V.I.A.™ - Ambient Direct LED Light Fixture
®
120/277V AC WHITE BLACK
0-10V Dimming
24V DC BLUE RED
VIOLET GRAY
Neutral WHT
DRIVERS WILL NOT DIM TO OFF, THEY MUST BE SWITCHED DIMMING RANGE OUTPUT 100% - 10% IF DIMMING NOT USED, CAP VIOLET AND GRAY LEADS LIMIT NUMBER OF DRIVERS WIRED TO ONE DIMMER SWITCH = 1-6 AS SHOWN LIMIT NUMBER OF LINEAR FEET OF VIA WIRED TO ONE DRIVER TO 120"
BLK
Line
+
LED DRVR
LED DRVR
DIMMER SWITCH
LED DRVR
LED DRVR
LED DRVR
LED DRVR
-
BLUE
RED GRAY
+ VIA PANEL(S)
+ VIA PANEL(S)
VIOLET
120" Max
120" Max
+ VIA PANEL(S)
120" Max
+ VIA PANEL(S)
120" Max
+ VIA PANEL(S)
120" Max
+ VIA PANEL(S)
120" Max
NOTE: Power supply, dimmer switch, electrical enclosure (J-box), associated 16 AWG wiring, and switching to be installed by a licensed electrical contractor in accordance with local codes.
BLANCO NEGRO
120/277V AC
AZUL ROJO
24V DC
VIOLETA GRIS
0-10V Reducción
Neutral BLANCO
Línea
NEGRO
ROJO GRIS VIOLETA
(Outside the U.S.A., Canada, Mexico, Puerto Rico, and the U.S. Virgin Islands, call: 1.616.247.2500) Or visit our website: www.steelcase.com © 2017 Steelcase Inc.
Grand Rapids, MI 49501 U.S.A. Printed in U.S.A.
SMALL PRY BAR WITH ELECTRICAL TAPE (FOR REMOVAL PROCESS ONLY)
LED DRVR
LED DRVR
REGULADOR DE INTENSIDAD + -
If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE (888.783.3522) for immediate action by people who want to help you.
LOS CONDUCTORES NO SE APAGARÁN, DEBEN ESTAR ENCENDIDOS SALIDA DE LA GAMA DE ATENUACIÓN 100% - 10% SI NO SE UTILIZA LA INCLINACIÓN, CAP VIOLETA Y GREY LEADS NÚMERO DE LÍMITES DE CONDUCTORES CONECTADOS CON CABLE A UN CONMUTADOR DE DIMMER = 1-6 COMO SE MUESTRA LÍMITE NÚMERO DE PIES LINEALES DE VIA CON CABLE A UN CONDUCTOR A 120 PULGADAS
LED DRVR
LED DRVR
LED DRVR
LED DRVR
AZUL + VIA PANEL(S)
120 pulgadas máximas
+ VIA PANEL(S)
120 pulgadas máximas
+ VIA PANEL(S)
120 pulgadas máximas
+ VIA PANEL(S)
120 pulgadas máximas
+ VIA PANEL(S)
120 pulgadas máximas
+ VIA PANEL(S)
120 pulgadas máximas
NOTA: La alimentación, interruptor de atenuación, la caja eléctrica (caja J), el cableado 16 AWG asociado e interruptores deben ser instalados por un contratista eléctrico autorizado según las normas locales.
Page 1 of 12 939502341 Rev F
®
REQUIREMENTS: 1) Wiring run from the power supply to the LED light fixture (supplied and installed by a licensed electrical contractor in accordance with local codes) shall be 16 AWG jacketed wire. 2) Each light fixture has its own individual wiring run and is not to exceed 30 feet. NOTE: Exceeding maximum wiring run will result in voltage drop and reduced preformance of the light. 3) One power supply can drive multiple light fixtures, up to, but not to exceed, 120 linear inches total, of LED light fixtures, in any combination of lengths.
REQUISITOS: 1) El recorrido del cableado desde la fuente de alimentación hasta la lámpara LED (provisto e instalado por un contratista eléctrico autorizado según las normas locales) debe ser con alambre 16 AWG con envoltura. 2) Cada lámpara tiene su propio recorrido de cable y no debe exceder los 30 pies. NOTA: Si el cableado excede el máximo recorrido se producirá una caída de voltaje y se reducirá el rendimiento de la lámpara. 3) Una fuente de alimentación puede hacer funcionar varias lámparas, hasta, pero sin exceder un total de 120 pulgadas lineales, de lámparas LED, haciendo cualquier combinación de longitudes.
