P1299. Pendant. P1299. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing NEC compliant junction boxes. This product is safety listed for dry locations only. This product may be dimmed with a standard incandescent dimmer. This instruction shows a typical installation.
Pendant GENERAL PRODUCT INFORMATION: These fixtures are intended to be installed utilizing NEC compliant junction boxes.
This product may be dimmed with a standard incandescent dimmer.
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
This instruction shows a typical installation.
Use minimum 90°c supply conductors.
This product is safety listed for dry locations only.
1A 3
JEWEL
5 FIXTURE
2 SHADE
LAMP
4
1
If necessary, place the fixture upside down on a flat surface.
2
Temporarily remove the counter ring from the socket, then place the shade over the socket and secure it by reinstalling the counter ring.
3
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box.
4
Screw the lamp into the socket. Refer to the label on the lamp socket for Max Wattage information.
5
Hang the jewels by hooking them to the fixture as shown on drawing.
1
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c.
1A 3
BIJOU
5 LUMINAIRE
2 ABAT-JOUR
AMPOULE
4
1
Si nécessaire, placer le montage à l'envers sur une surface plane.
2
Temporairement retirer l'anneau de compteur de la douille, puis placez l'abat-jour sur la douille et le fixer en réinstallant l'anneau de compteur.
3
Reportez-vous aux instructions pour supplément clos électrique et installation de luminaire sur boîte de sortie de maison.
4
Vissez l'ampoule dans la douille. Lire l'étiquette sur la douille de lampe pour informations Max Wattage.
5
Accrocher les bijoux en les accrochant à le luminaire comme indiqué sur le dessin.
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c.
1A 3
JOYA
5 LÁMPARA
2 PANTALLA
BOMBILLA
4
1
Si es necesario, coloque la lámpara boca abajo sobre una superficie plana.
2
Temporalmente quite el anillo contador del enchufe, luego coloque la pantalla sobre el zócalo y asegúrelo reinstalando el anillo contador.
3
Siga las instrucciones de Instalación incluido suplemento para eléctricos e instalación de la lámpara en la caja de enchufe de casa.
4
Enrosque la bombilla en el enchufe. Consulte la etiqueta en el zócalo de la lámpara para obtener información de Max Wattage.
5
Cuelgue las joyas enganchando los en la lámpara, como se muestra en el dibujo.
Installer l'abat-jour en le plaçant sur la ampoule. Répétez les étapes 3 à 5 pour les douilles restants. Reportez-vous aux instructions pour supplément clos ...
Connect the white fixture wire to the neutral power line wire with a wire nut. ... Conecte el cable blanco de la lámpara al cable de energía de la línea neutral con ...
Consulte la etiqueta del enchufe de la lámpara para obtener información Max de ... Fije la placa de montaje a la caja eléctrica con dos tornillos de la placa de ...
Allier 1 Light Chandelier. 1.1. F2952-1-F2953-1. Chandelier. F2952/1, F2953/1_. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be ...
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. SHADE. TO
Frontage 1 Light Pendant. 1.0. P1369_P1370. Pendant. P1369, P1370. G. P. I. : ENERAL RODUCT NFORMATION. This product is listed by one of the following.
W 1782. B. Wall. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing compliant. NEC junction boxes. This product is ...
Connect the black fixture wire (round and/or smooth) to the hot power line wire with a wire ... Refer to the label on the lamp socket for Max Wattage information. 1.
WB1713. WB1713. Install the glass panels by sliding them into the fixture and securing them using the tabs. Secure the mounting plate to the electrical box with ...
Mount the fixture base onto the mounting plate and secure it with the Allen screws using an Allen wrench. Screw the lamp into the socket. Refer to the label on ...
National Fire Protection Association (NFPA), and the American ... FlexTM Series Humidity Sensing Fan/Light ONLY:Do not use a speed .... controller module.
Secure the mounting plate to the electrical box with the two provided mounting plate screws. Connect the fixture ground wire to a suitable ground in accordance to local electrical codes. Connect the white fixture wire to the neutral power line wire w
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and ...
the applicable installation code by a person familiar with the construction ... Ce produit doit être installé conformément au code ... A Generation Brands Company.
Place the shade over the socket, then secure it in place by tightening the collar nut. Screw the lamp into the socket. Refer to the label on the lamp socket for Max ...
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box. Screw the lamp into the socket. Refer to the label ...
compliant. NEC junction boxes. This product is safety listed for damp locations. CAUTION RISK OF FIRE. -. This product must be installed in accordance with the.
Place the shade over the socket, then secure it in place by tightening the collar nut. Screw the lamp into the socket. Refer to the label on the lamp socket for Max ...
Use this unit only in the manner intended by the manufacturer. ... visit our website - www.broan.com or www.nutone.com. - to register this product and to view installation tips and videos. HOUSING. TABS. Cooking. Equipment. Floor ... or instructions,
of gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer's guideline and safety ...
