Using the electrical box as a template, mark and cut out a hole in the ceiling tile ... Tighten the locknuts inside the electrical box to clamp it to the support bar ...
Read all instructions and safety information before installing your new fan. Review ... All set screws must be checked and re-tightened where necessary before ...
Made in China. W-433. 052815. WARRANTY INFORMATION. This Westinghouse Lighting Fixture is warranted against defects in material and workmanship for a period of Five Years from ... Cette garantie ne porte ni sur les dommages survenant suite à une cata
Before you begin installing the fan, switch power off at service panel and lock ..... Fan Off â When you press the âOFFâ key, you will hear 4 short beep sounds ...
Installation work and electrical wiring must be done by qualified person(s) in ... The appliance is not intended for use by young children or infirmed persons ...
Clear the installation site of any insulation, wiring and existing lightweight bar hanger (figure 1). Remove wiring from the sides of the joist. 2. Determine if you ...
Check to make sure the screws which attach the fan blade holder to the motor are tight. 3. Some fan motors are sensitive to signals from Solid State variable ...
Clear the installation area of insulation, wiring and existing lightweight bar hanger. Remove wire attached to the side of the joist where Saf-T-Brace® will attach.
All set screws must be checked and re-tightened where necessary before installation. 17. ..... Use only a soft brush or lint-free cloth to avoid scratching the finish.
Please call our toll free number 1-844-STAR-LED, or send a copy of your original purchase receipt, proof of purchase decal from box and the bulb to our customer care center. This replacement is the sole remedy available and liability for incidental o
To begin installation first install the glass. This is accomplished by first threading screw (S) out of the bottom of the lower sphere of the fixture (R) - see. Drawing 1 ...
To begin glass installation and final assemlby, first take glass (1), slip it into the glass fitter (A) by aligning slots (S) in top of glass with knobs (K) inside the glass ...
Acabado en esmalte blanco horneado, de alto brillo. El reflector se pinta después de fabricación. Disponible en longitudes de cable tandem. Acepta clavijas ...
electromagnética según las Directivas 2006/95/CE y 2004/108/CE (CE). .... para el hogar, uso industrial, uso comercial e incluso aplicaciones de iluminación.
Para registrar su accesorio, por favor visite nuestra página web: SeaGullLighting.com. Customer Care Center. 800-347-5483. SeaGullLighting.com. HC-1934FS ...
De installatie dient plaats te vinden in overeenstemming met de meest recente .... äosight jou till eleghel wil so der lyosboll. PIR. لا ننصح ... If, when you purchased any Enlite product, your supplier included a WEEE disposal fee, you should.
To prevent severe shock or electrocution, always turn power OFF at the service panel before working with wiring. • Use this device with copper or copper-clad ...
factores ambientales que pueden dañar el metal. Aplique una cera de coche de alta calidad al accesorio regularmente para protegerlo de factores ambientales ...
Next, slip the glass ring (2) inside of the brackets (B) and over the lip. (L) on roof (R). Now align the holes (H) in brackets (B) with the threaded holes (T) in glass ...
as a pair of pliers to ensure the strain relief is property grounded to the fixture. 2)Asegúrese de que la electricidad esté DESCONECTADA en el disyuntor o caja ...
as a pair of pliers to ensure the strain relief is property grounded to the fixture. 2)Asegúrese de que la electricidad este DESCONECTADA en el disyuntor o caja ...
FABRICADO EN CHINA. Maxim Lighting International • 253 N. Vineland Ave., City of Industry, CA 91746. Energy Efficient Electronic Ballast. 11.5" Diameter,2.5" ...
