In Alaska, the warranty excludes the cost of shipping or service to your home or office. Some states do not allow the exclusion or limitation of incidental or ...
Your new GE icemaker water filter comes complete with all the necessary hardware for installation. Each filter gives you up to six months of great-tasting water. Filter should be changed after 6 months of use. REQUIRED TOOLS FOR INSTALLATION
OPTIONAL TOOLS FOR INSTALLATION
• a tube cutter • a knife • a bucket or pan
• a file • sandpaper System is Tested and Certified by NSF International against NSF/ANSI Standard 42 for the reduction of Chlorine Taste and Odor and Particulate Class V.
Do not use where water is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.
WARNING
Small parts remaining after the installation could be a choke hazard. Discard safely.
The GXRTDR has been tested and Certified by WQA according to CSA B483.1.
SPECIFICATIONS • This System has been tested according to NSF/ANSI 42 for reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 42. • Actual performance may vary with local water conditions. Model GXRTDR
Option 2: For connection to secondary filtered water faucet. NOTE: For use with FXUTC or FXULC (rev. 2) filter elements. □ See Required Parts for Installation ...
warning device, such as a tag, to the service panel. Questions? Call GE Appliances Answer Center at 800.626.2000 or Visit our Website at: GEAppliances.com.
mount adjacent (within 2 feet) to any range, cooktop, gas oven, or other microwave .... Remove everything out of the microwave oven, including packing, Owner's ...
gas oven, or other microwave. • This product is to be installed 3 feet above floor level. • Do not alter or modify any part of this kit or the oven. • For easier ...
instructions with the Consumer. • Note to Consumer – Keep these instructions for future reference. • Product failure due to improper installation is not covered ...
under the specific models as labeled on this unit. IMPORTANT — Use this oven only for its intended purpose. Never use the oven for warming or heating a room.
Minimum cabinet cutout depth from the back of the rear trim to the back finished ..... will be covered by the top cover with shelf. Hardware. Package. Top Cover.
guidelines and safety standards such as those published by the National Fire Protection. Association (NFPA), the American Society for. Heating, Refrigeration ...
Gas Association according to CAN/CGA.1.1 latest edition. When installing a gas ..... C. Install male 1/2严 or 3/4严 flare union adapter to the. NPT internal thread ...
30” Wide Range Models. 3严 Min. .... Drill 1/8严 pilot holes at a 20° angle. □ Secure the ...... Percez des trous repère de 31 mm (1/8严) à un angle de 20°.
If you are installing the cooktop in a solid surface material such as granite, quartz or any other natural or synthetic solid surface, we recommend that the cutout be ...
Any part of the cooking product which fails due to a defect in materials or workmanship. During this .... NOTE: When cleaning, take care not to come in contact.
under control knobs (if applicable), adhesive tape, wire ties, cardboard and protective plastic. Failure to remove these materials could result in damage to the.
vigueur dans votre région. Il faut prévoir ... Il est possible d'installer une hotte spéciale à proximité d'éléments ...... Si ha recibido una cocina dañada, usted debe.
wrap pipe thread tape with Teflon* around, all male. (external) pipe threads. ..... wire. Remove 4 burner attachment screws,. 2 at the front and 2 at the back. Slide.
The finished backsplash must cover the entire back wall up to the bottom of a hood, ..... Make sure the flow of combustion and ventilation air to the range is ...
trim forward, then lift up to remove. □ Find the two rear leg extension rods. Use a 1/4严 driver or wrench to adjust the left or right rear legs. □ Replace the rear ...
switch power off at service panel and lock the service disconnecting means to ..... C. Install male 1/2严 or 3/4严 flare union adapter to the. NPT internal thread of ...
rangetop has been design.certified by CSA International according to ANSI Z21.1, ..... at all burners but gas flows from only the one selected. Once air is purged ...
metal or flexible metal transition ducting cannot be used AND where a 4” diameter can be maintained throughout the entire length of the transition duct.