Page 2 of 12 939502341 Rev F
®
1. Dependent on the length, position and snap mounting clips at both ends of the fixture at the following locations: • 12 inches for fixtures 48 inches and longer. • 5 inches for fixtures less than 48 inches. NOTE: If light fixture is 72 inches or longer, you will need a third upper and lower mounting clip that will need to be mounted in the middle of the light fixture. 12 INCHES (UNITS 48 INCHES AND LONGER)
UPPER MOUNTING CLIPS
12 INCHES (UNITS 48 INCHES AND LONGER)
5 INCHES (UNITS LESS THAN 48 INCHES)
5 INCHES (UNITS LESS THAN 48 INCHES)
LOWER MOUNTING CLIPS
BACK VIEW OF LIGHT FIXTURE
SIDE VIEW OF LIGHT FIXTURE Page 3 of 12 939502341 Rev F
®
2. Strip 1/2 inch insulation off both wires on light fixure. Strip 1/2 inch insulation off both wires from the power source. Connect these low voltage leads (typically red-to-red / black-to-black) using the appropriate size wire nut connectors.
NOTE: Route any electrical harnesses that need to pass through this area prior to installing any single Ambient Direct LED Light Fixture. Back to back fixtures restrict the routing of electrical harnesses.
Page 4 of 12 939502341 Rev F
®
3. Tip the upper edge of the light fixture into the frame opening and engage the leaf spring tab of the upper mounting clips into the trough area of the intermediate horizontal beam. 4. While lifting upward, rotate the bottom edge into the opening. Apply pressure to the bottom edge of the light fixture in the approximate location of the lower mounting clips to fully engage the frame.
3
NOTE: Consistent horizontal reveals (top and bottom edges) and flush with surrounding wall surface elements confirm proper engagement to the frame.
5. Lightly move the light fixture left or right to adjust vertical reveals for alignment with the other wall surface elements.
4
NOTE: The following are approved cleaning products for use on this light fixture. Tap water All purpose Mr. Clean All purpose Fantastik Multi-purpose Glass Plus Windex Window Cleaner Formula 409
SIDE VIEW
SIDE VIEW
Page 5 of 12 939502341 Rev F
®
Removal Process TIP: To prevent marring and surface damage, wrap the pry bar or other leverage tool with electrical tape and/or use a protective surface (such as a putty knife) before lifting against other surface elements.
1. Using a small pry bar, start at one end of the light fixture at the approximate location of lower mounting clip.
3
2. Carefully lift the light fixture approximately 1/8 inch upward and rotate out at the bottom edge. 3. Repeat at the middle clip location if the light fixture is 72 inches or greater, and again at the opposite end.
1
NOTE: Once rotated sufficiently out of the frame opening, the fixture should drop down and disengage the upper mounting clips.
4. Remove one (1) wire nut connector and
2
separate the leads. Replace the wire nut on the 16 AWG power lead.
5. Repeat with the other wire nut connector/power lead.
PRY BAR
SIDE VIEW Page 6 of 12 939502341 Rev F
®
TYPICAL APPLICATION WIRING DIAGRAMS:
CONDITIONS OF ACCEPTABILITY - LED electrical components
C
The chassis of each LED Driver (Power Supply) must be connected to earth ground in the end use application.
Master Lighting Controller (Crestron, other)
LED Driver (Power Supply) is intended for installation inside an electrical enclosure (see pages 8-11).
- -
Building Power White (Neutral)
LED Dimming Control circuit is 0-10V DC and must be used with either 100K Logarithmic or 100K Audio Tape2 potentiometer, or a standard 0-10V DC dimmer switch.
V.I.A. LED Fixture 12" min. - 120" max.
+ +
Black (Line)
Class2 LED 24 VDC Driver 120 V-277 VAC 4.0A Max Output Input
Red (+)
Red (+) V.I.A. LED Fixture 12" min. - 120" max.
Blue (-)
Black (-) V.I.A. LED Fixture 12" min. - 120" max.
Gray (-)
Violet (+)
CONDICIONES DE ACEPTABILIDAD - componentes eléctricos LED
Note: Multi tures NTE 120"total combined length per driver
Master Lighting Controller (Crestron or Similar)
El chasis de cada excitador LED (fuente de alimentación) debe conectarse a tierra en la aplicación final. El chasis de cada excitador LED (fuente de alimentación) está destinado a la instalación dentro de un recinto eléctrico (vea las páginas 8-11).
D
120V-277 VAC Compatible Toggle On/Off 3-Way Switching
El circuito del control de atenuación del LED es de 0-10 voltios DC y debe usarse sea con un potenciómetro de 100K Logarítmica o 100K Audio Tape2 o con un interruptor atenuador estándar de 0-10V DC.
V.I.A. LED Fixture 12" min. - 120" max.
Black
A
Black (Line)
120V-277 VAC Compatible Toggle On/Off Switch Building Power Violet (+)
Black (Line) Building Power
White White (Neutral)
Red (+)
Black Class 2 LED Driver 120 V-277 VAC Input
24 VDC 4.0A Max Output
White (Neutral)
V.I.A. LED Fixture 12" min. - 120" max.
