Connect the black fixture wire to the hot power line wire with a wire nut. Mount the fixture base onto the mounting plate and secure it with the fixture screws using ...
Vanity Strip GENERAL PRODUCT INFORMATION: This product is listed by one of the following “Nationally Recognized Testing Laboratory”
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
This product is suitable for damp locations.
Use minimum 90°c supply conductors.
This product may be dimmed with a standard incandescent dimmer. This instruction shows a typical installation.
1A
MOUNTING PLATE
1 3
JUNCTION BOX
SOCKET
4
6
1 MOUNTING PLATE SCREW
5
SHADE FIXTURE SCREW
ALLEN WRENCH SPACER COLLAR NUT
7
LAMP
1
Secure the mounting plate to the electrical box with the two mounting plate screws.
2
Connect the fixture ground wire to a suitable ground in accordance to local electrical codes.
3
Connect the white fixture wire to the neutral power line wire with a wire nut.
4
Connect the black fixture wire to the hot power line wire with a wire nut.
5
Mount the fixture base onto the mounting plate and secure it with the fixture screws using an Allen wrench.
6
Place the shade and spacer over the socket, then secure them in place by screwing the shade collar nut onto the socket. Repeat for multiple shades.
7
Screw the lamp(s) into the socket(s). Refer to the label on the lamp socket for Max Wattage information.
1
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c.
1A PLAQUE DE MONTAGE
1 3
BOÎTE JONCTION
DOUILLE
4
6
1 VIS DE MONTAGE
5
ABAT-JOUR VIS DE LUMINAIRE
CLÉ ALLEN ESPACEUR ECROU DE COLLIER
7
AMPOULE
1
Fixez la plaque de montage à la boîte de jonction avec les deux vis de montage.
2
Connectez le fil de terre du luminaire à un terrain approprié conformément aux codes électriques locaux.
3
Connectez le fil blanc du luminaire au fil de ligne à neutre avec un écrou de fil.
4
Connectez le fil noir du luminaire au fil ligne électrique chaud avec un serre-fils.
5
Montez la base de luminaire sur la plaque de montage et le fixer avec les vis de luminaire à l'aide d'une clé Allen.
6
Placez l'abat-jour et l'espaceur sur le douille, puis fixez-les en place en vissant l'écrou de collier sur la douille. Répétez l'opération pour plusieurs abat-jour.
7
Visser la/les ampoule (s) dans la/les douille (s). Reportez-vous à l'étiquette sur la douille de la lampe pour obtenir des informations Max Puissance.
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c.
1A PLACE DE MONTAJE
1 3 CAJA CONEXIONES ENCHUFE
4
6
1 TORNILLO DE MONTAJE
5
PANTALLA TORNILLO DE LA LÁMPARA
LLAVE DE ALLEN ESPACIADOR TUERCA DE COLLAR
7
BOMBILLA
1
Fije la placa de montaje a la caja de juntura con los dos tornillos de la placa de montaje.
2
Conecte el cable de tierra a una tierra artefacto adecuado de acuerdo a los códigos eléctricos locales.
3
Conecte el cable blanco de la lámpara al cable de energía de la línea neutral con un tapón de alambre.
4
Conecte el cable negro de la lámpara al cable de alimentación de línea caliente con un tapón de alambre.
5
Monte la base de la lámpara en la placa de montaje y fijarlo con los tornillos la lámpara con una llave Allen.
6
Coloque la pantalla y el espaciador sobre el enchufe, luego fijarlos en su lugar atornillando la tuerca de pantalla en el enchufe. Repita el procedimiento para múltiples pantallas.
7
Atornille la(s) bombilla(s) en la(s) enchufe(s). Consulte la etiqueta del casquillo de la lámpara para obtener información Max Potencia.
Connect the black fixture wire to the hot power line wire with a wire nut. Mount the fixture base onto the mounting plate and secure it with the fixture screws using an Allen wrench. Place the shade and spacer over the socket, then secure them in pla
Hamlet 1, 2, 3, and 4 Light Vanity Strip. 1.0. V 2250_. S. V 22501, V 22502,. S. S. V 22503, V 22504. S. S. Secure the mounting plate to the junction box. Connect the fixture ground wire to a suitable ground in accordance to local electrical codes. C
Conecte el cable blanco de la lámpara al cable de energía de la línea neutral con un tapón de alambre. Conecte el cable negro de la lámpara al cable de alimentación de línea caliente con un tapón de alambre. Monte el base de la lámpara en la placa de
registered trademark of Feiss. Feiss reserves the right to change specifications for product improvements without notification. A Generation Brands Company.
Place the shade and spacer over the socket, then secure them in place by tightening the collar nut using the shade tool; repeat for remaining ... 5. 6. FIXTURE SCREW. 5. Wall. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be ins
Fije la placa de montaje a la caja eléctrica con los dos tornillos de la placa de montaje. ... Conecte el cable blanco de la lámpara al cable de energía de la línea ...
Place the shade and spacer over the socket, then secure them in place by screwing the shade collar nut onto the socket; repeat for remaining sockets. Screw the ...
... socket and secure it in place by screwing the collar nut onto the socket using the shade tool. Repeat for multiple shades. Screw the lamp(s) into the socket(s).
CAUTION - RISK OF FIRE. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. SOCKET. M
Colby 1, 2, 3, and 4 Light Vanity Strip. 1.1. VS4000_. Wall. VS4000_. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing NEC compliant junction boxes. This product is safety listed for damp locations. This prod
5. 6. 7. COLLAR NUT. Secure the mounting plate to the junction box. ... Place the shade over the socket and secure it in place by screwing the collar nut onto the ...
V 2040_. S. Vanity Strip. 1. 6. 7. COLLAR NUT. SPACER. Secure the mounting plate to the electrical box with the two mounting plate screws. Connect the fixture ...
the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply ...
Insert the crystal into the cover and secure it to the shade base using the washers and screws. Repeat for multiple crystals. Place the shade and spacer onto the ...
Connect the white fixture wire to the neutral power line wire with a wire nut. ... Place the shade onto the socket and secure it in place by screwing the collar nut ...
Conecte el cable de tierra a una tierra artefacto adecuado de acuerdo a los códigos eléctricos locales. Conecte el cable blanco del portalámparas al cable de energía de la línea neutral con un tapón de alambre. Conecte el cable negro del portalámpara
3-LIGHT VANITY. 1. ATTACH YOUR RECEIPT HERE. Serial Number. Purchase Date. Questions, problems, missing parts? Before returning to your retailer, call ...
Connect the black fixture wire to the hot power line wire with a wire nut. Mount the fixture base onto the mounting plate and secure it with the fixture screws. Install the candle tube by slipping through socket. Place the lamp into the socket. Refer
Coloque la base de la lámpara en los esparragos de montaje y seguro en su lugar atornillando las tuercas capuchon en los esparragos. Atornille las en los ...
1. Installation Instructions for. Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box. Install the candle tubes by slipping them over the socket. Install the candle followers by placing t
Screws the lamp into the sockets. Refer to the label on the socket for Max Wattage information. ... 7400 Linder Ave, Skokie, IL 160077. 800.969.3347 www.Feiss.
