Place the shade and spacer over the socket, then secure them in place by screwing the shade collar nut onto the socket. Repeat for all shades. Screw the lamps ...
Chandelier GENERAL PRODUCT INFORMATION: These fixtures are intended to be installed utilizing NEC compliant junction boxes.
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
This product is safety listed for dry locations only. This product may be dimmed with a standard incandescent dimmer.
Use minimum 90°c supply conductors.
This instruction shows a typical installation.
1A 1
LAMP
3 2
COLLAR NUT SPACER SHADE SOCKET
1
Follow enclosed supplement installation instructions for electrical and fixture installation onto the junction box.
2
Place the shade and spacer over the socket, then secure them in place by screwing the shade collar nut onto the socket. Repeat for all shades.
3
Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information.
1
MISE EN GARDE - RISQUE D'INCENDIE Ce produit doit être installé selon le code d’installation pertinent , par une personne qui connaÎt bien le produit et son fonctionnement ainsi que les risques inhérents
Les fils d’alimentation doivent convenir pour 90°c.
1A 1
AMPOULE
3 2
ECROU DE COLLIER ESPACEUR ABAT-JOUR DOUILLE
1
Suivez les instructions d'installation de suppléments fermés pour l'installation électrique et appareil sur une boîte de jonction.
2
IPlacez l'abat-jour et l'espaceur sur le douille, puis fixez-les en place en vissant l'écrou de collier sur la douille. Répétez l'opération pour plusieurs abat-jour.
3
Visser les ampoules dans les douilles. Reportez-vous à l'étiquette sur la douille de la lampe pour obtenir des informations Max Puissance.
2
ADVERTENCIA - RIESGO DE INCENDIO Este productor debe ser instalado segun el codigo de instalacion aplicable por una persona que conozca la constussion y el funcionamiento del producto y los riesgos que supone.
Conductores de alimentacion 90°c Min.
1A 1
BOMBILLA
3 2
TUERCA DE COLLAR ESPACIADOR PANTALLA ENCHUFE
1
Siga las instrucciones de instalación de suplementos cerrados para la instalación eléctrica y el accesorio sobre la caja de conexiones.
2
Coloque la pantalla y el espaciador sobre el enchufe, luego fijarlos en su lugar atornillando la tuerca de pantalla en el enchufe. Repita el procedimiento para múltiples pantallas.
3
Atornille las bombillas en las enchufes. Consulte la etiqueta del casquillo de la lámpara para obtener información Max Potencia.
P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing NEC compliant junction boxes. This product is safety listed for dry locations only. This product ... Place the shade and spacer over the socket, then secure them
Reportez-vous à l'étiquette sur la douille de la lampe pour obtenir des informations. Max Puissance. 1. 2. 3. ABAT-JOUR. DOUILLE. AMPOULE. ECROU DE ...
Follow enclosed supplement installation instructions for electrical and fixture installation onto the junction box. Place the shade and spacer over the socket, then ...
This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors. SMALL ORNAMENT. THUMB SCREW. 7. F
the applicable installation code by a person familiar with the construction and ... Jonah 9 Light Chandelier. 1.0. F2987-9. Chandelier. F2987/9. LAMP. STEM.
Refer to the label on the lamp socket for Max Wattage information. Repeat steps 1-3 for remaining sockets. Using the help of another person, connect the upper ...
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box. Screw the finial onto the bottom of the fixture. 1. 2.
2016 Feiss.All rights reserved.The "Feiss" graphic is a registered trademark of Feiss. Feiss reserves the right to change specifications for product improvements ...
F2997-3_F2998-5_F2999-9. Chandelier. F2997/3, F2998/5,. F2999/9. G. P. I. : ENERAL ... Refer to the label on the lamp socket for Max Wattage information.
Installer l'abat-jour en le plaçant sur la ampoule. Répétez les étapes 3 à 5 pour les douilles restants. Reportez-vous aux instructions pour supplément clos ...
the applicable installation code by a person familiar ... Screw the threaded nipple to the top of the fixture, place the nipple cover over the threaded nipple, and ...
Pasar los cables de la lámpara a través del dosel y atornille el dosel en la asamblea de tallo. Conecte la lámpara a una tierra apropiada de acuerdo a los ...
jonction. Suspendez les cristaux comme indiqué sur le dessin. Se référer au tableau de cristal pour l'identification de cristal. DOUILLE. BOUCLE DE LUMINAIRE.
Place the shade onto the socket and secure it in place by screwing the collar nut ... de suplementos cerrados para la instalación eléctrica y el accesorio sobre la ...
Allier 1 Light Chandelier. 1.1. F2952-1-F2953-1. Chandelier. F2952/1, F2953/1_. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be ...
Selon votre choix de montage (chaîne ou semi-encastré), suivez les instructions d'installation de suppléments fermés pour l'installation électrique et appareil sur ...
Feed the cord through the stem and screw it onto the socket assembly. Assemble the spun pan by securing ... CAUTION - RISK OF FIRE. This product must be ...
Summerdale 3 Light Island. 1.1. F2982-3. Island. F2982/3. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing NEC compliant junction boxes. This product is safety listed for dry locations only. This product may
Connect the black fixture wire (round and/or smooth) to the hot power line wire with a wire ... Refer to the label on the lamp socket for Max Wattage information. 1.
Place the diffuser onto the threaded pipe and secure it in place by screwing on the finial of your choice. Secure the mounting plate to the electrical box with two ...
Determine la altura deseada de la lámpara alimentando el cable a través del dosel y moviendo el cable hacia arriba o hacia abajo. Coloque el cable entre las ...
