GM SILAO
LIQUID APPLIED SOUND DEADENER PROJECT #128650 DRAWING SERIES #7183
MECHANICAL DRAWINGS Paintshop Automation Group
Y R A N S I S M E I C L E O R R P P N I GENERAL MOTORS - SILAO ASSEMBLY PLANT LINE 1 LIQUID APPLIED SOUND DAMPENING INDEX SHEET
DESCRIPTION / TITLE
DRAWING SHEET INDEX MAJOR COMPONENTS LIST
MECHANICAL ASSEMBLY DRAWINGS
FANUC DWG. NO. SHT NO.
SYSTEM OVERVIEW SYSTEM PLAN VIEW SYSTEM END VIEW - SECTION A SYSTEM END VIEW - SECTION B SYSTEM ELEVATION VIEW - SECTION C SYSTEM ELEVATION VIEW - SECTION D EQUIPMENT PLACEMENT LAYOUT - PLAN VIEW CAMERA & LIGHTING PLACEMENT LAYOUT ROBOT, VEHICLE & CARRIER LAYOUT
DT-7183-002 DT-7183-002 DT-7183-002 DT-7183-002 DT-7183-002 DT-7183-002 DT-7183-002 DT-7183-002 DT-7183-002 DT-7183-002 DT-7183-002
1 2 3 4 5 6 7 8 9 10 11
ROBOT CLEAR SWITCH PLACEMENT LAYOUT
DT-7183-012
1
CABLE TRAY LAYOUT ~ PLAN VIEW CABLE TRAY LAYOUT ~ END VIEW
DT-7183-022 DT-7183-022
1 2
D.C.S. SAFETY LAYOUT ~ PLAN VIEW D.C.S. SAFETY LAYOUT ~ PLAN VIEW D.C.S. SAFETY LAYOUT ~ END VIEW D.C.S. SAFETY LAYOUT ~ PER ROBOT
DT-7183-052 DT-7183-052 DT-7183-052 DT-7183-052
1 2 3 4
RAIL POSITIONING LAYOUT OVERVIEW RAIL POSITIONING LAYOUT ~ PLAN VIEW RAIL POSITIONING LAYOUT ~ END VIEW
RAIL POSITIONING LAYOUT ~ DEVIATION VALUES RAIL POSITIONING LAYOUT ~ CERTIFICATION SHEET RAIL RISER POSITIONING LAYOUT
DT-7183-222 DT-7183-222 DT-7183-222 DT-7183-222 DT-7183-222 DT-7183-222
1 2 3 4 5 6
M-710iC/20L LASD ROBOT DRESS-OUT
DT-7183-322
1
PNEUMATIC SCHEMATIC PER CELL PNEUMATIC SCHEMATIC PER ROBOT CAMERA & LED LIGHT SHUTTER PNEUMATIC SCHEMATIC SEALANT & TEMPERATURE SCHEMATIC
DA-7183-002 DA-7183-002 DA-7183-002 DA-7183-002
1 2 3 4
DESCRIPTION / TITLE
MECHANICAL ASSEMBLY DRAWINGS
FANUC DWG. NO. SHT NO.
DESCRIPTION / TITLE
FANUC DWG. NO. SHT NO.
RAIL RISER - ASSEMBLY RAIL RISER -BILL OF MATERIAL RAIL RISER - DETAIL RAIL RISER - DETAIL
DO-7183-212 DO-7183-212 DO-7183-212 DO-7183-212
1 2 3 4
SAFETY FENCE - DETAIL SAFETY FENCE - DETAIL SAFETY FENCE - DETAIL SAFETY FENCE - DETAIL
DO-7183-602 DO-7183-602 DO-7183-602 DO-7183-602
22 23 24 25
M-710iC/20M LASD HOSE CONTAINMENT - ASSEMBLY
M-710iC/20M LASD HOSE CONTAINMENT - BILL OF MATERIAL M-710iC/20M LASD HOSE CONTAINMENT - BILL OF MATERIAL
DO-7183-322 DO-7183-322 DO-7183-322
1 2 3
LASD HOSE MANAGEMENT - ASSEMBLY LASD HOSE MANAGEMENT - BILL OF MATERIAL
DO-7183-612 DO-7183-612
1 2
BULK SUPPLY HOSE CONTAINMENT - ASSEMBLY BULK SUPPLY HOSE CONTAINMENT - BILL OF MATERIAL BULK SUPPLY HOSE CONTAINMENT - DETAIL BULK SUPPLY HOSE CONTAINMENT - DETAIL
DO-7183-312 DO-7183-312 DO-7183-312 DO-7183-312
1 2 3 4
LASD TROLLEY HOSE SUPPORT - ASSEMBLY LASD TROLLEY HOSE SUPPORT - ASSEMBLY LASD TROLLEY HOSE SUPPORT - BILL OF MATERIAL LASD TROLLEY HOSE SUPPORT - DETAIL LASD TROLLEY HOSE SUPPORT - DETAIL LASD TROLLEY HOSE SUPPORT - DETAIL
DO-7183-642 DO-7183-642 DO-7183-642 DO-7183-642 DO-7183-642 DO-7183-642
1 2 3 4 5 6
LASD MSA EOAT L.H. - ASSEMBLY LASD MSA EOAT L.H. - BILL OF MATERIAL LASD MSA EOAT L.H. - DETAIL LASD MSA EOAT L.H. - DETAIL
DO-7183-512 DO-7183-512 DO-7183-512 DO-7183-512
1 2 3 4
LASD WATER BATH STAND - ASSEMBLY LASD WATER BATH STAND - BILL OF MATERIAL LASD WATER BATH STAND - DETAIL LASD WATER BATH STAND - DETAIL
DO-7183-642 DO-7183-642 DO-7183-642 DO-7183-642
1 2 3 4
LASD MSA EOAT R.H. - ASSEMBLY LASD MSA EOAT R.H. - BILL OF MATERIAL LASD MSA EOAT R.H. - DETAIL
DO-7183-522 DO-7183-522 DO-7183-522
1 2 3
SAFETY FENCE LAYOUT - PLAN VIEW SAFETY FENCE LAYOUT - ELEVATION VIEWS SAFETY FENCE LAYOUT - SECTION VIEWS SAFETY FENCE LAYOUT - CABLE TRAY LAYOUT SAFETY FENCE - COMPARISON LAYOUT SAFETY FENCE - BILL OF MATERIAL SAFETY FENCE - DETAIL SAFETY FENCE - DETAIL SAFETY FENCE - DETAIL SAFETY FENCE - DETAIL SAFETY FENCE - DETAIL SAFETY FENCE - DETAIL SAFETY FENCE - DETAIL SAFETY FENCE - DETAIL SAFETY FENCE - DETAIL SAFETY FENCE - DETAIL SAFETY FENCE - DETAIL SAFETY FENCE - DETAIL SAFETY FENCE - DETAIL SAFETY FENCE - DETAIL SAFETY FENCE - DETAIL SAFETY FENCE - DETAIL
DO-7183-602 DO-7183-602 DO-7183-602 DO-7183-602 DO-7183-602 DO-7183-602 DO-7183-602 DO-7183-602 DO-7183-602 DO-7183-602 DO-7183-602 DO-7183-602 DO-7183-602 DO-7183-602 DO-7183-602 DO-7183-602 DO-7183-602 DO-7183-602 DO-7183-602 DO-7183-602 DO-7183-602 DO-7183-602
1 2 3 ND 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
NO. No.
DESCRIPTION
THE FOLLOWING EQUIPMENT IS TO BE PROVIDED BY THE INSTALLATION CONTRACTOR:
1. CABLE TRAY, LOW (ON FLOOR FOR ROBOT CABLES) 2. CABLE TRAY, HIGH (ON TOP OF FENCING FOR SYSTEM CABLES) 3. MATERIAL HEADER PIPING, HANGERS & MISC. FITTINGS & HARDWARE 4. BRACKETS & MOUNTING HARDWARE FOR BODY I.D. PHOTO-EYES, MUTING SWITCHES & DOOR OPEN DETECTION PHOTO-EYES. 5. COMPRESSED AIR HEADER, PIPING, FITTINGS TO AUTOMATION & DISPENSE EQUIPMENT AIR DROPS. 6. ANCHORS FOR FENCING, CAMERA STANDS, LED LIGHT STANDS, ETC.
