When you open the package with a sharp tool like a cutter knife, ... Ensure that you have all required contents for complete ... and may burn you. Always make ...
Installation Instructions Model E21316-10BZ 1.Turn breakeroff for circuit on outlet where fixture is to be installed. 2.Remove mounting bracket from fixture and install to electrical box. 3.Wire fixture to wires in outlet box. Green wire is for Ground. 4.Carefully remove packaging from fixture. 5.Install fixture to bracket and tighten cap nuts so that fixture meets the wall. 6.Install inner crystal strings to metal loops on bottom of panper diagram below.It is recommended to use glove included and not touch crystal with bare fingers. 7.Install maximum 1 x 40W G9 Xenon bulbs into socket. (Caution: Xenon bulbs get very hot and may burn you. Always make sure bulbs are off for a minimum 10 minutes before handling)
factores ambientales que pueden dañar el metal. Aplique una cera de coche de alta calidad al accesorio regularmente para protegerlo de factores ambientales ...
as a pair of pliers to ensure the strain relief is property grounded to the fixture. 2)Asegúrese de que la electricidad esté DESCONECTADA en el disyuntor o caja ...
as a pair of pliers to ensure the strain relief is property grounded to the fixture. 2)Asegúrese de que la electricidad este DESCONECTADA en el disyuntor o caja ...
FABRICADO EN CHINA. Maxim Lighting International • 253 N. Vineland Ave., City of Industry, CA 91746. Energy Efficient Electronic Ballast. 11.5" Diameter,2.5" ...
Turn wall switch OFE. Switch main power OFF. Orrnscrew circuitfuse. Apage el switch de la pared. O desconecte el fusible del circuito. Apage el switch principal ...
(Foco Circular de 22 vatios). Metal Foxture. (Parte de Metal). Darn wall Switch OFF. Switch main power OFE. Or,rnscrew circuitfuse. Apage el switch de la pared.
Replace mounting screw. 5. Install bulbs. 6. All electrical contections must bain accordance with local codas, ordinances or the. National Electrical Code. DAM.
Please call our toll free number 1-844-STAR-LED, or send a copy of your original purchase receipt, proof of purchase decal from box and the bulb to our customer care center. This replacement is the sole remedy available and liability for incidental o
To begin installation first install the glass. This is accomplished by first threading screw (S) out of the bottom of the lower sphere of the fixture (R) - see. Drawing 1 ...
Using the electrical box as a template, mark and cut out a hole in the ceiling tile ... Tighten the locknuts inside the electrical box to clamp it to the support bar ...
To begin glass installation and final assemlby, first take glass (1), slip it into the glass fitter (A) by aligning slots (S) in top of glass with knobs (K) inside the glass ...
Acabado en esmalte blanco horneado, de alto brillo. El reflector se pinta después de fabricación. Disponible en longitudes de cable tandem. Acepta clavijas ...
electromagnética según las Directivas 2006/95/CE y 2004/108/CE (CE). .... para el hogar, uso industrial, uso comercial e incluso aplicaciones de iluminación.
Para registrar su accesorio, por favor visite nuestra página web: SeaGullLighting.com. Customer Care Center. 800-347-5483. SeaGullLighting.com. HC-1934FS ...
De installatie dient plaats te vinden in overeenstemming met de meest recente .... äosight jou till eleghel wil so der lyosboll. PIR. لا ننصح ... If, when you purchased any Enlite product, your supplier included a WEEE disposal fee, you should.
Read all instructions and safety information before installing your new fan. Review ... All set screws must be checked and re-tightened where necessary before ...
To prevent severe shock or electrocution, always turn power OFF at the service panel before working with wiring. • Use this device with copper or copper-clad ...
Next, slip the glass ring (2) inside of the brackets (B) and over the lip. (L) on roof (R). Now align the holes (H) in brackets (B) with the threaded holes (T) in glass ...
