder la fibre, en retirant la gaine sur une section plus longue que le segment de clivage (figure 1). On recommande de nettoyer la fibre au moyen d’un tampon d’alcool entre les étapes de dégainage et de clivage afin d’éliminer la poussière ou les débris accumulés.
4. Pour s’assurer que la fibre n’ait pas été endommagée à l’étape du dégainage, en vérifier l’intégrité en recourbant légèrement la partie dénudée.
5.
5.
Strip 13mm of buffer/coating from the 900µm fiber, or 10mm of buffer/coating from the 250µm fiber. On the 900µm fiber, make a mark at 11mm. On the 250µm fiber, make a mark at 14mm (see Figure 1). Proceed with cleaving per cleave tool instructions.
Note: Due to typical mechanical stripping of tight-buffered 900µm fiber, a small portion of 250µm coating may remain. This must be maintained to a maximum length of 3mm.
6. Insert the cleaved fiber into the rear of the connector. Carefully guide the fiber into connector body opening. 7.
Hold the fiber approximately 40-60 mm (1.57-2.35 in) behind the connector and maintain a slight force and bend on the fiber. This insures the prepared fiber is against the internal fiber. Your mark on the fiber should be hidden inside the connector body.
8. Maintaining the slight force on the fiber, release the wedge clip by squeezing it from the side. 9. Swing the locking piece from the bottom of the wedge unit and remove the wedge from the connector assembly.
Retirer 13 mm de gaine/revêtement de la fibre de 900 µm, ou 10 mm en présence de fibre de 250 µm. Dans le premier cas (900 µm), marquer la fibre isolée à 11 mm, et dans le second (250 µm), à 14 mm (figure 1). Cliver suivant les directives accompagnant l’outil.
A. On recommande d’employer l’outil de clivage Fujikura CT-30A* en présence de connecteurs FastCAM monomodes ou multimodes compris dans la trousse 49800-SMK de Leviton. B. L’outil de clivage AFL 92208-TB* peut être employé en présence de connecteurs FastCAM multimodes compris dans la trousse 49800-MMK de Leviton.
Remarque : étant donné les méthodes habituellement employées pour dénuder la fibre de 900 µm, une petite portion de gainage de 250 µm pourrait demeurer. Le cas échéant, cette portion ne doit pas dépasser 3 mm.
6. Insérer la fibre clivée à l’arrière du connecteur en la guidant délicatement dans l’ouverture du corps. 7.
Tenir la fibre à une distance d’environ 40-60 ������������������������� mm (1.57-2.35 in)�� derrière le connecteur, en maintenant une tension et une courbure légères (ce geste permet de s’assurer que la fibre reste en contact avec les composants internes). La marque faite sur la fibre devrait être à l’intérieur du corps.
8. En exerçant toujours une légère force sur la fibre, dégager la clé de came en la serrant latéralement.
10. Slide the boot up to engage over the rear of the connector body.
9. Faire basculer l’élément de verrouillage hors de la partie inférieure de la clé, et retirer cette dernière du connecteur.
11. Apply the connector housing onto the assembly from the front. Complete! Note: Dust cap over ferrule should remain in place until ready to insert connector.
10. Glisser le manchon vers le haut de manière à l’insérer sur l’arrière du corps du connecteur.
Note: This connector is not recommended for Outside Plant applications/installations. * Alternative cleavers were also tested. Those with a guaranteed maximum 1º cleave angle for single-mode fibers and a maximum 2º cleave angle for multimode fibers provided acceptable results.
Technical Support: 800-824-3005 Customer Service: 800-722-2082 International: 425-486-2222 Fax: 425-483-5270 Web: www.leviton.com
Vea las Ilustraciones correspondientes en el reverso de esta página.
4. Check fiber for integrity by bending the stripped end of the fiber slightly. This insures that you have not damaged it during the stripping step.