BC
= PROVIDED BY INSTALL CONTRACTOR
NOTE: QUANTITIES SHOWN IN LIST ARE FOR LINE 1 ONLY
DATE FECHA
KEY PLAN SCALE: NONE
NOTA: ESTE DIBUJO (PLANO) Y SU CONTENIDO ES PROPIEDAD DE
GENERAL MOTORS DE MEXICO, S.A. DE C.V. POR NINGUN MOTIVO DEBE SER REPODUCIDO DE FORMA ALGUNA, TAMPOCO SUMINISTRADO A ENTIDAD EXTERNA PARA SER EXAMINADO, SIN EL CONSENTIMIENTO PREVIO DE LA PROPIETARIA. ESTE DIBUJO (PLANO) SOLO DEBERA SER UTILIZADO COMO REFERENCIA O MEDIO PARA DESARROLLAR EL TRABAJO CONTRATADO. LA VIOLACION DE LO ANTES MENCIONADO PUEDE ACARREAR RESPONSABILIDAD PENAL DE ACUERDO A LO PREVISTO POR LA LEY FEDERAL DE LOS DERECHOS DE AUTOR. C
MEXICO
General Motors Corporation MEXICAN TRUCK ASSEMBLY FACILITY GM de MEXICO CAD DATA. AVOID MANUAL CHANGES DO NOT SCALE DRAWING THE FOLLOWING ITEMS APPLY UNLESS OTHERWISE SPECIFIED: ALL GEOMETRIC DIMENSIONING AND TOLERANCING TO BE INTERPRETED PER THE AMERICAN NATIONAL STANDARD ANSI Y14.5M - 1982. FOR FEATURES OF SIZE, PERFECT STRAIGHTNESS NOT REQUIRED AT MMC. FOR DIAMETRAL FEATURES, ROUNDNESS MUST BE WITHIN THE MMC AND LMC (LEAST MATERIAL CONDITION) BOUNDARY. TRUE POSITION TOLERANCES, AND RELATED DATUMS (EXCEPT PLANE SURFACES), APPLY TO MMC. OTHER GEOMETRIC TOLERANCES AND RELATED DATUMS, APPLY RFS.
19 20 21
PRELIMINARY May 16, 2016
BY POR
REVISIONS REVISIONES
NORTH
INSTALLATION DRAWINGS
SEPARATE TRUE POSITION CALLOUTS MAY BE GAGED SEPARATELY, REGARDLESS OF DATUM REFERENCE.
INCH
UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS ARE IN INCHES. ALL TWO PLACE DECIMAL DIMENSIONS ±0.01 ALL THREE PLACE DECIMAL DIMENSIONS ±0.005 ALL FOUR PLACE DECIMAL DIMENSIONS ±0.0005 ALL MACHINED ANGLES ±0°-15' C'SINK ALL TAPPED HOLES. REMOVE ALL BURRS AND SHARP CORNERS. UNFINISHED CASTING AND WELDMENT DIMENSIONS ±0.12 BURNOUT DIMENSIONS ±0.12 DO NOT USE REF. DIMENSIONS FOR MANUFACTURING. DIMENSIONS IN [XX] ARE IN MILLIMETERS FOLLOW FANUC ENGINEERING STANDARDS. 125
3.2
OR BETTER ON ALL MACHINED SURFACES.
MARK PART WITH FANUC PART NO. AND REVISION LETTER THIS MATERIAL IS THE EXCLUSIVE PROPERTY OF FANUC ROBOTICS CORPORATION AND MUST BE RETURNED TO FANUC IMMEDIATELY UPON REQUEST. THIS MATERIAL AND THE INFORMATION ILLUSTRATED OR CONTAINED HEREIN MAY NOT BE REPRODUCED, COPIED, USED OR TRANSMITTED IN WHOLE OR IN PART IN ANY WAY WITHOUT THE PRIOR WRITTEN CONSENT OF FANUC.
3900 W. Hamlin Rd. Rochester Hills, Mi. 48309-3253 TITLE:
GM SILAO LASD ZONE INDEX SHEET - LINE 1
DRAWN BY CHECKED BY
DAS DAS
DATE: DATE:
APPRV'D. BY PROJ. NO.
4/19/16 4/20/16
DATE:
128650
SHEET NO.
1
SCALE:
TOTAL SHEETS
1:1
DRAWING NO.
DT- 7183-002
Y R A N S I S M E I C L E O R R P P N I GENERAL MOTORS - SILAO ASSEMBLY PLANT LINE 1 LIQUID APPLIED SOUND DAMPENING COMPONENTS LIST
MECHANICAL
JOB SPECIFIC COMPONENTS
FANUC STANDARD COMPONENTS
ELECTRICAL
RAIL RISER ASSEMBLY
DO-7183-212
2
CELL MAIN AIR W/ROSS 2" NPT LOCKOUT VALVE ASM
DO-2025-351
1
POWER DISTRIBUTION PANEL (P.D.P)
BULK SUPPLY HOSE CONTAINMENT ASSEMBLY
DO-7183-312
1
LASD TOOL DIP TANK ASSY
DO-2015-717
4
SCC
M710iC/20M ROBOT HOSE CONTAINMENT ASSEMBLY
DO-7183-322
4
LASD SLUDGE TANK/PUMP ASSY
DO-2015-773
4
-
ROBOT AIR CONTROL ASSEMBLY
DO-7183-330
4
-
-
-
-
1
MAINTENANCE CELL MAN DOOR LATCH ASSEMBLY
DO-2025-630
ECS-5391
2
ROBOT S.S. ARM MANIFOLD ASSEMBLY (M710iC-20M LASD)
DO-7183-402
4
ISOLATED TEACH TIP ASSEMBLY
DUAL MSA GUN END-OF-ARM TOOLING LH ASSEMBLY
DO-7183-512
2
M710iC/20M & M710iC/70 ROBCAL BASE
DUAL MSA GUN END-OF-ARM TOOLING RH ASSEMBLY
DO-7183-522
2
SAFETY FENCE ASSEMBLY
DO-7183-602
HOSE MANAGEMENT ASSEMBLY
ECS-4708
1
DE-7183-111
1
-
-
6
ENTRANCE & EXIT J-BOX
DO-2015-503
2
SWITCHED AUX POWER J-BOX
ECS-5332
1
DO-2025-703
2
MAINTENANCE J BOX
ECS-5393
6
M20 J1 CLEAR SWITCH ASM.
DO-2025-705
1
CAMERA & LED POWER J-BOXES
DE-7183-380
3
1
M20iA ROBCAL BASE ASM.
DO-2025-707
1
ROBOT CONTROLLER R30iB
DE-7183-401
4
DO-7183-612
4
WRIST SLIDE PLATE ASSEMBLY
DO-2025-506
4
80
OVERHEAD ROBOT CONTROLLER R30iB OPENER
DE-7183-402
1
-
8
M710iC/20L J1 AXIS CLEAR SWITCH ASM.
DO-2025-709
4
81
OVERHEAD ROBOT CONTROLLER R30iB VISION
DE-7183-403
1
HOSE SUPPORT / TROLLEY I-BEAM ASSEMBLY
DO-7183-642
1
82
PLC PANEL (10 SLOT)
GCCL 14147
1
SLUDGE PUMP AND TANK ASSEMBLY
DO-7183-702
4
83
TURCK I/O MODULE
GCCL 20015
1
WATER BATH MOUNTING STAND ASSEMBLY
DO-7183-712
4
84
ETHERNET SWITCH MODULE - 28 PORT
GCCL 21619
1
85
ETHERNET SWITCH MODULE - 16 PORT
GCCL 21626
2
86
SOLA-HD POWER SUPPLY (SCP-X SERIES)
GCCL 11520
4
87
PROX CABLE (HOOD EOAT)
DE-2020-976-002
1
CELL MAIN AIR VALVE - 2" N.P.T.
POST MOUNT SWITCH BRACKET ASSEMBLY
S.E.E. - DUAL IPS SHOTMETER w/ ENET
PURGE BUCKET ROLLER & SPRAY STAND ASSEMBLY
DO-2025-717
4
TIP DRESS SWITCH MOUNT ASSEMBLY
DO-2025-721
8
2200-1080-021
4
SHORT CALIBRATION TOOL ASSMEBLY
MO-1800-943
2
88
TRIGGER VALVE ASSEMBLY
DE-2030-262
4
SEE - 2 VALVE MSA APPLICATOR
NSE-001028
4
ADAPTER PLATE M710/R2000 - ROBCAL
MO-1800-945-002
1
89
FORTRESS "STOP" SWITCH #NO2T6ST401T03116D1GM
GCCL 70003
14
SEE - MSA METRIC NOZZLE PLATE 150MM (SPARE)
8
NSE-00772
1
VISION TARGET (FOR SMART GUN)
VO-1800-550
4
90
FORTRESS "LOK" SWITCH #NO2T6SL461T03428D1D1GM
GCCL 70006
S.E.E. - PRESSURE TRANSDUCER (FOR HEADER)
1206-499
1
L.E.D. LIGHT ASSEMBLY (RED)
VO-2015-003
10
91
FORTRESS SLIDEBAR #TG
GCCL 70001
6
GRACO - RAM UNI-DRUM LOCKOUT SAFETY
24U969
3
VISION VERIFICATION FLAT BRACKET
VO-2015-005
4
92
FORTRESS TOUNGE ACTUATOR #TK
GCCL 70004
16
GRACO - BULK SUPPLY 34:1 RH PUMP
24U643
3
CAMERA ENCLOSURE ASSEMBLY
VO-2025-004-OOO
10
93
ALLEN-BRADLEY PHOTO-EYE
42EF-P8KBC-F4
8
S.C.S. - PROTECTIVE HOSE COVER KIT
DP0130A
4
FANUC ENCODERS - 2 PER IPS
A860-2010-T341
8
94
ALLEN-BRADLEY REFLECTOR
92-118
8
5X00B9003
1
95
ALLEN-BRADLEY REFLECTOR MOUNTING BRACKET
60-2649
8
96
ALLEN-BRADLEY P.E. MOUNTING BRACKET
60-2657
8
97
ELECTRICAL CABLE FOR SHORT CALIBRATION TOOL
EE-5770-020-040
1
98
LARCO TRIM KIT
0022015200
2
99
TURCK MUTING SWITCH
Bi50U-Q80-AP6X2-H1141
8
100
LARCO SAFETY MAT 48" x 48"
LI23286911
2
101
SICK LIGHT CURTAIN #
CURTO000000025O
2
ROSS 2" N.P.T. AIR FILTER (MANUAL DRAIN) ERIND AERO-MOTIVE TROLLEY #BT34I 3.5gm PAIL (WHITE) - McMASTER
HDWMO0000573210
8
4211T61
4
BC
BODY I.D. PHOTO-EYE STAND
-
1
BC
DOOR OPEN PHOTOEYE STANDS
-
4
GigE CAMERA (BODY LOCATION)
FUJI LENS #xxxxxxxxx (BODY LOCATION)
CMRAO000000054O
X
LENSO0000000xxx
X
102
BULK SUPPLY MCP
ECS-5762
1
103
LARCO SAFETY MAT 48" x 66"
-
2
104
LARCO TRIM KIT
-
2
NO. No.
