Conectar el cable verdee tierra al cable desnudo y montar con los tornillos a la caja. Después de terminar la instalación, el disositivo LED parpadeará hasta que ...
To install: Connect wires per wiring diagram as follows: • Remove pre-stripped insulation on device wires. • Strip wires in box 1/2”. • Twist ends of stripped wires together as per schematic. • Twist on wire connectors clockwise until secure. • Connect green ground wire to bare wire, and mount to box with screws. After completing successful installation LED on device will blink until programmed. For detailed programming instructions for your switch, refer to the ASPIRE RF manual that is included with the Handheld (RFHDCSG) or Table Top (RFTDCSG) Controller.
Neutral Neutre Neutro
White Blanc Blanco
Black Noir Negro
Hot Phase Vivo
(Ground) Green (Terre) Verte (Tierre) Verde
Pour Installer: Branchez les fils conformément au diagramme de câblage de la façon suivante: • Enlevez l’isolant pré-dénudé des fils de l’appareil. • Dénudez les fils de la boîte sur 1/2 po. • Torsadez les extrémités des fils ensemble selon le schéma. • Vissez les connecteurs par rotation bien à fond. • Raccordez le fil de terre vert au fil nu etmountez sur la boîte à l’aide de vis. Aprés une installation réussie, le voyant sur l’appareil clignote jusqu’à la programmation. Les instructions de programmation détaillées de votre interrupteur se trouvent à la notice de l’ASPIRE RF qui est comprise avec l’inité de commande portable (RFHDCSG) ou celle de table (RFTDCSG). Instalación: Conecte los cables de acuerdo al diagrama de alambrado siguiendo estas indicaciones: • Quite el aislamieno previamente pelado de los cables del dispositivo. • Desforre 1/2 pulgada de los cables de la caja. • Junte los extremos de los cables pelados y tuérzalos degún el disgrama esquemático. • Atornille los connectores de cables torciéndolos en el sentido horario hasta que queden fijos. • Conectar el cable verdee tierra al cable desnudo y montar con los tornillos a la caja. Después de terminar la instalación, el disositivo LED parpadeará hasta que sea programado. Para obtener instrucciones detalladas para programmar su interruptor, consulte el manual ASPIRE RF que se incluye con el controlador portátil (RFHDCSG) o de mesa (RFTDCSG) .
Fije la placa de montaje a la caja eléctrica con dos tornillos de montaje. ... cable negro de la lámpara (redonda y / o suave) al cable de la línea eléctrica caliente ...
Sub-Zero, Sub-Zero & Design, Sub-Zero & Snowflake Design, Dual Refrigeration, The Living Kitchen, Great American Kitchens The Fine Art of Kitchen Design, ...
For VMTK272, predrill 4 holes marked A with a 1/16" drill bit. For VMTK302, predrill 4 holes marked B with a 1/16" drill bit. 3. Remove template from the cabinet.
verticalement ; voir l'illustration ci-dessus. Vérifier si la dent manquante est orientée vers le haut. Trouver le bouchon au centre du corps de la valve et l'espaceur.
encounter any installation or performance problems, please don't hesitate to contact us. Our phone numbers and website are listed on the back cover. Thanks ...
Assurez-vous que l'appareil dans la boîte soit en bonne condition et que toutes ... Check whether the power supply matches your power output to avoid damage.
Before adding any oils, aromatic therapies, or skin care .... NOTE: If two steam heads are required, ensure there is at least 12-1/2â³ (31.8 cm) between the center ...
Pour ajuster l'alignement, déplacer l'adaptateur à cannelures jusqu'à atteindre l'alignement désiré. Attacher la poignée à la valve à l'aide de la vis et la rondelle.
90№ JUNCTIONS. 17. JonCtions à 90° / uniones De 90°. SWEEPS - SWK. 18. CouRBes à GRanD RaYon - swk / CuRvas - swk. SWEEPS - FASLOCK. 19 ...... 29. cEIlInG moUntInGs. montaGEs au plafond / cmontajEs En El tEcho. UnDErFloor moUntInGs. montaGEs sous pla
Features and specifications are subject to change at any ... Conditioning Engineers (ASHRAE), and the ...... Pour obtenir le nom du centre de service Wolf.
Español, página “Español-1”. K–10411. K–10412. K–10413 ... O-ring over the faucet supply hoses and place into the groove in the underside of the faucet body ...
Drive the anchor through the material .... Use a Torx drive to partially insert a #8 x 1/2" screw into the .... Insert the outer end of each trim strip behind the vertical.
2. For VMTK272, predrill 4 holes marked A with a 1/16" drill bit. For VMTK302, predrill 4 holes marked B with a 1/16" drill bit. 3. Remove template ... 2. E. Basic Specifications. Microwave Oven. Built-In Custom Trim Kits ...... viking Range, LLC.
with the washer and nut on the inside edge. For one piece toilet installations, the lower end of the lift rod should point toward the front of the tank. For two piece ...
perçage (figure 1). 2. (Optionnel) Si vous désirez passer les câblages par la surface d'installation, percez un trou pour le câble selon le gabarit de perçage.
the back cover. Thanks again for choosing Kohler Company. Before You Begin. CAUTION: Risk of fresh water contamination. This faucet contains important back-siphonage protection. Do not ... Turn the ring so the screws are to the front and back of the
a revolutionary cable management system that provides exceptional strength combined with the flexibility to adapt easily to field requirements. installation is ...... to building steel or the facility grounding system every 50'-60'. By bonding the tr
Association (CSA) for natural or LP gases. .... A slight rocking motion may be .... The Living Kitchen, Great American Kitchens The Fine Art of Kitchen Design, ...Falta(n):
Tubing cutter. • 3' of 1/4" OD copper, braided stainless steel, or PEX tubing. • Saddle valve. • Material to protect home, flooring, and cabinetry during installation.