A. Fujikura CT-30A* cleaver is recommended for single-mode or multimode FastCAM connectors (included in Leviton installation kit 49800-SMK). B. AFL 92208-TB* cleaver can be used for multimode FastCAM connectors (included in Leviton installation kit 49800-MMK). Wedge Unit Clé de came Cuña
Illustrations correspondantes au verso.
11. Glisser le corps sur l’avant de l’assemblage. L’opération est terminée. Remarque : le capuchon pare-poussière devrait rester sur la ferrule jusqu’au moment de l’insertion du connecteur. Remarque : ce connecteur n’est pas recommandé pour les applications/installations extérieures. * D’autres outils de clivage ont également été mis à l’essai. Ceux ayant un angle minimal garanti de 1° au plus pour les fibres monomodes, et de 2° au plus pour les fibres multimodes ont donné des résultats satisfaisants.
2. Si utiliza fibra de 900µm, quite el tubo protector de la bota. Deslícelo hacia afuera en el frente de la bota. Deslice la bota sobre la fibra primero el extremo mas pequeño. 3.
Pele la fibra y remueva el revestimiento de pulido, dejando la fibra mas larga que el corte en la parte inferior (vea la Ilustración 1). Se recomienda limpiar la fibra con un paño de alcohol luego de pelar y antes de cortarla para remover polvo y residuos.
4. Revise la integridad física de la fibra doblando levemente el extremo. Esto asegura que la fibra no se haya dañado al ser pelada. 5.
Pele 13mm del revestimiento de la fibra de 900µm, o 10mm del revestimiento de la fibra de 250µm. Marque la fibra de 900µm a 11mm. Marque la fibra de 250µm a 14mm (vea la Ilustración 1). Alinee la marca con 24mm en la herramienta de corte. Proceda y raje la fibra de siguiendo las instrucciones de al herramienta.
A. Para conectores FastCAM modo sencillo o múltiple se recomienda la cortadora Fujikura CT-30* (incluida en el juego de instalación 49800-SMK de Leviton). B. Para conectores FastCAM modo múltiple se puede utilizar la cortadora AFL92208-TB* (incluida en el juego de instalación 49800-MMK de Leviton).
Nota: Dada la naturaleza del pelado mecánico de la fibra de 900µm, pueden quedar restos del revestimiento de 250µm. Estos deben mantenerse en una longitud máxima de 3mm.
6. Inserte la fibra cortada en la parte posterior del conector. Guíela cuidadosamente dentro de la abertura del cuerpo del conector. 7.
Sostenga la fibra a unos 40-60 mm (1.57-2.35 in). detrás conector, mantenga una leve tensión y dóblela. Esto asegura que la fibra preparada esté al lado de la fibra interna. Su marca en la fibra debe quedar dentro del cuerpo del conector.
8. Mantenga una leve tensión en la fibra y suelte la cuña presionán dola en ambos lados. 9. Gire el seguro desde la parte inferior de la cuña y remuévala del ensamblaje del conector. 10. Deslice la bota sobre la parte posterior del cuerpo del conector. 11. Para finalizar, coloque la caja del conector por el frente del ensamblaje. Nota: La cubierta contra polvo sobre el marco debe permanecer en su lugar hasta que esté lista para insertar el conector. Nota: No se recomienda el uso de este conector en aplicaciones a la intemperie o fuera de la planta. *Se probaron otros cortadores. Los que garantizan un ángulo de corte máximo de 1° para fibras modo sencillo y 2° en fibras modo múltiple obtuvieron resultados aceptables. PK-93356-10-02-0D 0R-93356-00-00-05
FIBER CONNECTOR SAFETY WARNINGS
SAFETY INFORMATION 1. Always wear safety glasses. 2. Isopropyl alcohol is flammable and may cause eye irritation. In case of contact with eyes, flush with water for at least 15 minutes. When using isopropyl alcohol, always assure proper levels of ventilation. In case of ingestion, consult a physician immediately. 3. Never look directly into a laser light source, point source at a person’s eyes, or point source at reflective surfaces. 4. When working on a fiber link, always turn laser source off, or disconnect completely. 5. Always dispose of fiber debris properly, preferably using sticky tabs. 6. Do not place food or beverages in the vicinity of the work area. 7. Thoroughly wash face and hands after terminating fiber. 8. Carefully remove any fiber debris that may have been stuck to clothing, or left in work area, and dispose of properly. TIPS AND RECOMMENDATIONS 1. Using isopropyl alcohol, thoroughly clean exposed fiber and buffer ensuring both are free from dust, oil, and debris. 2. Do not lay ferrule dust covers on a dirty or dusty surface. 3. Always use proper tools and/or accessories to terminate fibers and clean connector tips.
