Chandelier GENERAL PRODUCT INFORMATION: This product is listed by one of the following “Nationally Recognized Testing Laboratory” These fixtures are intended to be installed utilizing NEC compliant junction boxes.
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
This product is suitable for dry locations only.
Use minimum 90°c supply conductors.
This product may be dimmed with a standard incandescent dimmer. This instruction shows a typical installation.
1A 6
2
FIXTURE LOOP
FRAME SWIVEL
2
5
LAMP
4
CANDLE FOLLOWER
3
CANDLE TUBE
STEM
SOCKET
1 SOCKET ASSEMBLY
1
For 6 Light Version Only: Feed the cord through the stem and screw it to the socket assembly.
2
Feed the cord through the swivel and fixture loop, then screw the stem to the swivel and fixture loop onto the frame.
3
Install the candle tubes by slipping them over the sockets.
4
Install the candle followers by placing them on top of the candle tubes.
5
Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information.
6
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box.
1
1.0
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c. 1A 6
2
BOUCLE DE LUMINAIRE
CADRE PIVOT
2
5
AMPOULE
4
ADEPTE DE BOUGIE
3
TUBE BOUGIE
TIGE
DOUILLE
1 ENSEMBLE DE DOUILLE
1
Pour Version de 6 Lumieres seulement: passer le cordon dans la tige et visser à l'ensemble de douille.
2
Faites passer le cordon à travers la pivot et boucle de luminaire, puis visser la tige à le pivot et le boucle de luminaire sur le cadre.
3
Installez les tubes de bougies par les glisser sur les douilles.
4
Installez les adeptes bougies en les plaçant au-dessus des tubes de bougie.
5
Visser l’ampoules dans les douilles. Reportez-vous à l'étiquette sur la douille de la lampe pour obtenir des informations Max Puissance.
6
Suivez les instructions d'installation de suppléments fermés pour l'installation électrique et le luminaire sur une boîte de jonction.
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c.
1A 6
2
BUCLE DE LA LAMPARA
MARCO PIVOTE
2
5
BOMBILLA
4
SEGUIDOR DE LA VELA
3
TUBO DE LA VELA
TALLO
ENCHUFE
1 ASAMBLEA DEL ENCHUFE
1
Para Versión de 6 luz Solamente: Alimente el cable a través del tallo y atornillarlo a la asamblea del enchufe.
2
Pase el cable a través del pivote y bucle de la lámpara, a continuación, atornillar el tallo al pivote y el bucle de la lámpara en el marco.
3
Instale los tubos de la vela por el deslizamiento de ellos en los enchufes.
4
Instalar los seguidores de vela por su inclusión en la parte superior de los tubos de vela.
5
Atornille las bombillas en los enchufes. Consulte la etiqueta del enchufe de la lámpara para obtener información Max Potencia.
6
Siga las instrucciones de instalación de suplementos cerrados para la instalación eléctrica y el accesorio sobre la caja de junctura.
1. Installation Instructions for. Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box. Install the candle tubes by slipping them over the socket. Install the candle followers by placing t
Atornille las bombillas en los enchufes. Consulte la etiqueta del casquillo de la lámpara para obtener información Max. Potencia. 1. 2. 3. BOMBILLA. 4.
DeWitt 4 Light Foyer Chandelier. 1.0. F3072-4. Chandelier. F3072/4. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed ...
These fixtures are intended to be installed utilizing NEC compliant junction boxes. This product is safety listed for dry locations only. This product may be dimmed with a standard incandescent dimmer. This instruction shows a typical installation. 1
Installez les bras de luminaire à le cadre de luminaire et fixez-les ensemble à l'aide des vis de luminaire. Installer les tubes de bougie en les glissant à travers ...
2016 Feiss.All rights reserved.The "Feiss" graphic is a registered trademark of Feiss. Feiss reserves the right to change specifications for product improvements ...
the needle bar (see page 16). Try test-sewing with a scrap of the fabric you are going to use and find the best settings. * When threading upper looper with wooly ...
Hamlet 1, 2, 3, and 4 Light Vanity Strip. 1.0. V 2250_. S. V 22501, V 22502,. S. S. V 22503, V 22504. S. S. Secure the mounting plate to the junction box. Connect the fixture ground wire to a suitable ground in accordance to local electrical codes. C
Conecte el cable blanco de la lámpara al cable de energía de la línea neutral con un tapón de alambre. Conecte el cable negro de la lámpara al cable de alimentación de línea caliente con un tapón de alambre. Monte el base de la lámpara en la placa de
Insert the crystal into the cover and secure it to the shade base using the washers and screws. Repeat for multiple crystals. Place the shade and spacer onto the ...
Fije la placa de montaje a la caja eléctrica con los dos tornillos de la placa de montaje. ... Conecte el cable blanco de la lámpara al cable de energía de la línea ...
Place the shade and spacer over the socket, then secure them in place by screwing the shade collar nut onto the socket; repeat for remaining sockets. Screw the ...
... socket and secure it in place by screwing the collar nut onto the socket using the shade tool. Repeat for multiple shades. Screw the lamp(s) into the socket(s).
registered trademark of Feiss. Feiss reserves the right to change specifications for product improvements without notification. A Generation Brands Company.
Connect the black fixture wire to the hot power line wire with a wire nut. Mount the fixture base onto the mounting plate and secure it with the fixture screws using ...
Place the shade and spacer over the socket, then secure them in place by tightening the collar nut using the shade tool; repeat for remaining ... 5. 6. FIXTURE SCREW. 5. Wall. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be ins
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. SOCKET. M
Colby 1, 2, 3, and 4 Light Vanity Strip. 1.1. VS4000_. Wall. VS4000_. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing NEC compliant junction boxes. This product is safety listed for damp locations. This prod
5. 6. 7. COLLAR NUT. Secure the mounting plate to the junction box. ... Place the shade over the socket and secure it in place by screwing the collar nut onto the ...
Connect the black fixture wire to the hot power line wire with a wire nut. Mount the fixture base onto the mounting plate and secure it with the fixture screws using an Allen wrench. Place the shade and spacer over the socket, then secure them in pla
Coloque la base de la lámpara en los esparragos de montaje y seguro en su lugar atornillando las tuercas capuchon en los esparragos. Atornille las en los ...
Conecte el cable negro de la lámpara al cable de alimentación de línea caliente con un tapón de alambre. Monte el base de la lámpara en la placa de montaje y fíjela con los tornillos de la lámpara. Instale el tubo de vela lo deslizándose a través del
F2997-3_F2998-5_F2999-9. Chandelier. F2997/3, F2998/5,. F2999/9. G. P. I. : ENERAL ... Refer to the label on the lamp socket for Max Wattage information.
