Place the rubber washer, the shade, and large washer onto the threaded pipe (in that order), then secure them in place using a hex nut. Place the decorative cup ...
Ceiling GENERAL PRODUCT INFORMATION: CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
These fixtures are intended to be installed utilizing NEC compliant junction boxes. This product is safety listed for damp locations.
Use minimum 90°c supply conductors.
This product may be dimmed with a standard incandescent dimmer. This instruction shows a typical installation.
1A 1
SOCKET ASSEMBLY LAMP
2 3
THREADED PIPE
RUBBER WASHER
4
SHADE
LARGE WASHER HEX NUT DECORATIVE CUP
5
FINIAL 1
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box.
2
Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information.
3
Screw the threaded pipe to the bottom of socket assembly.
4
Place the rubber washer, the shade, and large washer onto the threaded pipe (in that order), then secure them in place using a hex nut.
5
Place the decorative cup onto the threaded pipe and secure it in place using the finial.
1
1.1
MISE EN GARDE - RISQUE D'INCENDIE Ce produit doit être installé selon le code d’installation pertinent , par une personne qui connaÎt bien le produit et son fonctionnement ainsi que les risques inhérents
Les fils d’alimentation doivent convenir pour 90°c. 1A 1
ENSEMBLE DE DOUILLE AMPOULE
2 3
TUYAU FILETÉ
RONDELLE DE GOMME
4
ABAT-JOUR
RONDELLE GRANDE ECROU HEX COUPE DÉCORATIVE
5
FLEURON 1
Suivez les instructions d'installation de suppléments fermés pour l'installation électrique et appareil sur une boîte de sortie de la maison.
2
Vissez le tuyau fileté au fond de l'ensemble de douille.
3
Visser les ampoules dans les douilles. Reportez-vous à l'étiquette sur la douille de le luminaire pour obtenir des informations de Max Puissance.
4
Placez la rondelle de gomme, l'abat-jour, et la grande rondelle sur le tuyau fileté (dans cet ordre), puis les fixer en place à l'aide d'un écrou hexagonal.
5
Placez la coupe décorative sur le tuyau fileté et fixer en place à l'aide du fleuron.
2
ADVERTENCIA - RIESGO DE INCENDIO Este productor debe ser instalado segun el codigo de instalacion aplicable por una persona que conozca la constussion y el funcionamiento del producto y los riesgos que supone.
Conductores de alimentacion 90°c Min. 1A 1
ASAMBLEA DE ENCHUFE BOMBILLA
2 3
TUBO ROSCADO
ARANDELA DE GOMA
4
PANTALLA
ARANDELA GRANDE TUERCA HEX COPA DECORATIVA
5
FINIAL 1
Siga las instrucciones de instalación de suplementos cerrados para la instalación eléctrica y el accesorio sobre la caja de salida de la casa.
2
Atornillar el tubo roscado a la parte inferior del asamblea de enchufe.
3
Atornille las bombillas en los enchufes. Consulte la etiqueta del casquillo de la lámpara para obtener información Max Potencia.
4
Coloque la arandela de goma, la pantalla, y la arandela grande en el tubo roscado (en ese orden), luego fijarlos en su lugar con una tuerca hexagonal.
5
Coloque la copa decorativa sobre el tubo roscado y fijarlo en su lugar con el finial.
Coloque la base de la lámpara en los esparragos de montaje y seguro en su lugar atornillando las tuercas capuchon en los esparragos. Atornille las en los ...
registered trademark of Feiss. Feiss reserves the right to change specifications for product improvements without notification. A Generation Brands Company.
Place the shade, shade ring, diffuser, and washer (in that order) onto the threaded pipe and secure it in place with the hex nut (Do not over tighten). Place the ...
Connect the fixture to a suitable ground in accordance to local electrical codes. Connect the white fixture wire to the neutral power line wire with a wire nut. Connect the black fixture wire to the hot power line wire with a wire nut. Mount the fixt
Mark the anchor hole locations on the mounting plate and remove the mounting plate. ... Atornille los tornillos de anclaje en los anclajes. Conecte el lámpara a ...
Place the shade, shade ring, diffuser, and washer (in that order) onto the threaded pipe and secure it in place with the hex nut. (Do not over tighten). Place the ...
Installation Instructions for. Hamlet 2 Light Semi-Flush Mount. 1.0. SF325. SF325. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be ...
Evington 2 Light Semi-Flush Mount. 1.0. SF334. SF334. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing compliant.
Place the shade, shade ring, diffuser, and washer (in that order) onto the threaded pipe and secure it in place with the hex nut (Do not over tighten). Place the ...
Place the shade and spacer over the socket, then secure them in place by tightening the collar nut. Screw the lamp into the socket. Refer to the label on the ... Conecte el cable negro de la lámpara (redonda y / o suave) al cable de la línea eléctric
Connect the black fixture wire to the hot power line wire with a wire nut. Place the fixture ... applicable installation code by a person familiar with the construction ...
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box. Place the fixture base over the threaded nipple and secure it in place with the cap nut. ... with the construction and operation of th
junction boxes. This product is safety listed for damp locations. This product may be dimmed with a standard incandescent dimmer. This instruction shows a ...
Connect the black fixture wire to the hot power line wire with a wire nut. Mount the fixture base onto the mounting plate studs and secure it with the knurled nuts.
TUYAU FILETÉ. GOUJON DE MONTAGE. 2. Fixer la plaque de montage sur le boîte de jonction. Installez les panneaux de verre en les insérant avec précaution dans le cadre et les fixer à l'aide des languettes. Connecter le luminaire à un terrain approprié
... then secure them in place by screwing the shade collar nut onto the socket; ... de suplementos cerrados para la instalación eléctrica y el accesorio sobre la ...
Place the pipe cover, spacer, steel washer, rubber washer, shade, rubber washer, and steel washer onto the threaded pipe in that order, then secure them in ...
Connect the black fixture wire (round and/or smooth) to the hot power line ... Place the shade inside of the decorative ring and secure it in place using the tabs.
