the applicable installation code by a person familiar with the construction ... Ce produit doit être installé conformément au code ... A Generation Brands Company.
Pendant GENERAL PRODUCT INFORMATION: These fixtures are intended to be installed utilizing NEC compliant junction boxes.
This product may be dimmed with a standard incandescent dimmer.
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
This instruction shows a typical installation.
Use minimum 90°c supply conductors.
This product is safety listed for dry locations only.
1A FIXTURE SCREW
7
1
6 MOUNTING PLATE
2 ALLEN WRENCH
8
3
CANOPY
4
SOCKET ASSEMBLY
9
STEM ASSEMBLY
LAMP
1
10
SHADE
1
Determine the height of the fixture with the provided stems and assemble them by screwing them together.
2
Secure the mounting plate to the electrical box with two mounting plate screws.
3
Feed the fixture wires through the stems and screw the stem assembly to the socket assembly.
4
Feed the fixture wires through the canopy and screw the canopy onto the stem assembly.
5
Connect the fixture to a suitable ground in accordance to local electrical codes.
6
Connect the white fixture wire (square and/or rigid) to the neutral power line wire with a wire nut.
7
Connect the black fixture wire (round and/or smooth) to the hot power line wire with a wire nut.
8
Neatly place all the wires into the electrical box, place the canopy onto the mounting plate, and secure it in place by screwing in the fixture screws with an Allen wrench.
9
Screw the lamp into the socket. Refer to the label on the lamp socket for Max Wattage information.
10
Install the shade to the socket assembly by screwing it in. 1
1.1
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c.
1A VIS DE LUMINAIRE
7
1
6 PLAQUE DE MONTAGE
2 CLE DE ALLEN
8
3
DAIS
4
ASSEMBLÉE DE DOUILLE
9
AMPOULE
1 ASSEMBLÉE DE TIGE
10
ABAT-JOUR
1
Déterminer la hauteur de le luminaire avec les tiges fournies et les assembler en les vissant ensemble.
2
Fixer la plaque de montage sur le boîte électrique avec deux vis de montage.
3
Faire passer les fils du luminaire à travers les tiges et visser l'assembleé de la tige à l'assembleé de la douille.
4
Faire passer les fils du luminaire à travers la dais et visser le dais sur l'assembleé de la tige.
5
Connectez le luminaire à un terrain approprié conformément aux codes électriques locaux.
6
Connectez le fil blanc de le luminaire (carré et/ou rigide) au fil ligne neutre avec un capuchon de connexion.
7
Connectez le fil noir de le luminaire (rond et/ou lisse) au fil ligne chaude avec un capuchon de connexion.
8
Parfaitement placer tous les fils dans la boîte électrique, placez la dais sur la plaque de montage et fixer en place en serrant les vis de luminaire avec une clé Allen.
9
Vissez l'ampoule dans la douille. Lire l'étiquette sur la douille de lampe pour informations Max Wattage.
10
Installer l'abat-jour à l'assembleé de la douille en le vissant dans.
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c.
1A TORNILLO DE LA LÁMPARA
7
1
6 PLACA DE MONTAJE
2 LLAVE DE ALLEN
8
3
DOSEL
4
ASAMBLEA DE ENCHUFE
9
BOMBILLA
10
PANTALLA
1 ASAMBLEA DE TALLO
1
Determinar la altura de la lámpara con los tallos proporcionados y montarlos atornillándolos juntos.
2
Fije la placa de montaje a la caja eléctrica con dos tornillos de montaje.
3
Pasar los cables de la lámpara a través de los tallos y atornille el tallo para la asamblea de enchufe.
4
Pasar los cables de la lámpara a través del dosel y atornille el dosel en la asamblea de tallo.
5
Conecte la lámpara a una tierra apropiada de acuerdo a los códigos eléctricos locales.
6
Conecte el cable blanco de la lámpara (cuadrado o rígido) para el cable neutro línea con una tuerca para hilos.
7
Conecte el cable negro de la lámpara (redondo o liso) para el cable de línea de energía caliente con una tuerca de alambre.
8
Cuidadosamente Coloque todos los cables en la caja eléctrica, coloque el dosel en la placa de montaje y asegúrelo en su lugar atornillando los tornillos de la lámpara con una llave Allen.
9
Enrosque la bombilla en el enchufe. Consulte la etiqueta en el enchufe de la lámpara para obtener información de Max Wattage.
10
Instale la pantalla en la asamblea del enchufe por atornillándolo en.
Install a quick link onto the chain and fixture loop, then install another quick link to the other ... place the canopy onto the mounting plate, and secure it in place by.
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box. Screw the lamp into the socket. Refer to the label ...
Place the shade over the socket, then secure it in place by tightening the collar nut. Screw the lamp into the socket. Refer to the label on the lamp socket for Max ...
Place the shade over the socket, then secure it in place by tightening the collar nut. Screw the lamp into the socket. Refer to the label on the lamp socket for Max ...
Determine la altura deseada de la lámpara alimentando el cable a través del dosel y moviendo el cable hacia arriba o hacia abajo. Coloque el cable entre los dos pinzas y asegúrelo en su lugar utilizando los tornillos de la pinza. Recortar el cable de
... instructions for electrical and fixture installation onto house outlet box. 1. 2. 1A. LAMP. 5. SOCKET ASSEMBLY. CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with t
Determine the wanted height of the fixture by feeding the cord through the canopy and moving the cord up or down. Place the cord in between the two cord clips ...
P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing ... Refer to the label on the lamp socket for Max Wattage information.
CAUTION RISK OF FIRE. -. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and ...
2. Suivez les instructions d'installation de suppléments fermés pour l'installation électrique et appareil sur une boîte de sortie de la maison. Placez l'abat-jour et l'espaceur sur le socket, puis fixez-les en place en vissant l'écrou de collier sur
P1302. Pendant. P1302. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing NEC compliant junction boxes. This product is safety listed for dry locations only. This product may be dimmed with a standard incandesc
with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. 1. 2 ... with the hex nut. Place the cup onto the threaded pipe and secure it in place with the finial. Follow enclosed supplement instal
Install all glass panels by carefully sliding them into the housing and securing them using the tabs. NOTE: Adjustment of the socket assembly may be required when installing glass panels. Install the candle followers by placing them on top of the can
Consulte la etiqueta del enchufe de la lámpara para obtener información Max de ... Fije la placa de montaje a la caja eléctrica con dos tornillos de la placa de ...
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. SHADE. TO
Frontage 1 Light Pendant. 1.0. P1369_P1370. Pendant. P1369, P1370. G. P. I. : ENERAL RODUCT NFORMATION. This product is listed by one of the following.
BOMBILLA. PRECAUCIÓN: RIESGO DE INCENDIO. Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan. Utilizar conductores de
P1299. Pendant. P1299. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing NEC compliant junction boxes. This product is safety listed for dry locations only. This product may be dimmed with a standard incandesc
NEC junction boxes. This product is safety listed for damp locations. Screw the lamp into the socket. Refer to the label on the socket for Max Wattage Information.
compliant. NEC junction boxes. This product is safety listed for damp locations. CAUTION RISK OF FIRE. -. This product must be installed in accordance with the.
... fixture by feeding the cord through the canopy and moving the cord up or down. ... Neatly place all the wires into the junction box, place the canopy onto the ...