DESCRIPTION
BY POR
DATE FECHA
REVISIONS REVISIONES
NORTH
MECHANICAL
KEY PLAN SCALE: NONE
NOTA: ESTE DIBUJO (PLANO) Y SU CONTENIDO ES PROPIEDAD DE
GENERAL MOTORS DE MEXICO, S.A. DE C.V. POR NINGUN MOTIVO DEBE SER REPODUCIDO DE FORMA ALGUNA, TAMPOCO SUMINISTRADO A ENTIDAD EXTERNA PARA SER EXAMINADO, SIN EL CONSENTIMIENTO PREVIO DE LA PROPIETARIA. ESTE DIBUJO (PLANO) SOLO DEBERA SER UTILIZADO COMO REFERENCIA O MEDIO PARA DESARROLLAR EL TRABAJO CONTRATADO. LA VIOLACION DE LO ANTES MENCIONADO PUEDE ACARREAR RESPONSABILIDAD PENAL DE ACUERDO A LO PREVISTO POR LA LEY FEDERAL DE LOS DERECHOS DE AUTOR. C
MEXICO
General Motors Corporation MEXICAN TRUCK ASSEMBLY FACILITY GM de MEXICO CAD DATA. AVOID MANUAL CHANGES DO NOT SCALE DRAWING THE FOLLOWING ITEMS APPLY UNLESS OTHERWISE SPECIFIED: ALL GEOMETRIC DIMENSIONING AND TOLERANCING TO BE INTERPRETED PER THE AMERICAN NATIONAL STANDARD ANSI Y14.5M - 1982. FOR FEATURES OF SIZE, PERFECT STRAIGHTNESS NOT REQUIRED AT MMC. FOR DIAMETRAL FEATURES, ROUNDNESS MUST BE WITHIN THE MMC AND LMC (LEAST MATERIAL CONDITION) BOUNDARY. TRUE POSITION TOLERANCES, AND RELATED DATUMS (EXCEPT PLANE SURFACES), APPLY TO MMC. OTHER GEOMETRIC TOLERANCES AND RELATED DATUMS, APPLY RFS. SEPARATE TRUE POSITION CALLOUTS MAY BE GAGED SEPARATELY, REGARDLESS OF DATUM REFERENCE.
INCH
UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS ARE IN INCHES. ALL TWO PLACE DECIMAL DIMENSIONS ±0.01 ALL THREE PLACE DECIMAL DIMENSIONS ±0.005 ALL FOUR PLACE DECIMAL DIMENSIONS ±0.0005 ALL MACHINED ANGLES ±0°-15' C'SINK ALL TAPPED HOLES. REMOVE ALL BURRS AND SHARP CORNERS. UNFINISHED CASTING AND WELDMENT DIMENSIONS ±0.12 BURNOUT DIMENSIONS ±0.12 DO NOT USE REF. DIMENSIONS FOR MANUFACTURING. DIMENSIONS IN [XX] ARE IN MILLIMETERS FOLLOW FANUC ENGINEERING STANDARDS.
105
125
3.2
OR BETTER ON ALL MACHINED SURFACES.
106
MARK PART WITH FANUC PART NO. AND REVISION LETTER
107
THIS MATERIAL IS THE EXCLUSIVE PROPERTY OF FANUC ROBOTICS CORPORATION AND MUST BE RETURNED TO FANUC IMMEDIATELY UPON REQUEST. THIS MATERIAL AND THE INFORMATION ILLUSTRATED OR CONTAINED HEREIN MAY NOT BE REPRODUCED, COPIED, USED OR TRANSMITTED IN WHOLE OR IN PART IN ANY WAY WITHOUT THE PRIOR WRITTEN CONSENT OF FANUC.
108
109
110
PRELIMINARY May 16, 2016
THE FOLLOWING EQUIPMENT IS TO BE PROVIDED BY THE INSTALLATION CONTRACTOR:
1. CABLE TRAY, LOW (ON FLOOR FOR ROBOT CABLES) 2. CABLE TRAY, HIGH (ON TOP OF FENCING FOR SYSTEM CABLES) 3. MATERIAL HEADER PIPING, HANGERS & MISC. FITTINGS & HARDWARE 4. BRACKETS & MOUNTING HARDWARE FOR BODY I.D. PHOTO-EYES, MUTING SWITCHES & DOOR OPEN DETECTION PHOTO-EYES. 5. COMPRESSED AIR HEADER, PIPING, FITTINGS TO AUTOMATION & DISPENSE EQUIPMENT AIR DROPS. 6. ANCHORS FOR FENCING, CAMERA STANDS, LED LIGHT STANDS, ETC.
BC
= PROVIDED BY INSTALL CONTRACTOR
NOTE: QUANTITIES SHOWN IN LIST ARE FOR LINE 1 ONLY
3900 W. Hamlin Rd. Rochester Hills, Mi. 48309-3253 TITLE:
GM SILAO LASD ZONE MAJOR COMPONENTS - LINE 1
DRAWN BY CHECKED BY
DAS DAS
DATE: DATE:
APPRV'D. BY PROJ. NO.
4/19/16 4/20/16
DATE:
128650
SHEET NO.
2
SCALE:
TOTAL SHEETS
1:1
DRAWING NO.
DT- 7183-002
LINE 1 LASD-1
LINE 1 LASD-2
LINE 2 ISS-2 NO. No.
DESCRIPTION
BY POR
DATE FECHA
REVISIONS REVISIONES
"0.00"
NORTH
"0.00"
CARRIER
"0.00" "0.00"
CARRIER
"0.00" "0.00"
CARRIER
"0.00" "0.00"
CARRIER
"0.00" "0.00"
CARRIER
KEY PLAN SCALE: NONE
PURGE BUCKET
R4 S TO P
R
B AUTO
Y
E RGE C EM
ALARM
SYSTEM MODE
MASTER
B R1
ROBOT CONTROLLER
G
R4 RESET
R3
FAULT
ROBOT SELECT
POWER ON MASTER
G HOME
SELECTED ROBOT MOVE
A FLASH=BYPASS SELECTED ROBOT ON=HOME
BYPASS
NORMAL
SELECTED ROBOT CONVEYOR
A BYPASSED SELECTED ROBOT CONVEYOR
CANCEL
CONTINUE
SELECTED ROBOT CYCLE/E-STOP
RUN
HOLD
POWER ON
CONVEYOR
MASTER
A
B
FLASH=CONTINUE SELECTED ROBOT ON=CANCEL
PURGE ALL SUPER OFF
R-30iB
ON
CAMERA LED'S
SCC
ECS-5393
MAINT. AREA J- BOX
ECS-5393
POWER OFF
SILENCE
B PROGRAM SELECTED ROBOT RUN ERROR BYPASS
MAINT. AREA J- BOX
R
TEACH MANUAL
N
R-30iB
ECS-5393
MAINT. AREA J- BOX
ECS-5393
MAINT. AREA J- BOX
1/2" NPT AIR INLET REF.
1/2" NPT AIR INLET REF.
305 CUST.
525 CUSTOM
1025 CUSTOM
525 CUSTOM
PURGE BUCKET
GENERAL MOTORS DE MEXICO, S.A. DE C.V.
ROBOT CONTROLLER
LINE 1 LASD-2
NOTA: ESTE DIBUJO (PLANO) Y SU CONTENIDO ES PROPIEDAD DE
R2
R4
POR NINGUN MOTIVO DEBE SER REPODUCIDO DE FORMA ALGUNA, TAMPOCO SUMINISTRADO A ENTIDAD EXTERNA PARA SER EXAMINADO, SIN EL CONSENTIMIENTO PREVIO DE LA PROPIETARIA. ESTE DIBUJO (PLANO) SOLO DEBERA SER UTILIZADO COMO REFERENCIA O MEDIO PARA DESARROLLAR EL TRABAJO CONTRATADO. LA VIOLACION DE LO ANTES MENCIONADO PUEDE ACARREAR RESPONSABILIDAD PENAL DE ACUERDO A LO PREVISTO POR LA LEY FEDERAL DE LOS DERECHOS DE AUTOR. C
LINE 1 LASD-1
R2
P.D.P.