Gray (-)
Class 2 LED Driver 120 V-277 VAC Input
Red (+) 24 VDC 4.0A Max Output
V.I.A. LED Fixture 12" min. - 120" max. Blue (-)
Black (-) V.I.A. LED Fixture 12" min. - 120" max.
Violet (+)
Red (+) V.I.A. LED Fixture 12" min. - 120" max.
Blue (-)
Red (+)
Gray (-)
Note: Multiple fixtures NTE 120" total combined length per driver
Black (-) V.I.A. LED Fixture 12" min. - 120" max.
E
120V-277 VAC Compatible 1-Toggle On/Off, 1-Dimmer Type 3-Way Switching
Note: Multiple fixtures NTE 120" total combined length per driver
B
3-Way Compatible Dimming Switch
0-10V Compatible Dimmer Switch (Rotary, slide, preset, etc.) Black (Line)
White (Neutral)
V.I.A. LED Fixture 12" min. - 120" max.
Black Black (Line)
0-10 V Compatible Dimming Switch
Violet (+)
Building Power
3-Way On/Off Toggle Switch
Cl ass2 LED Driver 120V-277VAC Input
V.I.A. LED Fixture 12" min. - 120" max.
Gray (-)
24 VDC 4.0A Max Output
Red (+)
Red (+)
Blue (-)
Black (-)
Building Power White (Neutral)
Class 2 LED Driver 120 V-277 VAC Input
Violet (+)
Note: Multi tures NTE 120"total combined length per driver
24 VDC 4.0A Max Output
Red (+) V.I.A. LED Fixture 12" min. - 120" max.
Blue (-)
Black (-) V.I.A. LED Fixture 12" min. - 120" max.
V.I.A. LED Fixture 12" min. - 120" max.
V.I.A. LED Fixture 12" min. - 120" max.
Red (+)
Gray (-)
Note: Multiple fixtures NTE 120" total combined length per driver
Page 7 of 12 939502341 Rev F
®
MINIMUM SPACING REQUIREMENTS FOR LAYOUT OF ELECTRICAL COMPONENTS WITHIN RECOMMENDED ELECTRICAL ENCLOSURES. REQUISITOS MÍNIMOS DE SEPARACIÓN PARA LA DISPOSICIÓN DE LOS COMPONENTES ELÉCTRICOS DENTRO DE LAS CAJAS ELÉCTRICAS RECOMENDADAS. ONE (1) DIMMING POWER SUPPLY UNA (1) REDUCCIÓN DE LA FUENTE DE ALIMENTACIÓN 254 10.00
305 12.00
2.00 MIN
1.00 MIN
1.00 MIN
305 12.00 2.00 MIN
POWER SUPPLY
305 12.00
POWER SUPPLY
1.00 MIN
1.00 MIN
LAYOUT - ENCLOSURE, 12 X 10 X 4 DISPOSICIÓN - CAJA 12 X 10 X 4
LAYOUT - ENCLOSURE, 12 X 12 X 4 DISPOSICIÓN - CAJA 12 X 12 X 4
ENCLOSURE RECOMMENDATION RECOMENDACIÓN DE LA CAJA HUBBEL-WIEGMANN Part Number SC101204
ENCLOSURE RECOMMENDATION RECOMENDACIÓN DE LA CAJA HUBBEL-WIEGMANN Part Number SC121204
Page 8 of 12 939502341 Rev F
®
MINIMUM SPACING REQUIREMENTS FOR LAYOUT OF ELECTRICAL COMPONENTS WITHIN RECOMMENDED ELECTRICAL ENCLOSURES. REQUISITOS MÍNIMOS DE SEPARACIÓN PARA LA DISPOSICIÓN DE LOS COMPONENTES ELÉCTRICOS DENTRO DE LAS CAJAS ELÉCTRICAS RECOMENDADAS. 304.809 12.00
TWO (2) DIMMING POWER SUPPLIES DOS (2) REDUCCIÓN DE LA FUENTE DE ALIMENTACIÓN
1.00 MIN
381.009 15.00
4.00 MIN
1.00 MIN
LAYOUT - ENCLOSURE, 24 X 12 X 4 DISPOSICIÓN - CAJA 24 X 12 X 4 ENCLOSURE RECOMMENDATION RECOMENDACIÓN DE LA CAJA HUBBEL-WIEGMANN Part Number SC122404
2.00 MIN
1.00 MIN
2.00 MIN
POWER SUPPLY
POWER SUPPLY
2.00 MIN
2.00 MIN
