The HBEM3W Extender Module allows you to attach an HB3xxW series IP65 compliant occupancy sensor to the side of a wet location light fixture. The HBEM3W ...
High Bay Occupancy Sensor Mounting Bracket Extender Module for Wet Locations No: 24121 – 09/16 rev. 1 Installation Instructions • Instructions d’Installation • Instrucciones de Instalación
Catalog Number • Numéro de Catalogue • Número de Catálogo: HBEM3W Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China
WARNING: TURN THE POWER OFF AT THE CIRCUIT BREAKER BEFORE WIRING.
The HBEM3W Extender Module allows you to attach an HB3xxW series IP65 compliant occupancy sensor to the side of a wet location light fixture. The HBEM3W includes two chase nipples; one for use with the HB340W and one for all other models. One end of the nipple snaps into the extender housing. The other end fits into a watertight fixture enclosure with a standard knockout. A rubber washer fits between the outside flange of the nipple and the outside of the fixture. The Slide blade under tabs located included nut tightens against the inside in 3 places. Gently pry apart. wall of the fixture enclosure to secure the nipple and rubber washer. The extender module snaps apart to allow threading the wiring cable through it and into the fixture for connection. The extender housing is not watertight, but the inner flange rings on the nipple and the HB3xxW housing fit into grooved rubber rings on the cable to keep moisture from entering the fixture and sensor at those locations.
INSTALLATION Assemble the HBEM3W to the HB3xxW series sensor and to the light fixture as shown in the illustrations. Note the grooved rubber ring on the sensor cable. Ensure you have selected the correct nipple for your sensor. Make sure that when the cable is threaded through the chase nipple, the slot is seated on either side of the flange ring inside the chase nipple, as shown in the explolded view. When properly seated, using moderate force you should not be able to pull the cable out of the nipple from either end.
Rubber washer
HBEM3W Extender housing
Chase nipple
Threaded nut Chase nipple
Threaded nut Inner flange ring
Grooved rubber ring
Cable Cable Threaded nut (comes with sensor) HB3xxW sensor
WARRANTY INFORMATION
INFORMATIONS RELATIVES À LA GARANTIE
INFORMACIÓN DE LA GARANTÍA
Wattstopper warranties its products to be free of defects in materials and workmanship for a period of five (5) years. There are no obligations or liabilities on the part of Wattstopper for consequential damages arising out of, or in connection with, the use or performance of this product or other indirect damages with respect to loss of property, revenue or profit, or cost of removal, installation or reinstallation.
Wattstopper garantit que ses produits sont exempts de défauts de matériaux et de fabrication pour une période de cinq (5) ans. Wattstopper ne peut être tenu responsable de tout dommage consécutif causé par ou lié à l’utilisation ou à la performance de ce produit ou tout autre dommage indirect lié à la perte de propriété, de revenus, ou de profits, ou aux coûts d’enlèvement, d’installation ou de réinstallation.
Wattstopper garantiza que sus productos están libres de defectos en materiales y mano de obra por un período de cinco (5) años. No existen obligaciones ni responsabilidades por parte de Wattstopper por daños consecuentes que se deriven o estén relacionados con el uso o el rendimiento de este producto u otros daños indirectos con respecto a la pérdida de propiedad, renta o ganancias, o al costo de extracción, instalación o reinstalación.
The sensor uses passive infrared technology to sense human motion in a ... wire from the circuit to the green ground wire on the CS-. 50. Make sure there is a ...
d'autres pièces d'équipement : • Ne pas installer un gradateur pour lampes fluorescentes pour contrôler une prise électrique, ou un appareil ménager équipé ...
warm-up time of 60 seconds before the sensor begins detecting motion. ... adjust the time delay trimpot on the sensor to change the sensitivity as follows:.
Repeat above as necessary. Note: Never adjust trim pot when circuit is live. ... always turn power off at the service panel before installing this unit, working on the ...
IMPORTANT NOTES: 1. All Fan Speed Controls can be damaged by improper wiring. Check for short circuits prior to installing the fan speed control. Procedure for short circuit check: a. Disconnect power to circuit by removing fuse or turn circuit break
All models in the HB3x0-B series use a set of DIP switches to set the time delay, .... Change the switch settings to adjust sensitivity. Time Delay (Switches 3-7).
NOTE: Make sure the sensor is pointing downward. Fixez le ... Wattstopper warranties its products to be free ... can be removed as needed to accommodate.
In the PW-203, light level only affects the load on Relay 2. ... outside of the desired area (also consider masking the lens) and where heat sources cause ... Through is active, the unit beeps three times at 10 seconds before the load goes OFF.
mounting tabs on the J-Box. 5. Snap the front cover onto the sensor. 4" Square, 2.25" Deep*. Junction Box with. Double Gang. Mudring attached. Drop Ceiling.
The HB350* can be attached either directly to the fixture surface via the two screw holes .... connection with, the use or performance of this product or other ...
PIR Fixture Integrated Outdoor Sensor In IP66 Enclosure ..... Check light level parameter, to find out the amount of light that the sensor is detecting. Cover the ...
All dimmers can be damaged by improper wiring. Check for short circuits prior to installing the dimmer with a lamp load in the circuit. Procedure for short circuit ...
Installation Instructions • Instructions d'Installation • Instrucciones de Instalación. No: 23948 – 04/19 rev. 6. Catalog Number • Numéro de Catalogue • Número de ...
NOTE: After 10 minutes, the PW-311 will exit Setup Mode even if the four DIP switches .... 8. Time. Delay. Mode. ON. Additional. Features. Unused. Test/3 min.
Passive Infrared Wall Switch Occupancy Sensor (version 3) ... A “walk-through” mode can turn lights off after only 3 minutes, if no activity is detected after 30.
Si el dispositivo todavía no está instalado en la caja de pared, proceda al Paso 1 de la sección Procedimiento de Cambio de Color. 2. Si el dispositivo está ...
All dimmers can be damaged by improper wiring. Check for short ... Any dimmer damage due to improper installation is not covered under warranty. COLOR ...
If using a CX sensor, remove the mounting post bracket by rotating clockwise. 2. Attach sensor to the ... Wattstopper warranties its products to be free of defects in ...