ECS-5391
EXIT INTRUSION J- BOX W/ MUTING
PLC J-BOX SOLA P/S
625 CUSTOM
1025 CUSTOM
MEXICO
General Motors Corporation MEXICAN TRUCK ASSEMBLY FACILITY GM de MEXICO CAD DATA. AVOID MANUAL CHANGES DO NOT SCALE DRAWING THE FOLLOWING ITEMS APPLY UNLESS OTHERWISE SPECIFIED:
"0.00" "0.00"
CARRIER
"0.00" "0.00"
CARRIER
"0.00" "0.00"
CARRIER
"0.00" "0.00"
CARRIER
"0.00" "0.00"
CARRIER
ALL GEOMETRIC DIMENSIONING AND TOLERANCING TO BE INTERPRETED PER THE AMERICAN NATIONAL STANDARD ANSI Y14.5M - 1982. FOR FEATURES OF SIZE, PERFECT STRAIGHTNESS NOT REQUIRED AT MMC. FOR DIAMETRAL FEATURES, ROUNDNESS MUST BE WITHIN THE MMC AND LMC (LEAST MATERIAL CONDITION) BOUNDARY. TRUE POSITION TOLERANCES, AND RELATED DATUMS (EXCEPT PLANE SURFACES), APPLY TO MMC. 625 CUSTOM
OTHER GEOMETRIC TOLERANCES AND RELATED DATUMS, APPLY RFS. SEPARATE TRUE POSITION CALLOUTS MAY BE GAGED SEPARATELY, REGARDLESS 1025 CUSTOM
OF DATUM REFERENCE.
R3
525 CUSTOM
525 CUSTOM
R1 305 CUST.
1025 CUSTOM 1/2" NPT AIR INLET REF.
MAINT. AREA J- BOX
1/2" NPT AIR INLET REF.
R-30iB
ECS-5393
MAINT. AREA J- BOX
MAINT. AREA J- BOX
R-30iB
ECS-5393
ROBOT CONTROLLER
ECS-5393
T1 "0" LINE
OF RAIL
R3
ALL DIMENSIONS ARE IN INCHES. ALL TWO PLACE DECIMAL DIMENSIONS ±0.01 ALL THREE PLACE DECIMAL DIMENSIONS ±0.005 ALL FOUR PLACE DECIMAL DIMENSIONS ±0.0005 ALL MACHINED ANGLES ±0°-15' C'SINK ALL TAPPED HOLES. REMOVE ALL BURRS AND SHARP CORNERS. UNFINISHED CASTING AND WELDMENT DIMENSIONS ±0.12 BURNOUT DIMENSIONS ±0.12 DO NOT USE REF. DIMENSIONS FOR MANUFACTURING. DIMENSIONS IN [XX] ARE IN MILLIMETERS FOLLOW FANUC ENGINEERING STANDARDS.
ECS-5393
OF RAIL
R1
125
3C3S POST
OR BETTER ON ALL MACHINED SURFACES.
THIS MATERIAL IS THE EXCLUSIVE PROPERTY OF FANUC ROBOTICS CORPORATION AND MUST BE RETURNED TO FANUC IMMEDIATELY UPON REQUEST. THIS MATERIAL AND THE INFORMATION ILLUSTRATED OR CONTAINED HEREIN MAY NOT BE REPRODUCED, COPIED, USED OR TRANSMITTED IN WHOLE OR IN PART IN ANY WAY WITHOUT THE PRIOR WRITTEN CONSENT OF FANUC.
3900 W. Hamlin Rd. Rochester Hills, Mi. 48309-3253 TITLE:
GM SILAO LIQUID APPLIED SOUND DEADENER ZONE SYSTEM OVERVIEW DRAWN BY CHECKED BY
MM. DAS
DATE: DATE:
APPRV'D. BY PROJ. NO.
ALL LOCATIONAL DIMS SHOWN ON THIS SHEET ARE FOR REFERENCE ONLY. SEE INDEX SHEET FOR EQUIPMENT SPECIFIC POSTIONING LAYOUTS.
3.2
MARK PART WITH FANUC PART NO. AND REVISION LETTER
PRELIMINARY May 16, 2015 NOTE: SYSTEM INSTALLED ON 2ND LEVEL
UNLESS OTHERWISE SPECIFIED
ROBOT CONTROLLER
T1 "0" LINE
MAINT. AREA J- BOX
3C3S POST
INCH
LINE 1 ISS-1
10/05/15 10/__/15
DATE:
128650
SHEET NO.
3
SCALE:
TOTAL SHEETS
1/48
DRAWING NO.
DT- 7183-002
5
A
6
B
NO. No.
DESCRIPTION
BY POR
C
R4 STO P
R
R-30iB ECS-5393
M
B MANUAL AUTO TEACH
Y
E
GE ER NC
MASTER
ROBOT CONTROLLER
G
R4 RESET
R3
FAULT
SELECTED ROBOT
MASTER POWER ON
G A
SELECTED ROBOT
A
A
FLASH=CONTINUE
BYPASSED
FLASH=BYPASS
SELECTED ROBOT CONVEYOR
SELECTED ROBOT ON=HOME
RUN
HOLD
POWER ON
CONVEYOR
MASTER
B PURGE ALL
SELECTED ROBOT ON=CANCEL
SUPER OFF
R-30iB
ON
CAMERA LED'S
SCC
MAINT. AREA J- BOX
ECS-5393
POWER OFF
B R1
ROBOT SELECT CYCLE/E-STOP CANCEL CONTINUE
CONVEYOR BYPASS NORMAL
SELECTED ROBOT
MAINT. AREA J- BOX
R
SILENCE ALARM
SYSTEM MODE
B RUN ERROR PROGRAM SELECTED ROBOT MOVE BYPASS HOME
ECS-5393
MAINT. AREA J- BOX
ECS-5393
MAINT. AREA J- BOX
1/2" NPT AIR INLET REF.
1/2" NPT AIR INLET REF.
525 CUSTOM
305 CUST.
525 CUSTOM
1025 CUSTOM
R4
P.D.P.
R2
ECS-5391
EXIT INTRUSION J- BOX W/ MUTING
PLC J-BOX 625 CUSTOM
1025 CUSTOM
SOLA P/S
M CARRIER
"0.00"
"0.00" "0.00"
CARRIER
"0.00"
"0.00"
M
"0.00"
CARRIER
NORTH
M
REVISIONS REVISIONES
R2 ROBOT CONTROLLER
7
DATE FECHA
KEY PLAN SCALE: NONE
M
NOTA: ESTE DIBUJO (PLANO) Y SU CONTENIDO ES PROPIEDAD DE
GENERAL MOTORS DE MEXICO, S.A. DE C.V.
1025 CUSTOM
625 CUSTOM
POR NINGUN MOTIVO DEBE SER REPODUCIDO DE FORMA ALGUNA, TAMPOCO SUMINISTRADO A ENTIDAD EXTERNA PARA SER EXAMINADO, SIN EL CONSENTIMIENTO PREVIO DE LA PROPIETARIA. ESTE DIBUJO (PLANO) SOLO DEBERA SER UTILIZADO COMO REFERENCIA O MEDIO PARA DESARROLLAR EL TRABAJO CONTRATADO. LA VIOLACION DE LO ANTES MENCIONADO PUEDE ACARREAR RESPONSABILIDAD PENAL DE ACUERDO A LO PREVISTO POR LA LEY FEDERAL DE LOS DERECHOS DE AUTOR. C
R3
MEXICO
General Motors Corporation MEXICAN TRUCK ASSEMBLY FACILITY GM de MEXICO
525 CUSTOM
525 CUSTOM
R1 1025 CUSTOM
1/2" NPT AIR INLET REF.
1/2" NPT AIR INLET REF.
R-30iB
ECS-5393
MAINT. AREA J- BOX
MAINT. AREA J- BOX
R-30iB
ECS-5393
ROBOT CONTROLLER MAINT. AREA J- BOX ECS-5393
CAD DATA. AVOID MANUAL CHANGES
305 CUST.
MAINT. AREA J- BOX
DO NOT SCALE DRAWING
ECS-5393
ROBOT CONTROLLER
R3
R1
THE FOLLOWING ITEMS APPLY UNLESS OTHERWISE SPECIFIED: ALL GEOMETRIC DIMENSIONING AND TOLERANCING TO BE INTERPRETED PER THE
D
AMERICAN NATIONAL STANDARD ANSI Y14.5M - 1982. FOR FEATURES OF SIZE, PERFECT STRAIGHTNESS NOT REQUIRED AT MMC.
8
FOR DIAMETRAL FEATURES, ROUNDNESS MUST BE WITHIN THE MMC AND LMC (LEAST MATERIAL CONDITION) BOUNDARY. TRUE POSITION TOLERANCES, AND RELATED DATUMS (EXCEPT PLANE SURFACES), APPLY TO MMC. OTHER GEOMETRIC TOLERANCES AND RELATED DATUMS, APPLY RFS. SEPARATE TRUE POSITION CALLOUTS MAY BE GAGED SEPARATELY, REGARDLESS OF DATUM REFERENCE.