FIGURE 1
FIGURE 1
Fiber
0.9mm Buffer
13mm 0.51 in
10mm 0.39 in
11mm 0.43 in
Cleave length for 900µm buffered fiber.
NOTA: Las longitudes no son a escala
Marque
Mark
Mark Fiber
ILUSTRACIÓN 1
REMARQUE : les longueurs ne sont pas à l’échelle.
NOTE: Lengths are not to scale
Fibre
0.25mm Coated
Gaine de 0,90 mm
13mm 0.51 in
14mm 0.55 in
11mm 0.43 in
Longueur de clivage pour la fibre gainée de 900 µm.
Cleave length for 250µm coated fiber.
Marque Fibre
10mm 0.39 in
Marca
Marca
Gaine de 0,25 mm
14mm 0.55 in
Fibra
Pulido de 0,9mm
Fibra
13mm 0.51 in
11mm 0.43 in
10mm 0.39 in
Longitud del corte para fibra pulida de 900µm
Longueur de clivage pour la fibre gainée de 250 µm.
Revestimiento de 0,25mm
14mm 0.55 in
Longitud del corte para fibra revestida de 250µm
CONSIGNES DE SÉCURITÉ EN PRÉSENCE DE CONNECTEURS OPTIQUES
CONSIGNES DE SÉCURITÉ 1. On doit toujours porter des lunettes de sécurité. 2. L’isopropanol est inflammable et peut entraîner des irritations oculaires.� S’il ���������������� entre en ontact avec les yeux, les rincer à l’eau pendant au moins 15 minutes.� En ������������������� présence de ce composé, il faut toujours s’assurer que la ventilation soit adéquate.����������������������� ���������������������� Consulter un médecin sans délai en cas d’ingestion. 3. On ne doit jamais regarder directement une source laser, la pointer vers les yeux de quelqu’un d’autre, ni la diriger vers des surfaces réfléchissantes. 4. Lorsqu’on effectue des raccordements optiques, il faut toujours couper la source laser ou la déconnecter complètement. 5. On doit toujours éliminer les débris de fibre de la manière prescrite, en utilisant de préférence des languettes adhésives. 6. Il ne faut pas mettre d’aliments ou de boissons à proximité de l’aire de travail. 7. On doit se laver le visage et les mains en profondeur après avoir effectué des terminaisons optiques. 8. Il faut soigneusement retirer tous les débris de fibre accrochés aux vêtements ou laissés dans l’aire de travail, en les éliminant de la manière prescrite. CONSEILS ET RECOMMANDATIONS 1. Au moyen d’isopropanol, nettoyer en profondeur les fibres et la gaine afin d’en retirer toute trace de poussière, d’huile ou de débris. 2. Ne jamais déposer les capuchons de ferrule sur une surface sale ou poussiéreuse. 3. Toujours employer les outils ou accessoires appropriés pour effectuer les terminaisons optiques et nettoyer les pointes de connecteur.
2a.
1.
5b.
6.
2b.
7.
40 (1. -60 m 57 -2. m 35 in)
3.
8.
5a.
4.
10.
9.
11.
