Evington 2 Light Semi-Flush Mount. 1.0. SF334. SF334. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing compliant.
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
These fixtures are intended to be installed utilizing NEC compliant junction boxes.
Use minimum 90°c supply conductors.
This product is safety listed for damp locations.
1A
1
LAMP 3
3 2
THREADED PIPE
4
SHADE
WASHER HEX NUT 5
CUP FINIAL
1
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box.
2
Screw the threaded pipe to the bottom of the fixture.
3
Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information.
4
Place the shade onto the threaded pipe and secure it in place with the washer and hex nut (Do not over tighten).
5
Place the cup onto the threaded pipe and secure it in place by screwing the finial onto the threaded pipe.
1
1.0
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c.
1A
1
AMPOULE 3
3 2
TUYAU FILETÉ
4
ABAT-JOUR
RONDELLE ECROU HEX 5
COUPE FLEURON
1
Suivez les instructions d'installation de suppléments fermés pour l'installation électrique et luminaire sur une boîte de sortie de la maison.
2
Vissez le tuyau fileté à l'ensemble de douille.
3
Vissez l’ampoules dans les douilles. Reportez-vous à l'étiquette sur la douille de lampe pour obtenir des informations Max Puissance.
4
Placez l'abat-jour sur le tuyau fileté et fixez-le en place avec la rondelle et écrou hexagonal (Ne pas trop serrer).
5
Placez la coupe sur le tuyau fileté et fixez-le en place en vissant le fleuron sur le tuyau fileté.
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c.
1A
1
BOMBILLA 3
3 2
TUBO ROSCADO
4
PANTALLA
ARANDELA TUERCA HEX 5
COPA
FINIAL 1
Siga las instrucciones de instalación de suplementos cerrados para la instalación eléctrica y el accesorio sobre la caja de salida de casa.
2
Enrosque el tubo roscado a la asamblea de enchufe.
3
Atornille las bombillas en los enchufes. Consulte la etiqueta en el casquillo de la lámpara para obtener información Max Potencia.
4
Coloque la pantalla sobre el tubo roscado y seguro en su lugar con la arandela y la tuerca hex (No apriete demasiado).
5
Coloque la copa en el tubo roscado y seguro en su lugar atornillando el remate en el tubo roscado.
Place the pipe cover, spacer, steel washer, rubber washer, shade, rubber washer, and steel washer onto the threaded pipe in that order, then secure them in ...
NEC junction boxes. This product is safety listed for damp locations. This instruction shows a typical installation. CAUTION RISK OF FIRE. -. This product must be ...
Connect the black fixture wire (round and/or smooth) to the hot power line ... Place the shade inside of the decorative ring and secure it in place using the tabs.
Connect the black fixture wire to the hot power line wire with a wire nut. ... Connecter le luminaire à un terrain approprié conformément aux codes électriques ...
Coloque la base de la lámpara en los esparragos de montaje y seguro en su lugar atornillando las tuercas capuchon en los esparragos. Atornille las en los ...
This product may be dimmed with a standard incandescent dimmer. ... Connecter le fil blanc de luminaire (carré et / ou rigide) pour le fil de ligne à neutre avec ...
Refer to the label on the lamp socket for Max Wattage information. Install the shade by aligning it with the fixture base, then using the thumb screws to secure ...
Place the shade and spacer over the socket, then secure them in place by tightening the collar nut. Screw the lamp into the socket. Refer to the label on the ... Conecte el cable negro de la lámpara (redonda y / o suave) al cable de la línea eléctric
Installation Instructions for. Hamlet 2 Light Semi-Flush Mount. 1.0. SF325. SF325. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be ...
FIXTURE. FIXTURE BASE. 5. 4. 5. 6. 7. 8. 8. 8. MOUNTING PLATE SCREW ... Conecte el cable blanco de la l mpara al cable de energía de la línea neutral con ...
This product is safety listed for damp locations. This product may be dimmed with a standard incandescent dimmer. This instruction shows a typical installation.
Connect the black fixture wire to the hot power line wire with a wire nut. Place the fixture ... applicable installation code by a person familiar with the construction ...
Place the rubber washer, the shade, and large washer onto the threaded pipe (in that order), then secure them in place using a hex nut. Place the decorative cup ...
registered trademark of Feiss. Feiss reserves the right to change specifications for product improvements without notification. A Generation Brands Company.
Connect the fixture to a suitable ground in accordance to local electrical codes. Connect the white fixture wire to the neutral power line wire with a wire nut. Connect the black fixture wire to the hot power line wire with a wire nut. Mount the fixt
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box. Place the fixture base over the threaded nipple and secure it in place with the cap nut. ... with the construction and operation of th
