HBP Sensor Surface Mount Module Module de montage en surface du capteur HBP Módulo de montaje en superficie del sensor HBP Installation Instructions • Instructions d’Installation • Instrucciones de Instalación
Catalog Number • Numéro de Catalogue • Número de Catálogo: HBP-SM1 Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China
UL Listed Fixture Élément certifié UL Prestación calificada por UL
Minimum Ø0.85” (21.60) mm free of burrs or sharp edges Diamètre minimum de 21,60 mm (0,85 po sans bavure ou arête tranchante) Diámetro mínimo 0,85 pulg. (21,60 mm) sin rebabas ni bordes filosos HBP-SM1 Distance from center to mounting hole: 2.36” (59.9mm) Distance du centre de trou de montage: 59,9 mm (2,36 po) Distancia del centro al orificio de montaje: 59,9 mm (2,36 pulg)
WARRANTY INFORMATION
INFORMATIONS RELATIVES À LA GARANTIE
INFORMACIÓN DE LA GARANTÍA
Wattstopper warranties its products to be free of defects in materials and workmanship for a period of five (5) years. There are no obligations or liabilities on the part of Wattstopper for consequential damages arising out of, or in connection with, the use or performance of this product or other indirect damages with respect to loss of property, revenue or profit, or cost of removal, installation or reinstallation.
Wattstopper garantit que ses produits sont exempts de défauts de matériaux et de fabrication pour une période de cinq (5) ans. Wattstopper ne peut être tenu responsable de tout dommage consécutif causé par ou lié à l’utilisation ou à la performance de ce produit ou tout autre dommage indirect lié à la perte de propriété, de revenus, ou de profits, ou aux coûts d’enlèvement, d’installation ou de réinstallation.
Wattstopper garantiza que sus productos están libres de defectos en materiales y mano de obra por un período de cinco (5) años. No existen obligaciones ni responsabilidades por parte de Wattstopper por daños consecuentes que se deriven o estén relacionados con el uso o el rendimiento de este producto u otros daños indirectos con respecto a la pérdida de propiedad, renta o ganancias, o al costo de extracción, instalación o reinstalación.
d'autres pièces d'équipement : • Ne pas installer un gradateur pour lampes fluorescentes pour contrôler une prise électrique, ou un appareil ménager équipé ...
warm-up time of 60 seconds before the sensor begins detecting motion. ... adjust the time delay trimpot on the sensor to change the sensitivity as follows:.
Repeat above as necessary. Note: Never adjust trim pot when circuit is live. ... always turn power off at the service panel before installing this unit, working on the ...
IMPORTANT NOTES: 1. All Fan Speed Controls can be damaged by improper wiring. Check for short circuits prior to installing the fan speed control. Procedure for short circuit check: a. Disconnect power to circuit by removing fuse or turn circuit break
All models in the HB3x0-B series use a set of DIP switches to set the time delay, .... Change the switch settings to adjust sensitivity. Time Delay (Switches 3-7).
NOTE: Make sure the sensor is pointing downward. Fixez le ... Wattstopper warranties its products to be free ... can be removed as needed to accommodate.
In the PW-203, light level only affects the load on Relay 2. ... outside of the desired area (also consider masking the lens) and where heat sources cause ... Through is active, the unit beeps three times at 10 seconds before the load goes OFF.
The HB350* can be attached either directly to the fixture surface via the two screw holes .... connection with, the use or performance of this product or other ...
PIR Fixture Integrated Outdoor Sensor In IP66 Enclosure ..... Check light level parameter, to find out the amount of light that the sensor is detecting. Cover the ...
All dimmers can be damaged by improper wiring. Check for short circuits prior to installing the dimmer with a lamp load in the circuit. Procedure for short circuit ...
Installation Instructions • Instructions d'Installation • Instrucciones de Instalación. No: 23948 – 04/19 rev. 6. Catalog Number • Numéro de Catalogue • Número de ...
NOTE: After 10 minutes, the PW-311 will exit Setup Mode even if the four DIP switches .... 8. Time. Delay. Mode. ON. Additional. Features. Unused. Test/3 min.
Passive Infrared Wall Switch Occupancy Sensor (version 3) ... A “walk-through” mode can turn lights off after only 3 minutes, if no activity is detected after 30.
The HBEM3W Extender Module allows you to attach an HB3xxW series IP65 compliant occupancy sensor to the side of a wet location light fixture. The HBEM3W ...
The sensor uses passive infrared technology to sense human motion in a ... wire from the circuit to the green ground wire on the CS-. 50. Make sure there is a ...
mounting tabs on the J-Box. 5. Snap the front cover onto the sensor. 4" Square, 2.25" Deep*. Junction Box with. Double Gang. Mudring attached. Drop Ceiling.
Alojamiento en Posada***. DÍA 3: Etapa .... DÍA 2: Etapa Ponferrada – Villafranca del Bierzo - 21 Km. DÍA 3: Etapa Villafranca del Bierzo - Cebreiro 29 Km.
Si el dispositivo todavía no está instalado en la caja de pared, proceda al Paso 1 de la sección Procedimiento de Cambio de Color. 2. Si el dispositivo está ...
All dimmers can be damaged by improper wiring. Check for short ... Any dimmer damage due to improper installation is not covered under warranty. COLOR ...
If using a CX sensor, remove the mounting post bracket by rotating clockwise. 2. Attach sensor to the ... Wattstopper warranties its products to be free of defects in ...
EMI/RFI — Interférence électromagnétique et aux fréquences radio- électriques. Capacité de la prise à atténuer le bruit électrique transmis. Configuration prise ...