... instructions for electrical and fixture installation onto house outlet box. 1. 2. 1A. LAMP. 5. SOCKET ASSEMBLY. CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
Pendant GENERAL PRODUCT INFORMATION: These fixtures are intended to be installed utilizing NEC compliant junction boxes.
This product may be dimmed with a standard incandescent dimmer.
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
This instruction shows a typical installation.
Use minimum 90°c supply conductors.
This product is safety listed for dry locations only.
1A 5
SOCKET ASSEMBLY THUMB SCREW
3
2
NUT
LAMP
WASHER
SHADE
3
THREADED PIPE
1 WASHER
NUT DECORATIVE CUP
4 FINIAL 1
Screw a nut onto one end of the threaded pipe, then place the shade and a washer over the other end of the threaded pipe and secure them together by tightening with the other nut.
2
Screw the lamp into the socket. Refer to the label on the lamp socket for Max Wattage information.
3
Install the shade to the socket assembly and secure it in place by using the thumb screws.
4
Place the decorative cup over the threaded pipe and secure them in place by tightening the finial.
5
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box.
1
1.1
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c.
1A 5
ASSEMBLÉE DE DOUILLE VIS DE POUCE
3
2
ECROU
AMPOULE
RONDELLE
ABAT-JOUR
3
TUYAU FILETÉ
1 RONDELLE
ECROU COUPE DÉCORATIF
4 FLEURON 1
Vissez un écrou sur une extrémité de la tige filetée, puis placez l'ombre et une rondelle sur l'autre extrémité de la tige filetée et fixez-les ensemble en serrant avec l'autre noix.
2
Vissez l'ampoule dans la douille. Lire l'étiquette sur la douille de lampe pour informations Max Wattage.
3
Installer l'abat-jour à la assemblée de douille et fixez-le à l'aide des vis de pouce.
4
Placer le coupe décoratif sur le tuyau fileté et fixez-les en place en serrant le fleuron.
5
Suivez supplément ci-joint des instructions électriques et installation d'accessoires dans la boîte de prise de maison.
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c.
1A 5
ASAMBLEA DE ENCHUFE TORNILLO DE PULGAR
3
2
TUERCA
BOMBILLA
ARANDELA
PANTALLA
3
TUBO ROSCADO
1 ARANDELA
TUERCA COPA DECORATIVA
4 FINIAL 1
Enrosque una tuerca en un extremo de el tubo roscado, luego coloque la pantalla y una arandela sobre el otro extremo del tubo roscado y fíjelos juntos apretando con la otra tuerca.
2
Enrosque la bombilla en el enchufe. Consulte la etiqueta en el zócalo de la lámpara para obtener información de Max Wattage.
3
Instalar la pantalla a la asamblea de enchufe y asegúrelo en su lugar utilizando los tornillos de pulgar.
4
Coloque la copa decorativa sobre el tubo roscado y fíjelos en su lugar apretando el finial.
5
Siga las instrucciones de Instalación incluido suplemento para eléctricos e instalación del accesorio en la caja de enchufe de casa.
Install a quick link onto the chain and fixture loop, then install another quick link to the other ... place the canopy onto the mounting plate, and secure it in place by.
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box. Screw the lamp into the socket. Refer to the label ...
Place the shade over the socket, then secure it in place by tightening the collar nut. Screw the lamp into the socket. Refer to the label on the lamp socket for Max ...
the applicable installation code by a person familiar with the construction ... Ce produit doit être installé conformément au code ... A Generation Brands Company.
Place the shade over the socket, then secure it in place by tightening the collar nut. Screw the lamp into the socket. Refer to the label on the lamp socket for Max ...
Determine la altura deseada de la lámpara alimentando el cable a través del dosel y moviendo el cable hacia arriba o hacia abajo. Coloque el cable entre los dos pinzas y asegúrelo en su lugar utilizando los tornillos de la pinza. Recortar el cable de
Determine the wanted height of the fixture by feeding the cord through the canopy and moving the cord up or down. Place the cord in between the two cord clips ...
P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing ... Refer to the label on the lamp socket for Max Wattage information.
CAUTION RISK OF FIRE. -. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and ...
2. Suivez les instructions d'installation de suppléments fermés pour l'installation électrique et appareil sur une boîte de sortie de la maison. Placez l'abat-jour et l'espaceur sur le socket, puis fixez-les en place en vissant l'écrou de collier sur
P1302. Pendant. P1302. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing NEC compliant junction boxes. This product is safety listed for dry locations only. This product may be dimmed with a standard incandesc
with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. 1. 2 ... with the hex nut. Place the cup onto the threaded pipe and secure it in place with the finial. Follow enclosed supplement instal
Install all glass panels by carefully sliding them into the housing and securing them using the tabs. NOTE: Adjustment of the socket assembly may be required when installing glass panels. Install the candle followers by placing them on top of the can
Consulte la etiqueta del enchufe de la lámpara para obtener información Max de ... Fije la placa de montaje a la caja eléctrica con dos tornillos de la placa de ...
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. SHADE. TO
Frontage 1 Light Pendant. 1.0. P1369_P1370. Pendant. P1369, P1370. G. P. I. : ENERAL RODUCT NFORMATION. This product is listed by one of the following.
BOMBILLA. PRECAUCIÓN: RIESGO DE INCENDIO. Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan. Utilizar conductores de
P1299. Pendant. P1299. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing NEC compliant junction boxes. This product is safety listed for dry locations only. This product may be dimmed with a standard incandesc
NEC junction boxes. This product is safety listed for damp locations. Screw the lamp into the socket. Refer to the label on the socket for Max Wattage Information.
compliant. NEC junction boxes. This product is safety listed for damp locations. CAUTION RISK OF FIRE. -. This product must be installed in accordance with the.
... fixture by feeding the cord through the canopy and moving the cord up or down. ... Neatly place all the wires into the junction box, place the canopy onto the ...