INCH
UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS ARE IN INCHES. ALL TWO PLACE DECIMAL DIMENSIONS ±0.01 ALL THREE PLACE DECIMAL DIMENSIONS ±0.005 ALL FOUR PLACE DECIMAL DIMENSIONS ±0.0005 ALL MACHINED ANGLES ±0°-15' C'SINK ALL TAPPED HOLES. REMOVE ALL BURRS AND SHARP CORNERS. UNFINISHED CASTING AND WELDMENT DIMENSIONS ±0.12 BURNOUT DIMENSIONS ±0.12 DO NOT USE REF. DIMENSIONS FOR MANUFACTURING. DIMENSIONS IN [XX] ARE IN MILLIMETERS FOLLOW FANUC ENGINEERING STANDARDS. 125
3.2
OR BETTER ON ALL MACHINED SURFACES.
MARK PART WITH FANUC PART NO. AND REVISION LETTER THIS MATERIAL IS THE EXCLUSIVE PROPERTY OF FANUC ROBOTICS CORPORATION AND MUST BE RETURNED TO FANUC IMMEDIATELY UPON REQUEST. THIS MATERIAL AND THE INFORMATION ILLUSTRATED OR CONTAINED HEREIN MAY NOT BE REPRODUCED, COPIED, USED OR TRANSMITTED IN WHOLE OR IN PART IN ANY WAY WITHOUT THE PRIOR WRITTEN CONSENT OF FANUC.
M-710iC/20M
F-
-
R4
M-710iC/20M
F-
-
DUAL ARM 10.5M
ISS LINE 1
R5
M-20iA/10L
F-
-
N/A
ISS LINE 1
R6
M-710iC/70
F-
-
N/A
ECS-5391
LED POWER CAMERA POWER
P.D.P. B A
M
MUTING PHOTO-EYE TIP DRESS SWITCH MAINTENANCE SAFETY GATE SWITCH MAINTENANCE ENTRY GATE SWITCH MATERIAL SUPPLY HEADER
PNEUMATIC CONTROL
3900 W. Hamlin Rd. Rochester Hills, Mi. 48309-3253
MATERIAL FILTER TITLE:
GM SILAO LIQUID APPLIED SOUND DEADENER ZONE CELL PLAN VIEW
ROLLING PURGE BUCKET WITH TIP BLOWOFF FLOOR MOUNTED IPS METER
LINE 1 LASD-1&2
MPS AIR VALVE R-30iB ROBOT CONTROLLER WITH TOPHAT R-30iB ROBOT CONTROLLER
MAINTENANCE AREA JUNCTION BOX
ECS-5393
R2
ISS LINE 1
ENTRANCE GATE J-BOX
MAINT. AREA J- BOX
ISS LINE 1
POWER DISTRIBUTION PANEL
ECS-5332
-
DUAL ARM 10.5M
CAMERA POWER J-BOX
SWITCHED AUX POWER
F-
-
R-30iB
M-710iC/20M
F-
FINAL ASSEMBLY RAIL LENGTH
(w/ TOPHAT)
R3
M-710iC/20M
SERIAL #
R-30iB
ISS LINE 1
R1
MODEL
ROBOT CONTROLLER
ISS LINE 1
ROBOT
ECS-5011
FANUC EQUIPMENT SERIAL NUMBERS CELL
LED POWER J-BOX
GATE ENTRY BOX
SCC
INTRUSION J- BOX W/ MUTING
COMPONENT LEGEND ENTRANCE / EXIT w/ INTRUSION RESET J-BOX
CAMERA/CAMERA HOUSING
SWITCHED AUX POWER JUNCTION BOX
L.E.D. LIGHT
REMOTE PENDANT PORT
AIR FILTER
DOOR OPEN PHOTO-EYES BODY I.D. PHOTO-EYES (STAND BY INST. CONT.) SAFETY MAT
RPP
PRELIMINARY May 16, 2016
NOTE: SYSTEM INSTALLED ON 2ND LEVEL
DRAWN BY CHECKED BY
MM. DAS
DATE: DATE:
APPRV'D. BY PROJ. NO.
10/05/15 10/__/15
DATE:
128650
SHEET NO.
4
SCALE:
TOTAL SHEETS
1/36
DRAWING NO.
DT-7183-002
NO. No.
DESCRIPTION
BY POR
DATE FECHA
NORTH
REVISIONS REVISIONES
KEY PLAN SCALE: NONE
NOTA: ESTE DIBUJO (PLANO) Y SU CONTENIDO ES PROPIEDAD DE
GENERAL MOTORS DE MEXICO, S.A. DE C.V. POR NINGUN MOTIVO DEBE SER REPODUCIDO DE FORMA ALGUNA, TAMPOCO SUMINISTRADO A ENTIDAD EXTERNA PARA SER EXAMINADO, SIN EL CONSENTIMIENTO PREVIO DE LA PROPIETARIA. ESTE DIBUJO (PLANO) SOLO DEBERA SER UTILIZADO COMO REFERENCIA O MEDIO PARA DESARROLLAR EL TRABAJO CONTRATADO. LA VIOLACION DE LO ANTES MENCIONADO PUEDE ACARREAR RESPONSABILIDAD PENAL DE ACUERDO A LO PREVISTO POR LA LEY FEDERAL DE LOS DERECHOS DE AUTOR. C
MEXICO
General Motors Corporation MEXICAN TRUCK ASSEMBLY FACILITY GM de MEXICO
120 110VAC
203FAN
CAD DATA. AVOID MANUAL CHANGES DO NOT SCALE DRAWING THE FOLLOWING ITEMS APPLY UNLESS OTHERWISE SPECIFIED: ALL GEOMETRIC DIMENSIONING AND TOLERANCING TO BE INTERPRETED PER THE AMERICAN NATIONAL STANDARD ANSI Y14.5M - 1982. FOR FEATURES OF SIZE, PERFECT STRAIGHTNESS NOT REQUIRED AT MMC. FOR DIAMETRAL FEATURES, ROUNDNESS MUST BE WITHIN THE MMC AND LMC (LEAST MATERIAL CONDITION) BOUNDARY. TRUE POSITION TOLERANCES, AND RELATED DATUMS (EXCEPT PLANE SURFACES), APPLY TO MMC. OTHER GEOMETRIC TOLERANCES AND RELATED DATUMS, APPLY RFS. SEPARATE TRUE POSITION CALLOUTS MAY BE GAGED SEPARATELY, REGARDLESS
1055
OF DATUM REFERENCE.
1055
INCH
UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS ARE IN INCHES. ALL TWO PLACE DECIMAL DIMENSIONS ±0.01 ALL THREE PLACE DECIMAL DIMENSIONS ±0.005 ALL FOUR PLACE DECIMAL DIMENSIONS ±0.0005 ALL MACHINED ANGLES ±0°-15' C'SINK ALL TAPPED HOLES. REMOVE ALL BURRS AND SHARP CORNERS. UNFINISHED CASTING AND WELDMENT DIMENSIONS ±0.12 BURNOUT DIMENSIONS ±0.12 DO NOT USE REF. DIMENSIONS FOR MANUFACTURING. DIMENSIONS IN [XX] ARE IN MILLIMETERS FOLLOW FANUC ENGINEERING STANDARDS. 125
3.2
OR BETTER ON ALL MACHINED SURFACES.
MARK PART WITH FANUC PART NO. AND REVISION LETTER THIS MATERIAL IS THE EXCLUSIVE PROPERTY OF FANUC ROBOTICS CORPORATION AND MUST BE RETURNED TO FANUC IMMEDIATELY UPON REQUEST. THIS MATERIAL AND THE INFORMATION ILLUSTRATED OR CONTAINED HEREIN MAY NOT BE REPRODUCED, COPIED, USED OR TRANSMITTED IN WHOLE OR IN PART IN ANY WAY WITHOUT THE PRIOR WRITTEN CONSENT OF FANUC.
3900 W. Hamlin Rd. Rochester Hills, Mi. 48309-3253 TITLE:
SECTION A ~ LOOKING SOUTH
PRELIMINARY May 16, 2015
GM SILAO LIQUID APPLIED SOUND DEADENER ZONE CELL END VIEW DRAWN BY CHECKED BY
MM. DAS
DATE: DATE:
APPRV'D. BY PROJ. NO.
10/05/15 10/__/15
DATE:
128650
SHEET NO.
4
SCALE:
TOTAL SHEETS
1/16
DRAWING NO.
DT-7183-002
NO. No.