ADVERTENCIAS DE SEGURIDAD PARA CONECTORES DE FIBRA
INFORMACION 1. Siempre utilice gafas protectoras. 2. El alcohol isopropílico es inflamable y puede irritarle los ojos. Si entra en contacto con sus ojos, lávelos con agua durante un mínimo de 15 minutos. Cuando trabaje con alcohol isopropílico, hágalo en sitios con buena ventilación. Si lo ingiere, contacte a un médico inmediatamente. 3. Nunca dirija una luz láser a sus ojos, a los de un tercero, o a una superficie que lo pueda reflectar. 4. Cuando trabaje en un enlace de fibra siempre apague o desconecte completamente la fuente de láser. 5. Siempre deseche los residuos de fibra apropiadamente, preferentemente utilice papeles adhesivos. 6. No coloque comida o bebidas cerca del área de trabajo. 7. Lávese bien la cara y las manos luego de trabajar con fibras. 8. Remueva cuidadosamente cualquier residuo de fibra que pueda haberse adherido a sus prendas, o que quede en el área de trabajo y deséchelo apropiadamente. RECOMENDACIONES 1. Utilizando alcohol isopropílico, limpie completamente la fibra expuesta y suelta asegurando que ambas estén libres de polvo, aceite y residuos. 2. No apoye la tapas de las férulas sobre superficies sucias o con polvo. 3. Siempre utilice las herramientas y accesorios apropiados para terminar fibra y limpiar las puntas de los conectores.
2222 - 222nd Street SE Bothell, WA 98021, USA Phone: 425-486-2222 Fax: 425-483-5270
Leviton FastCAM Connectors - Ordering Information Description
Part Number
FastCAM ST MM 62.5µm
49991-MST
FastCAM ST MM 50µm
49991-5ST
FastCAM ST SM FastCAM SC MM 62.5µm FastCAM SC MM 50µm
49991-5SC
FastCAM SC MM 50µm Laser Optimized
Connecteurs FastCAM de Leviton – Renseignements pour la commande
Conectores FastCAM de Leviton – Como Ordenar
Description
Descripción
Numéro de catalogue
Número de Parte
49991-MST
FastCAM ST MM 62.5µm
49991-MST
FastCAM ST Multi 50,0 µm
49991-5ST
FastCAM ST MM 50µm
49991-5ST
49991-SST
FastCAM ST Mono
49991-SST
FastCAM ST SM
49991-SST
49991-MSC
FastCAM SC Multi 62,5 µm
49991-MSC
FastCAM SC MM 62.5µm
49991-MSC
FastCAM SC Multi 50,0 µm
49991-5SC
FastCAM SC MM 50µm
49991-5SC
49991-LSC
FastCAM SC Multi 50 μm, optimisé pour le laser
49991-LSC
FastCAM SC MM 50μm Laser Optimo
49991-LSC
FastCAM SC SM
49991-SSC
FastCAM SC Mono
49991-SSC
FastCAM SC SM
49991-SSC
FastCAM LC MM 62.5µm
49991-MLC
FastCAM LC Multi 62,5 μm
49991-MLC
FastCAM LC MM 62.5μm
49991-MLC
FastCAM LC MM 50µm Standard
49991-5LC
FastCAM LC Multi 50 μm, régulier
49991-5LC
FastCAM LC MM 50μm Estándar
49991-5LC
FastCAM LC MM 50µm Laser Optimized
49991-LLC
FastCAM LC Multi 50 μm, optimisé pour le laser
49991-LLC
FastCAM LC MM 50μm Laser Optimo
49991-LLC
FastCAM LC SM
49991-SLC
FastCAM, LC, Mono
49991-SLC
FastCAM LC SM
49991-SLC
Installation Kits
FastCAM ST Multi 62,5 µm
Trousses d’installation
Juegos de Instalación
Single-mode/Multimode
49800-SMK
Monomodes/multimodes
49800-SMK
Modo sencillo / Modo múltiple
49800-SMK
Multimode
49800-MMK
Multimodes
49800-MMK
Modo múltiple
49800-MMK
PK-93356-10-02-0D 0R-93356-00-00-05
FOLDING INSTRUCTIONS - 11" X 17" DO NOT PRINT
PK-93356-10-02-0D 0R-93356-00-00-05
