Atornille las bombillas en los enchufes. Consulte la etiqueta del casquillo de la lámpara para obtener información Max. Potencia. 1. 2. 3. BOMBILLA. 4.
Wall GENERAL PRODUCT INFORMATION: This product is listed by one of the following “Nationally Recognized Testing Laboratory”
This product is suitable for damp locations.
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
This product may be dimmed with a standard incandescent dimmer.
Use minimum 90°c supply conductors.
These fixtures are intended to be installed utilizing NEC compliant junction boxes.
This instruction shows a typical installation.
1A
1
4
LAMP
3
CANDLE FOLLOWER
CANDLE TUBE
2
SOCKET
1
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box.
2
Install the candle tubes by slipping them over the socket.
3
Install the candle followers by placing them on top of the candle tubes.
4
Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information.
1
1.0
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c.
1A
1
4
AMPOULE
3
ADEPTE DE BOUGIE
TUBE BOUGIE
2
DOUILLE
1
Suivez les instructions d'installation de suppléments fermés pour l'installation électrique et le luminaire sur une boîte de jonction.
2
Installez le tube de bougies en la glissant sur les douilles.
3
Installer les fouloirs de bougie en les plaçant sur le dessus de tubes de bougie.
4
Visser l’ampoules dans les douilles. Reportez-vous à l'étiquette sur la douille de le luminaire pour obtenir des informations de Max Puissance.
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c.
1A
1
4
BOMBILLA
3
SEGUIDOR DE VELA TUBO DE VELA
2
ENCHUFE
1
Siga las instrucciones de instalación de suplementos cerrados para la instalación eléctrica y el accesorio sobre la caja de junctura.
2
Instale los tubos de vela por el deslizamiento por encima de los enchufes.
3
Instalar los seguidors de vela colocándolo en la parte superior de los tubos de vela.
4
Atornille las bombillas en los enchufes. Consulte la etiqueta del casquillo de la lámpara para obtener información Max Potencia.
1. Installation Instructions for. Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box. Install the candle tubes by slipping them over the socket. Install the candle followers by placing t
Screws the lamp into the sockets. Refer to the label on the socket for Max Wattage information. ... 7400 Linder Ave, Skokie, IL 160077. 800.969.3347 www.Feiss.
Conecte el cable negro de la lámpara al cable de alimentación de línea caliente con un tapón de alambre. Monte el base de la lámpara en la placa de montaje y fíjela con los tornillos de la lámpara. Instale el tubo de vela lo deslizándose a través del
Secure the mounting plate to the electrical box with the two mounting plate screws. Connect the fixture ground wire to a suitable ground in accordance to local electrical codes. Connect the white fixture wire to the neutral power line wire ... and th
with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. 7. Matrimonio 2 Light Wall. 1.0. W 1745. B.
Connect the white fixture wire to the neutral power line wire with a wire nut. ... Conecte el cable blanco de la lámpara al cable de energía de la línea neutral con ...
Install all glass panels by carefully sliding them into the housing and securing them using the clips. Install the frame to the housing and secure it to the housing using the frame screws. Screw the lamps into the sockets. Refer to the label on the s
CAUTION RISK OF FIRE. -. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and ...
Install and secure the string of beads by hooking them to the top and bottom of the fixture. Install the candle tube by slipping through the socket. Install candle ...
Suivez les instructions d'installation jointes supplément pour l'installation électrique et de fixation sur la boîte de sortie de la maison. Vissez la lampe dans la ...
Coloque la base de la lámpara en los esparragos de montaje y seguro en su lugar atornillando las tuercas capuchon en los esparragos. Atornille las en los ...
Wembley Park 3 Light Outdoor Wall Lantern. 1.1. O 9505. L. Outdoor. O 9505. L. Follow enclosed supplement installation instructions for electrical and fixture ...
Screw the lamps into the sockets. Refer to the label on the socket for Max Wattage information. ... 7400 Linder Ave, Skokie, IL 160077. 800.969.3347 www.Feiss.
23 jun. 2016 - Headquarters/Eastern Distribution Center. 44 Harbor Park Drive. Port Washington, NY 11050. Central Distribution Center. 1600 Distribution Ct.
W 1782. B. Wall. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing compliant. NEC junction boxes. This product is ...
WB1713. WB1713. Install the glass panels by sliding them into the fixture and securing them using the tabs. Secure the mounting plate to the electrical box with ...
Mount the fixture base onto the mounting plate and secure it with the Allen screws using an Allen wrench. Screw the lamp into the socket. Refer to the label on ...
Hamlet 1, 2, 3, and 4 Light Vanity Strip. 1.0. V 2250_. S. V 22501, V 22502,. S. S. V 22503, V 22504. S. S. Secure the mounting plate to the junction box. Connect the fixture ground wire to a suitable ground in accordance to local electrical codes. C
Conecte el cable blanco de la lámpara al cable de energía de la línea neutral con un tapón de alambre. Conecte el cable negro de la lámpara al cable de alimentación de línea caliente con un tapón de alambre. Monte el base de la lámpara en la placa de
Insert the crystal into the cover and secure it to the shade base using the washers and screws. Repeat for multiple crystals. Place the shade and spacer onto the ...
Fije la placa de montaje a la caja eléctrica con los dos tornillos de la placa de montaje. ... Conecte el cable blanco de la lámpara al cable de energía de la línea ...
Place the shade and spacer over the socket, then secure them in place by screwing the shade collar nut onto the socket; repeat for remaining sockets. Screw the ...