DESCRIPTION
BY POR
DATE FECHA
REVISIONS REVISIONES
1
NORTH
3
1
1
3
3
3
1
KEY PLAN SCALE: NONE
NOTA: ESTE DIBUJO (PLANO) Y SU CONTENIDO ES PROPIEDAD DE
GENERAL MOTORS DE MEXICO, S.A. DE C.V. POR NINGUN MOTIVO DEBE SER REPODUCIDO DE FORMA ALGUNA, TAMPOCO SUMINISTRADO A ENTIDAD EXTERNA PARA SER EXAMINADO, SIN EL CONSENTIMIENTO PREVIO DE LA PROPIETARIA. ESTE DIBUJO (PLANO) SOLO DEBERA SER UTILIZADO COMO REFERENCIA O MEDIO PARA DESARROLLAR EL TRABAJO CONTRATADO. LA VIOLACION DE LO ANTES MENCIONADO PUEDE ACARREAR RESPONSABILIDAD PENAL DE ACUERDO A LO PREVISTO POR LA LEY FEDERAL DE LOS DERECHOS DE AUTOR. C
MEXICO
General Motors Corporation MEXICAN TRUCK ASSEMBLY FACILITY GM de MEXICO CAD DATA. AVOID MANUAL CHANGES DO NOT SCALE DRAWING THE FOLLOWING ITEMS APPLY UNLESS OTHERWISE SPECIFIED: ALL GEOMETRIC DIMENSIONING AND TOLERANCING TO BE INTERPRETED PER THE AMERICAN NATIONAL STANDARD ANSI Y14.5M - 1982. FOR FEATURES OF SIZE, PERFECT STRAIGHTNESS NOT REQUIRED AT MMC. FOR DIAMETRAL FEATURES, ROUNDNESS MUST BE WITHIN THE MMC AND LMC (LEAST MATERIAL CONDITION) BOUNDARY. TRUE POSITION TOLERANCES, AND RELATED DATUMS (EXCEPT PLANE SURFACES), APPLY TO MMC. OTHER GEOMETRIC TOLERANCES AND RELATED DATUMS, APPLY RFS. SEPARATE TRUE POSITION CALLOUTS MAY BE GAGED SEPARATELY, REGARDLESS
525
OF DATUM REFERENCE.
525
INCH
UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS ARE IN INCHES. ALL TWO PLACE DECIMAL DIMENSIONS ±0.01 ALL THREE PLACE DECIMAL DIMENSIONS ±0.005 ALL FOUR PLACE DECIMAL DIMENSIONS ±0.0005 ALL MACHINED ANGLES ±0°-15' C'SINK ALL TAPPED HOLES. REMOVE ALL BURRS AND SHARP CORNERS. UNFINISHED CASTING AND WELDMENT DIMENSIONS ±0.12 BURNOUT DIMENSIONS ±0.12 DO NOT USE REF. DIMENSIONS FOR MANUFACTURING. DIMENSIONS IN [XX] ARE IN MILLIMETERS FOLLOW FANUC ENGINEERING STANDARDS. 125
3.2
OR BETTER ON ALL MACHINED SURFACES.
MARK PART WITH FANUC PART NO. AND REVISION LETTER THIS MATERIAL IS THE EXCLUSIVE PROPERTY OF FANUC ROBOTICS CORPORATION AND MUST BE RETURNED TO FANUC IMMEDIATELY UPON REQUEST. THIS MATERIAL AND THE INFORMATION ILLUSTRATED OR CONTAINED HEREIN MAY NOT BE REPRODUCED, COPIED, USED OR TRANSMITTED IN WHOLE OR IN PART IN ANY WAY WITHOUT THE PRIOR WRITTEN CONSENT OF FANUC.
3900 W. Hamlin Rd. Rochester Hills, Mi. 48309-3253 TITLE:
SECTION B ~ LOOKING SOUTH
PRELIMINARY May 16, 2015
GM SILAO LIQUID APPLIED SOUND DEADENER ZONE CELL END VIEW DRAWN BY CHECKED BY
MM. DAS
DATE: DATE:
APPRV'D. BY PROJ. NO.
10/05/15 10/__/15
DATE:
128650
SHEET NO.
6
SCALE:
TOTAL SHEETS
1/16
DRAWING NO.
DT-7183-002
NO. No.
DESCRIPTION
BY POR
DATE FECHA
REVISIONS REVISIONES
MAXIMUM CAPACITY 600 Lbs
MAXIMUM CAPACITY 600 Lbs
3 3
1
NORTH
1
KEY PLAN SCALE: NONE
R G B A
FLOW
MAINT J-BOX
MAINT J-BOX LOK
LOK 5249HN O5242.b07 SYSTEM FAULT 5245BEA O5242.b03 ROBOTS RUNNING 5246BEA O5242.b04 SERVOS ARMED
AC
NOTA: ESTE DIBUJO (PLANO) Y SU CONTENIDO ES PROPIEDAD DE
MAINT J-BOX
SYSTEM FAULT
AC
5247BEA O5242.b05 SYSTEM BYPASSED
SUPPLY:
VOLTS
PHASE3
HZ
FULL LOAD CURRENT: DISCONNECT RATING: SHORT CIRCUIT INTERRUPT RATING:
Power Distribution Panel
CUSTOMER: PLANT: SYSTEM DESC: DRAWING NUMBER: DATE OF MANUFACTURE: EE-1505-100-117
5248BEA O5242.b06
DANGER 480VAC WARNING
PLC J-BOX
DISCONNECT POWER BEFORE WORKING WITHIN
PELTIER HEATER
PELTIER HEATER
CONTROL PANEL DWG# DE-6968-215
CONTROL PANEL DWG# DE-6968-215
SERIAL#XXXXXX
CAUTION ORANGE WIRING IS NOT DE-ENERGIZED BY MAIN DISCONNECT
SERIAL#XXXXXX
SQ "D" 9012-GAW-5 PRESSURE SWITCH
SQ "D" 9012-GAW-5 PRESSURE SWITCH
PDP
SCC 900
1025
900
GENERAL MOTORS DE MEXICO, S.A. DE C.V. POR NINGUN MOTIVO DEBE SER REPODUCIDO DE FORMA ALGUNA, TAMPOCO SUMINISTRADO A ENTIDAD EXTERNA PARA SER EXAMINADO, SIN EL CONSENTIMIENTO PREVIO DE LA PROPIETARIA. ESTE DIBUJO (PLANO) SOLO DEBERA SER UTILIZADO COMO REFERENCIA O MEDIO PARA DESARROLLAR EL TRABAJO CONTRATADO. LA VIOLACION DE LO ANTES MENCIONADO PUEDE ACARREAR RESPONSABILIDAD PENAL DE ACUERDO A LO PREVISTO POR LA LEY FEDERAL DE LOS DERECHOS DE AUTOR. C
900
MEXICO
General Motors Corporation MEXICAN TRUCK ASSEMBLY FACILITY GM de MEXICO CAD DATA. AVOID MANUAL CHANGES DO NOT SCALE DRAWING THE FOLLOWING ITEMS APPLY UNLESS OTHERWISE SPECIFIED: ALL GEOMETRIC DIMENSIONING AND TOLERANCING TO BE INTERPRETED PER THE AMERICAN NATIONAL STANDARD ANSI Y14.5M - 1982. FOR FEATURES OF SIZE, PERFECT STRAIGHTNESS NOT REQUIRED AT MMC. FOR DIAMETRAL FEATURES, ROUNDNESS MUST BE WITHIN THE MMC AND LMC (LEAST MATERIAL CONDITION) BOUNDARY. TRUE POSITION TOLERANCES, AND RELATED DATUMS (EXCEPT PLANE SURFACES), APPLY TO MMC. OTHER GEOMETRIC TOLERANCES AND RELATED DATUMS, APPLY RFS. SEPARATE TRUE POSITION CALLOUTS MAY BE GAGED SEPARATELY, REGARDLESS OF DATUM REFERENCE.
INCH
UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS ARE IN INCHES. ALL TWO PLACE DECIMAL DIMENSIONS ±0.01 ALL THREE PLACE DECIMAL DIMENSIONS ±0.005 ALL FOUR PLACE DECIMAL DIMENSIONS ±0.0005 ALL MACHINED ANGLES ±0°-15' C'SINK ALL TAPPED HOLES. REMOVE ALL BURRS AND SHARP CORNERS. UNFINISHED CASTING AND WELDMENT DIMENSIONS ±0.12 BURNOUT DIMENSIONS ±0.12 DO NOT USE REF. DIMENSIONS FOR MANUFACTURING. DIMENSIONS IN [XX] ARE IN MILLIMETERS FOLLOW FANUC ENGINEERING STANDARDS. 125
3.2
OR BETTER ON ALL MACHINED SURFACES.
MARK PART WITH FANUC PART NO. AND REVISION LETTER THIS MATERIAL IS THE EXCLUSIVE PROPERTY OF FANUC ROBOTICS CORPORATION AND MUST BE RETURNED TO FANUC IMMEDIATELY UPON REQUEST. THIS MATERIAL AND THE INFORMATION ILLUSTRATED OR CONTAINED HEREIN MAY NOT BE REPRODUCED, COPIED, USED OR TRANSMITTED IN WHOLE OR IN PART IN ANY WAY WITHOUT THE PRIOR WRITTEN CONSENT OF FANUC.
3900 W. Hamlin Rd. Rochester Hills, Mi. 48309-3253 TITLE:
SECTION C ~ LOOKING EAST
PRELIMINARY MAY 16, 2015
GM SILAO LIQUID APPLIED SOUND DEADENER ZONE CELL ELEVATION SECTION VIEW DRAWN BY CHECKED BY
MM. DAS
DATE: DATE:
APPRV'D. BY PROJ. NO.
10/05/15 10/__/15
DATE:
128650
SHEET NO.
7
SCALE:
TOTAL SHEETS
1/36
DRAWING NO.
DT-7183-002
NO. No.
