junction boxes. This product is safety listed for damp locations. This product may be dimmed with a standard incandescent dimmer. This instruction shows a ...
Ceiling GENERAL PRODUCT INFORMATION: These fixtures are intended to be installed utilizing NEC compliant junction boxes.
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
This product is safety listed for damp locations. This product may be dimmed with a standard incandescent dimmer.
Use minimum 90°c supply conductors.
This instruction shows a typical installation.
1A
1
THREADED NIPPLE
4 THUMB SCREW SOCKET LAMP
2 3
3
3
CAP NUT
4 SHADE
1
1
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box.
2
Place the fixture base over the threaded nipple and secure it in place with the cap nut.
3
Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information.
4
Install the shade by aligning it with the fixture base, then using the thumb screws to secure them together.
1
1.1
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c. 1A
1
ATTACHE FILETE
4 VIS DE POUCE DOUILLE AMPOULE
2 3
3
3
ECROU DE CASQUETTE
4 ABAT-JOUR
1
Suivez les instructions d'installation jointes supplément pour l'installation électrique et de fixation sur la boîte de sortie de la maison.
2
Placez la base de l'appareil sur le raccord et le fixer en place avec l'écrou de casquette.
3
Visser les lampes dans les douilles. Reportez-vous à l'étiquette sur la douille de lampe Puissance max pour plus d'informations.
4
Installer l'abat-jour en les alignant sur la base du luminaire, puis à l'aide des vis de pouce pour fixer ensemble.
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c. 1A
1
CONECTADOR ROSCADO
4 TORNILLO DE PULGAR ENCHUFE BOMBILLA
2 3
3
3
TUERCA DE CASQUILLO
4 PANTALLA
1
Siga las instrucciones de instalación adjuntas suplemento para la instalación eléctrica y la lámpara en la caja de salida casa.
2
Coloque la base de la lámpara sobre el conectador roscado y asegúrelo en su lugar con la tuerca de casquillo.
3
Atornille las bombillas en los enchufes. Consulte la etiqueta en el enchufe de la lámpara para obtener información de Max Wattage.
4
Instale la pantalla alineándola con el base de la lámpara y luego utilizando los tornillos de pulgar para fijarlos juntos.
Install the mounting plate to the junction box with junction box screws (not provided) ... screws to mount the fixture later. ... Use minimum 90°c supply conductors.
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box. Place the fixture base over the threaded nipple and secure it in place with the cap nut. ... with the construction and operation of th
Refer to the label on the lamp socket for Max Wattage information. Install the shade by aligning it with the fixture base, then using the thumb screws to secure ...
qu'il entraîne. Utiliser les conducteurs d'alimentation supérieure à 90° c. VIS DE POSTE. POSTE. 1. 2. 3. 4. 5. 6. 7. AMPOULE. PANNEAU DE VERRE. 5. 6. 7 ...
Connect the white fixture wire to the neutral power line wire with a wire nut. Connect ... tightening the fixture screws into the nuts. 1. 2 ... Feiss reserves the right to.
Place the shade and spacer over the socket, then secure them in place by tightening the collar nut. Screw the lamp into the socket. Refer to the label on the ... Conecte el cable negro de la lámpara (redonda y / o suave) al cable de la línea eléctric
Connect the black fixture wire to the hot power line wire with a wire nut. Place the fixture ... applicable installation code by a person familiar with the construction ...
Coloque la base de la lámpara en los esparragos de montaje y seguro en su lugar atornillando las tuercas capuchon en los esparragos. Atornille las en los ...
Place the rubber washer, the shade, and large washer onto the threaded pipe (in that order), then secure them in place using a hex nut. Place the decorative cup ...
registered trademark of Feiss. Feiss reserves the right to change specifications for product improvements without notification. A Generation Brands Company.
Place the shade, shade ring, diffuser, and washer (in that order) onto the threaded pipe and secure it in place with the hex nut (Do not over tighten). Place the ...
TUYAU FILETÉ. GOUJON DE MONTAGE. 2. Fixer la plaque de montage sur le boîte de jonction. Installez les panneaux de verre en les insérant avec précaution dans le cadre et les fixer à l'aide des languettes. Connecter le luminaire à un terrain approprié
junction boxes. This product is safety listed for dry locations only. This product may be dimmed with a standard incandescent dimmer. This instruction shows a ...
Place the pipe cover, spacer, steel washer, rubber washer, shade, rubber washer, and steel washer onto the threaded pipe in that order, then secure them in ...
registered trademark of Feiss. Feiss reserves the right to change specifications for product improvements without notification. A Generation Brands Company.
Hounslow 1 Light Pendant. 1.1. P1309-P1310-P1319-P1320. Pendant. P1309, P1310,. P1319, P1320. Place the shade and spacer over the socket, then secure ...
Refer to the label on the lamp socket for Max Wattage information. Repeat steps 1-3 for remaining sockets. Using the help of another person, connect the upper ...