These fixtures are intended to be installed utilizing compliant junction. NEC boxes. This product is safety listed for wet locations. Incandescent lamps may be ...
Outdoor GENERAL PRODUCT INFORMATION: These fixtures are intended to be installed utilizing NEC compliant junction boxes. Incandescent lamps may be dimmed with a standard incandescent dimmer. LED lamps may be dimmed with a LED dimmer. Consult lamp manufacturer for additional information.
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
This instruction shows a typical installation.
Use minimum 90°c supply conductors.
This product is safety listed for wet locations.
1A
2
FIXTURE
1
LAMP
3
1
Screw the lamps into the sockets. Refer to the label on the socket for Max Wattage information.
2
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box.
3
For wet locations, caulk around the base of the fixture with waterproof construction sealant.
1
1.0
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c.
1A
3 LUMINAIRE
1
AMPOULE
3
1
Vissez les ampoules dans les douilles. Reportez-vous à l'étiquette sur la prise pour les informations Max Wattage.
2
Suivez les instructions d'installation complétées pour l'installation électrique et de montage sur la boîte de sortie de la maison.
3
Pour les endroits humides, calfeutrer autour de la base de l'appareil avec un joint d'étanchéité étanche à l'eau.
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c.
1A
2 LÂMPARA
1
BOMBILLA
3
1
Atornille las bombillas en los enchufes. Consulte la etiqueta en el enchufe para obtener información sobre el Vatiaje máximo.
2
Siga las instrucciones adjuntas de instalación del suplemento para la instalación eléctrica y de accesorios en la caja de salida de la casa.
3
Para lugares húmedos, calafatear alrededor de la base del aparato con sellador de construcción impermeable.
Insert the glass panels into the shade, then secure them by installing the brackets using the screws and washers. Install the LED assembly to the top fixture using ...
Insert the diffuser into the diffuser base, then install the diffuser cover to the bottom of the fixture and secure it in place with the cover screws. Connect the fixture ...
This product is safety listed for wet locations. For a complete list of dimmers, visit out website at www.Feiss.com. CAUTION RISK OF FIRE. -. This product must be ...
Conecte el cable blanco de la lámpara al cable de línea de alimentación neutra con una tuerca para cable. Conecte el cable negro de la lámpara al cable de línea de alimentación caliente con una tuerca para cable. Monte la base de la lámpara sobre la
Place the washer, outer shade, small spacer, inner shade, and large spacer over the socket (in that order), then secure them in place by tightening with the collar ...
Install all glass panels (except the door) by carefully sliding them into the fixture and ... Place the shade and spacer over the socket and secure them in place by ...
NEC junction boxes. This product is safety listed for damp locations. Screw the lamp into the socket. Refer to the label on the socket for Max Wattage Information.
Percer des trous de la taille appropriée aux emplacements marqués et installez les ancres. Fixez la plaque de montage à la boîte de jonction. Visser les vis ...
Conecte el cable negro de la lámpara al cable de línea eléctrica caliente con ... Monte la base de lámpara sobre la placa de montaje y fijarlo con los tornillos de ...
This product may be dimmed with a standard incandescent dimmer. This instruction shows a typical installation. Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box. Install the shade by pl
Screw the lamp into the socket. Refer to the label on the socket for Max Wattage information. Place the cover onto the frame nipple and secure it in place by screwing the cap onto the nipple. 6. CAUTION RISK OF FIRE. -. This product must be installed
Connect the black fixture wire to the hot power line wire with a wire nut. Neatly place the wires and wire nut connections into the junction box, mount the fixture ...
Percer des trous de la taille appropriée aux emplacements marqués et installez les ancres. Fixez la plaque de montage à la boîte de jonction. Visser les vis ...
Instalar temporalmente la placa de montaje a la caja de juntura. Marque las ubicaciones de los orificios de anclaje en la placa de montaje y retire la placa de montaje. Taladro agujeros de tamaño apropiado en los lugares marcados y instalar los ancla
CADRE. ATTACHE. VIS DE CADRE. FLEURON. 2. ATTENTION : RISQUE D'INCENDIE. Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il en
registered trademark of Feiss. Feiss reserves the right to change specifications for product improvements without notification. A Generation Brands Company.
compliant. NEC junction boxes. This product is safety listed for damp locations. CAUTION RISK OF FIRE. -. This product must be installed in accordance with the.
luminaire et le fixer avec la petite vis de fixation à l'aide d'une clé Allen. Fixez le bras à la ... 555 Theodore Fremd Ave Suite B101 Rye, NY 10580. 800.969.3347.
Refer to the label on the lamp socket for Max Wattage information. Place and secure shade onto ... 7400 Linder Ave, Skokie, IL 60077. 800.969.3347 www.Feiss.
This instruction shows a typical installation. CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box. Install the candle follower by placing it on top of the candle tube. Screw the lamp into the ... and the hazards involved. Use minimum
Install and secure the string of beads by hooking them to the top and bottom of the fixture. Install the candle tube by slipping through the socket. Install candle ...
CAUTION RISK OF FIRE. -. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and ...