DESCRIPTION
BY POR
DATE FECHA
REVISIONS REVISIONES
MAXIMUM CAPACITY 600 Lbs
MAXIMUM CAPACITY 600 Lbs
3
3 1
NORTH
1
MAINT J-BOX
FLOW
MAINT J-BOX LOK
AC
POR NINGUN MOTIVO DEBE SER REPODUCIDO DE FORMA ALGUNA, TAMPOCO SUMINISTRADO A ENTIDAD EXTERNA PARA SER EXAMINADO, SIN EL CONSENTIMIENTO PREVIO DE LA PROPIETARIA. ESTE DIBUJO (PLANO) SOLO DEBERA SER UTILIZADO COMO REFERENCIA O MEDIO PARA DESARROLLAR EL TRABAJO CONTRATADO. LA VIOLACION DE LO ANTES MENCIONADO PUEDE ACARREAR RESPONSABILIDAD PENAL DE ACUERDO A LO PREVISTO POR LA LEY FEDERAL DE LOS DERECHOS DE AUTOR. C
AC
PELTIER HEATER
PELTIER HEATER
CONTROL PANEL DWG# DE-6968-215
CONTROL PANEL DWG# DE-6968-215
SERIAL#XXXXXX
SQ "D" 9012-GAW-5 PRESSURE SWITCH
SERIAL#XXXXXX
SQ "D" 9012-GAW-5 PRESSURE SWITCH
900
1025
NOTA: ESTE DIBUJO (PLANO) Y SU CONTENIDO ES PROPIEDAD DE
GENERAL MOTORS DE MEXICO, S.A. DE C.V.
LOK
MAINT J-BOX
KEY PLAN SCALE: NONE
900
900
MEXICO
General Motors Corporation MEXICAN TRUCK ASSEMBLY FACILITY GM de MEXICO CAD DATA. AVOID MANUAL CHANGES DO NOT SCALE DRAWING THE FOLLOWING ITEMS APPLY UNLESS OTHERWISE SPECIFIED: ALL GEOMETRIC DIMENSIONING AND TOLERANCING TO BE INTERPRETED PER THE AMERICAN NATIONAL STANDARD ANSI Y14.5M - 1982. FOR FEATURES OF SIZE, PERFECT STRAIGHTNESS NOT REQUIRED AT MMC. FOR DIAMETRAL FEATURES, ROUNDNESS MUST BE WITHIN THE MMC AND LMC (LEAST MATERIAL CONDITION) BOUNDARY. TRUE POSITION TOLERANCES, AND RELATED DATUMS (EXCEPT PLANE SURFACES), APPLY TO MMC. OTHER GEOMETRIC TOLERANCES AND RELATED DATUMS, APPLY RFS. SEPARATE TRUE POSITION CALLOUTS MAY BE GAGED SEPARATELY, REGARDLESS OF DATUM REFERENCE.
INCH
UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS ARE IN INCHES. ALL TWO PLACE DECIMAL DIMENSIONS ±0.01 ALL THREE PLACE DECIMAL DIMENSIONS ±0.005 ALL FOUR PLACE DECIMAL DIMENSIONS ±0.0005 ALL MACHINED ANGLES ±0°-15' C'SINK ALL TAPPED HOLES. REMOVE ALL BURRS AND SHARP CORNERS. UNFINISHED CASTING AND WELDMENT DIMENSIONS ±0.12 BURNOUT DIMENSIONS ±0.12 DO NOT USE REF. DIMENSIONS FOR MANUFACTURING. DIMENSIONS IN [XX] ARE IN MILLIMETERS FOLLOW FANUC ENGINEERING STANDARDS. 125
3.2
OR BETTER ON ALL MACHINED SURFACES.
MARK PART WITH FANUC PART NO. AND REVISION LETTER THIS MATERIAL IS THE EXCLUSIVE PROPERTY OF FANUC ROBOTICS CORPORATION AND MUST BE RETURNED TO FANUC IMMEDIATELY UPON REQUEST. THIS MATERIAL AND THE INFORMATION ILLUSTRATED OR CONTAINED HEREIN MAY NOT BE REPRODUCED, COPIED, USED OR TRANSMITTED IN WHOLE OR IN PART IN ANY WAY WITHOUT THE PRIOR WRITTEN CONSENT OF FANUC.
3900 W. Hamlin Rd. Rochester Hills, Mi. 48309-3253 TITLE:
SECTION D ~ LOOKING WEST
PRELIMINARY MAY 16, 2015
GM SILAO LIQUID APPLIED SOUND DEADENER ZONE CELL ELEVATION SECTION VIEW DRAWN BY CHECKED BY
MM. DAS
DATE: DATE:
APPRV'D. BY PROJ. NO.
10/05/15 10/__/15
DATE:
128650
SHEET NO.
8
SCALE:
TOTAL SHEETS
1/36
DRAWING NO.
DT-7183-002
NO. No.
DESCRIPTION
BY POR
DATE FECHA
REVISIONS REVISIONES
R4
R2 ROBOT CONTROLLER
R-30iB ECS-5393
MAINT. AREA J- BOX
ECS-5393
MAINT. AREA J- BOX
ROBOT CONTROLLER
R-30iB
SCC
ECS-5393
ECS-5393
MAINT. AREA J- BOX
MAINT. AREA J- BOX
P.D.P.
ECS-5391
PLC J-BOX
NORTH
SOLA P/S
EXIT INTRUSION J- BOX W/ MUTING
R4
R2
KEY PLAN SCALE: NONE
NOTA: ESTE DIBUJO (PLANO) Y SU CONTENIDO ES PROPIEDAD DE
GENERAL MOTORS DE MEXICO, S.A. DE C.V.
M
M
CARRIER
CARRIER
"0.00"
"0.00" "0.00"
M "0.00"
M
POR NINGUN MOTIVO DEBE SER REPODUCIDO DE FORMA ALGUNA, TAMPOCO SUMINISTRADO A ENTIDAD EXTERNA PARA SER EXAMINADO, SIN EL CONSENTIMIENTO PREVIO DE LA PROPIETARIA. ESTE DIBUJO (PLANO) SOLO DEBERA SER UTILIZADO COMO REFERENCIA O MEDIO PARA DESARROLLAR EL TRABAJO CONTRATADO. LA VIOLACION DE LO ANTES MENCIONADO PUEDE ACARREAR RESPONSABILIDAD PENAL DE ACUERDO A LO PREVISTO POR LA LEY FEDERAL DE LOS DERECHOS DE AUTOR. C
MEXICO
General Motors Corporation MEXICAN TRUCK ASSEMBLY FACILITY GM de MEXICO CAD DATA. AVOID MANUAL CHANGES
R3
R1
DO NOT SCALE DRAWING THE FOLLOWING ITEMS APPLY UNLESS OTHERWISE SPECIFIED: ALL GEOMETRIC DIMENSIONING AND TOLERANCING TO BE INTERPRETED PER THE AMERICAN NATIONAL STANDARD ANSI Y14.5M - 1982. FOR FEATURES OF SIZE, PERFECT STRAIGHTNESS NOT REQUIRED AT MMC. FOR DIAMETRAL FEATURES, ROUNDNESS MUST BE WITHIN THE MMC AND LMC (LEAST MATERIAL CONDITION) BOUNDARY. TRUE POSITION TOLERANCES, AND RELATED DATUMS (EXCEPT PLANE SURFACES), APPLY TO MMC. OTHER GEOMETRIC TOLERANCES AND RELATED DATUMS, APPLY RFS. SEPARATE TRUE POSITION CALLOUTS MAY BE GAGED SEPARATELY, REGARDLESS OF DATUM REFERENCE.
MAINT. AREA J- BOX
INCH
MAINT. AREA J- BOX
MAINT. AREA J- BOX
ECS-5393
UNLESS OTHERWISE SPECIFIED
ECS-5393
ECS-5393
MAINT. AREA J- BOX ECS-5393
R-30iB
R-30iB
ROBOT CONTROLLER
ROBOT CONTROLLER
R3
ALL DIMENSIONS ARE IN INCHES. ALL TWO PLACE DECIMAL DIMENSIONS ±0.01 ALL THREE PLACE DECIMAL DIMENSIONS ±0.005 ALL FOUR PLACE DECIMAL DIMENSIONS ±0.0005 ALL MACHINED ANGLES ±0°-15' C'SINK ALL TAPPED HOLES. REMOVE ALL BURRS AND SHARP CORNERS. UNFINISHED CASTING AND WELDMENT DIMENSIONS ±0.12 BURNOUT DIMENSIONS ±0.12 DO NOT USE REF. DIMENSIONS FOR MANUFACTURING. DIMENSIONS IN [XX] ARE IN MILLIMETERS FOLLOW FANUC ENGINEERING STANDARDS.
R1
125
3.2
OR BETTER ON ALL MACHINED SURFACES.
MARK PART WITH FANUC PART NO. AND REVISION LETTER THIS MATERIAL IS THE EXCLUSIVE PROPERTY OF FANUC ROBOTICS CORPORATION AND MUST BE RETURNED TO FANUC IMMEDIATELY UPON REQUEST. THIS MATERIAL AND THE INFORMATION ILLUSTRATED OR CONTAINED HEREIN MAY NOT BE REPRODUCED, COPIED, USED OR TRANSMITTED IN WHOLE OR IN PART IN ANY WAY WITHOUT THE PRIOR WRITTEN CONSENT OF FANUC.
