12400 Earl Jones Way Louisville, KY 40299 rev-a-shelf.com Customer Service: 800-626-1126
597 BAKEWARE ORGANIZER TOOLS REQUIRED:
#2
ESTIMATED ASSEMBLY TIME:
10 MIN CARE AND MAINTENANCE: Clean with a damp cloth and wipe parts dry.
I-597-0417
12400 Earl Jones Way Louisville, KY 40299 rev-a-shelf.com 800-626-1126
INSTRUCCIONES DE INSTALACIÓN / LES INSTRUCTIONS D’INSTALLATION
SÉPARATEUR DE PLATEAUX 597 / SEPARADOR DE BANDEJAS 597 Herramientas requeridas: Outils Requis:
#2
Tiempo estimado de ensamblado Durée de l’installation:
10 MIN Cuidado/ Entretien: Limpie con un paño húmedo y seque las partes. Lubrique los puntos de los pivotes como sea necesario. Nettoyer avec un chiffon humide et essuyer pour sécher complètement. Lubrifiez les points de pivotement si nécessaire
Rev-A-Shelf 12400 Earl Jones Way Louisville, KY 40299 www.rev-a-shelf.com
Rev-A-Shelf Rev-A-Shelf 12400 Earl Jones Way 12400 Earl Jones Way Louisville, KY 40299 Louisville, KY 40299 www.rev-a-shelf.com
Rev-A-Shelf Rev-A-Shelf 1240012400 EarlRev-A-Shelf Jones Earl Jones Way Way Rev-A-Shelf Rev-A-Shelf Rev-A-Shelf 12400 Earl40299 Jones Way Louisville, Louisville, KY KY 40299 12400 Earl Jones Way 1240012400 Earl Jones Way Earl Jones Way I-597-0417 Louisville, KY 40299 www.rev-a-shelf.com www.rev-a-shelf.com Louisville, KY 40299 40299 Louisville, KY Louisville, KY 40299 www.rev-a-shelf.com www.rev-a-shelf.com www.rev-a-shelf.com www.rev-a-shelf.com
Parts List. No. Description. Qty. A. 27 or 35 Qt.Waste Containers. 2. B. Frame. 1. C. Braces. 2. D. Basket Wires. 2. E. Handle. 1. F. #8 x 3/4” Truss Head Screws. 4.
Top left hand slide. T-449FL-0219. 14-11/16â. (372.9 mm). 21-5/8â. (549.5 mm). 12400 Earl Jones Way. Louisville, KY 40299 rev-a-shelf.com. Customer Service: ...
pre-drill pilot holes using. 7/64” bit (See Fig. 2). Adjust the mounting brackets to line up with the holes and attach to the door using (4). #6 x 1/2” flat head screws.
4) Once tray is fitted inside cabinet, use silicon adhesive around the entire perimeter and any holes you made for plumbing. Take care to seal all the cuts to ...
hinges to begin to mount your door. Measure Opening Height ______. Measure Door Height ______. Height Difference ______. Divide Difference by 2 ______.
Note 1: Be sure to measure cabinet opening and basket width to make sure basket ... but note some taller items could hit the shelf when opening and closing.
Mark screw locations to the center of the thick portion of the door at least 12-1/2” from the bottom, pre-drill pilot holes, and attach wood frame to the door with the ...
Don't worry if it is off a little. This can all be adjusted. Double stick tape will hold the door in place while you screw the brackets to cabinet door (See. Figure 7).
Figure C). Finally attach the optional handle and insert the waste container. Note: Handle should only be used if you are not using the optional Rev-a-shelf door.
assemble the trays to the cabinet door using #8 x 5/8” truss head. 7) Once the door is attached, loosen the clamp screw on the white plastic housing (approx.
36” shelf - inside cabinet width must be between 34” to 34-3/16” (864-868 mm). STEP 1. For side mounting: Mark and drill pilot holes for the base brackets to the.