3900 W. Hamlin Rd. Rochester Hills, Mi. 48309-3253 TITLE:
GM SILAO LIQUID APPLIED SOUND DEADENER ZONE EQUIPMENT PLACEMENT LAYOUT - PLAN VIEW
PRELIMINARY May 16, 2016
NOTE: SYSTEM INSTALLED ON 2ND LEVEL
LINE 1 LASD-1&2
DRAWN BY CHECKED BY
MM. DAS
DATE: DATE:
APPRV'D. BY PROJ. NO.
5/13/16 5/13/16
DATE:
128650
SHEET NO.
9
SCALE:
TOTAL SHEETS
1/32
DRAWING NO.
DT-7183-002
0.00 CARRIER
"0.00" "0.00"
0.00
NO. No.
DESCRIPTION
BY POR
DATE FECHA
NORTH
REVISIONS REVISIONES
KEY PLAN SCALE: NONE
NOTA: ESTE DIBUJO (PLANO) Y SU CONTENIDO ES PROPIEDAD DE
GENERAL MOTORS DE MEXICO, S.A. DE C.V. POR NINGUN MOTIVO DEBE SER REPODUCIDO DE FORMA ALGUNA, TAMPOCO SUMINISTRADO A ENTIDAD EXTERNA PARA SER EXAMINADO, SIN EL CONSENTIMIENTO PREVIO DE LA PROPIETARIA. ESTE DIBUJO (PLANO) SOLO DEBERA SER UTILIZADO COMO REFERENCIA O MEDIO PARA DESARROLLAR EL TRABAJO CONTRATADO. LA VIOLACION DE LO ANTES MENCIONADO PUEDE ACARREAR RESPONSABILIDAD PENAL DE ACUERDO A LO PREVISTO POR LA LEY FEDERAL DE LOS DERECHOS DE AUTOR. C
MEXICO
General Motors Corporation MEXICAN TRUCK ASSEMBLY FACILITY GM de MEXICO CAD DATA. AVOID MANUAL CHANGES DO NOT SCALE DRAWING THE FOLLOWING ITEMS APPLY UNLESS OTHERWISE SPECIFIED: ALL GEOMETRIC DIMENSIONING AND TOLERANCING TO BE INTERPRETED PER THE AMERICAN NATIONAL STANDARD ANSI Y14.5M - 1982. FOR FEATURES OF SIZE, PERFECT STRAIGHTNESS NOT REQUIRED AT MMC. FOR DIAMETRAL FEATURES, ROUNDNESS MUST BE WITHIN THE MMC AND LMC
0.00
(LEAST MATERIAL CONDITION) BOUNDARY. TRUE POSITION TOLERANCES, AND RELATED DATUMS (EXCEPT PLANE SURFACES), APPLY TO MMC. OTHER GEOMETRIC TOLERANCES AND RELATED DATUMS, APPLY RFS. SEPARATE TRUE POSITION CALLOUTS MAY BE GAGED SEPARATELY, REGARDLESS OF DATUM REFERENCE.
INCH
UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS ARE IN INCHES. ALL TWO PLACE DECIMAL DIMENSIONS ±0.01 ALL THREE PLACE DECIMAL DIMENSIONS ±0.005 ALL FOUR PLACE DECIMAL DIMENSIONS ±0.0005 ALL MACHINED ANGLES ±0°-15' C'SINK ALL TAPPED HOLES. REMOVE ALL BURRS AND SHARP CORNERS. UNFINISHED CASTING AND WELDMENT DIMENSIONS ±0.12 BURNOUT DIMENSIONS ±0.12 DO NOT USE REF. DIMENSIONS FOR MANUFACTURING. DIMENSIONS IN [XX] ARE IN MILLIMETERS FOLLOW FANUC ENGINEERING STANDARDS. 125
3.2
OR BETTER ON ALL MACHINED SURFACES.
MARK PART WITH FANUC PART NO. AND REVISION LETTER THIS MATERIAL IS THE EXCLUSIVE PROPERTY OF FANUC ROBOTICS CORPORATION AND MUST BE RETURNED TO FANUC IMMEDIATELY UPON REQUEST. THIS MATERIAL AND THE INFORMATION ILLUSTRATED OR CONTAINED HEREIN MAY NOT BE REPRODUCED, COPIED, USED OR TRANSMITTED IN WHOLE OR IN PART IN ANY WAY WITHOUT THE PRIOR WRITTEN CONSENT OF FANUC.
3900 W. Hamlin Rd. Rochester Hills, Mi. 48309-3253 TITLE:
T.B.D
GM SILAO LASD ZONE CAMERA & LIGHTING PLACEMENT LAYOUT DRAWN BY CHECKED BY
MM DAS
DATE: DATE:
APPRV'D. BY PROJ. NO.
4/13/16 4/13/16
DATE:
128650
SHEET NO.
10
SCALE:
TOTAL SHEETS
1:16
DRAWING NO.
DT- 7183-002
NO. No.
DESCRIPTION
BY POR
DATE FECHA
REVISIONS REVISIONES
R3
"0.00" "0.00"
CARRIER
"0.00" "0.00"
CARRIER
R2
NORTH
R4
R1
KEY PLAN SCALE: NONE
NOTA: ESTE DIBUJO (PLANO) Y SU CONTENIDO ES PROPIEDAD DE
GENERAL MOTORS DE MEXICO, S.A. DE C.V.
REFERENCE INFO ONLY DO NOT INSTALL TO THIS PRINT
LINE 1 LASD-2
POR NINGUN MOTIVO DEBE SER REPODUCIDO DE FORMA ALGUNA, TAMPOCO SUMINISTRADO A ENTIDAD EXTERNA PARA SER EXAMINADO, SIN EL CONSENTIMIENTO PREVIO DE LA PROPIETARIA. ESTE DIBUJO (PLANO) SOLO DEBERA SER UTILIZADO COMO REFERENCIA O MEDIO PARA DESARROLLAR EL TRABAJO CONTRATADO. LA VIOLACION DE LO ANTES MENCIONADO PUEDE ACARREAR RESPONSABILIDAD PENAL DE ACUERDO A LO PREVISTO POR LA LEY FEDERAL DE LOS DERECHOS DE AUTOR. C
MEXICO
LINE 1 LASD-1
General Motors Corporation MEXICAN TRUCK ASSEMBLY FACILITY GM de MEXICO CAD DATA. AVOID MANUAL CHANGES DO NOT SCALE DRAWING THE FOLLOWING ITEMS APPLY UNLESS OTHERWISE SPECIFIED: ALL GEOMETRIC DIMENSIONING AND TOLERANCING TO BE INTERPRETED PER THE AMERICAN NATIONAL STANDARD ANSI Y14.5M - 1982. FOR FEATURES OF SIZE, PERFECT STRAIGHTNESS NOT REQUIRED AT MMC. FOR DIAMETRAL FEATURES, ROUNDNESS MUST BE WITHIN THE MMC AND LMC (LEAST MATERIAL CONDITION) BOUNDARY. TRUE POSITION TOLERANCES, AND RELATED DATUMS (EXCEPT PLANE SURFACES), APPLY TO MMC. OTHER GEOMETRIC TOLERANCES AND RELATED DATUMS, APPLY RFS. SEPARATE TRUE POSITION CALLOUTS MAY BE GAGED SEPARATELY, REGARDLESS OF DATUM REFERENCE.
INCH
UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS ARE IN INCHES. ALL TWO PLACE DECIMAL DIMENSIONS ±0.01 ALL THREE PLACE DECIMAL DIMENSIONS ±0.005 ALL FOUR PLACE DECIMAL DIMENSIONS ±0.0005 ALL MACHINED ANGLES ±0°-15' C'SINK ALL TAPPED HOLES. REMOVE ALL BURRS AND SHARP CORNERS. UNFINISHED CASTING AND WELDMENT DIMENSIONS ±0.12 BURNOUT DIMENSIONS ±0.12 DO NOT USE REF. DIMENSIONS FOR MANUFACTURING. DIMENSIONS IN [XX] ARE IN MILLIMETERS FOLLOW FANUC ENGINEERING STANDARDS. 125
3.2
OR BETTER ON ALL MACHINED SURFACES.
MARK PART WITH FANUC PART NO. AND REVISION LETTER THIS MATERIAL IS THE EXCLUSIVE PROPERTY OF FANUC ROBOTICS CORPORATION AND MUST BE RETURNED TO FANUC IMMEDIATELY UPON REQUEST. THIS MATERIAL AND THE INFORMATION ILLUSTRATED OR CONTAINED HEREIN MAY NOT BE REPRODUCED, COPIED, USED OR TRANSMITTED IN WHOLE OR IN PART IN ANY WAY WITHOUT THE PRIOR WRITTEN CONSENT OF FANUC.
3900 W. Hamlin Rd. Rochester Hills, Mi. 48309-3253 TITLE:
GM SILAO LASD ZONE VEHICLE, BODY AND CARRIER LAYOUT DRAWN BY CHECKED BY
MM DAS
DATE: DATE:
APPRV'D. BY PROJ. NO.
4/13/16 4/13/16
DATE:
128650
SHEET NO.
11
SCALE:
TOTAL SHEETS
1:48
DRAWING NO.
DT- 7183-002