457.209 18.00
POWER SUPPLY
381.009 15.00
609.618 24.00
POWER SUPPLY
2.00 MIN
POWER SUPPLY
1.00 MIN
POWER SUPPLY
381.009 15.00
4.00 MIN
2.00 MIN
1.00 MIN
LAYOUT - ENCLOSURE, 15 X 15 X 4 DISPOSICIÓN - CAJA 15 X 15 X 4
LAYOUT - ENCLOSURE, 18 X 15 X 4 DISPOSICIÓN - CAJA 18 X 15 X 4
ENCLOSURE RECOMMENDATION RECOMENDACIÓN DE LA CAJA HUBBEL-WIEGMANN Part Number SC151504
ENCLOSURE RECOMMENDATION RECOMENDACIÓN DE LA CAJA HUBBEL-WIEGMANN Part Number SC151804
Page 9 of 12 939502341 Rev F
®
MINIMUM SPACING REQUIREMENTS FOR LAYOUT OF ELECTRICAL COMPONENTS WITHIN RECOMMENDED ELECTRICAL ENCLOSURES. REQUISITOS MÍNIMOS DE SEPARACIÓN PARA LA DISPOSICIÓN DE LOS COMPONENTES ELÉCTRICOS DENTRO DE LAS CAJAS ELÉCTRICAS RECOMENDADAS. FOUR (4) DIMMING POWER SUPPLIES CUATRO (4) REDUCCIÓN DE LA FUENTE DE ALIMENTACIÓN
THREE (3) DIMMING POWER SUPPLIES TRES (3) REDUCCIÓN DE LA FUENTE DE ALIMENTACIÓN 610 24.00
762 30.00
457 18.00
4.00 MIN
1.00 MIN 4.00 MIN
POWER SUPPLY
POWER SUPPLY
2.00 MIN
POWER SUPPLY
2.00 MIN
POWER SUPPLY
POWER SUPPLY
POWER SUPPLY
POWER SUPPLY
2.00 MIN
457 18.00
4.00 MIN
4.00 MIN
2.00 MIN
1.00 MIN
4.00 MIN
LAYOUT - ENCLOSURE, 24 X 18 X 4 DISPOSICIÓN - CAJA 24 X 18 X 4
LAYOUT - ENCLOSURE, 30 X 18 X 4 DISPOSICIÓN - CAJA 30 X 18 X 4
ENCLOSURE RECOMMENDATION RECOMENDACIÓN DE LA CAJA HUBBEL-WIEGMANN Part Number SC182404
ENCLOSURE RECOMMENDATION RECOMENDACIÓN DE LA CAJA HUBBEL-WIEGMANN Part Number SC183004
Page 10 of 12 939502341 Rev F
®
MINIMUM SPACING REQUIREMENTS FOR LAYOUT OF ELECTRICAL COMPONENTS WITHIN RECOMMENDED ELECTRICAL ENCLOSURES. REQUISITOS MÍNIMOS DE SEPARACIÓN PARA LA DISPOSICIÓN DE LOS COMPONENTES ELÉCTRICOS DENTRO DE LAS CAJAS ELÉCTRICAS RECOMENDADAS. FIVE (5) DIMMING POWER SUPPLIES CINCO (5) REDUCCIÓN DE LA FUENTE DE ALIMENTACIÓN
SIX (6) DIMMING POWER SUPPLIES SEIS (6) REDUCCIÓN DE LA FUENTE DE ALIMENTACIÓN
610 24.00
762 30.00
1.00 MIN
610 24.00
POWER SUPPLY
POWER SUPPLY
POWER SUPPLY
1.00 MIN
POWER SUPPLY
1.00 MIN
1.00 MIN
1.00 MIN
4.00 MIN
1.00 MIN 4.00 MIN
POWER SUPPLY
POWER SUPPLY
POWER SUPPLY
2.00 MIN
POWER SUPPLY
POWER SUPPLY
POWER SUPPLY
2.00 MIN
POWER SUPPLY
610 24.00
4.00 MIN
4.00 MIN 4.00 MIN
LAYOUT - ENCLOSURE, 24 X 24 X 4 DISPOSICIÓN - CAJA 24 X 24 X 4
LAYOUT - ENCLOSURE, 30 X 24 X 6 DISPOSICIÓN - CAJA 30 X 24 X 6
ENCLOSURE RECOMMENDATION RECOMENDACIÓN DE LA CAJA HUBBEL-WIEGMANN Part Number SC242404
ENCLOSURE RECOMMENDATION RECOMENDACIÓN DE LA CAJA HUBBEL-WIEGMANN Part Number SC243006
Page 11 of 12 939502341 Rev F
®
TROUBLE-SHOOTING GUIDE
PROBLEM
POTENTIAL CAUSE
TROUBLE-SHOOT
REMEDY
Fixture will not turn on.
No incoming power to driver.
Check for power at driver input connection.
Ensure power to driver.
Maximum total length limit per driver is exceeded.
Measure linear feet of fixture(s) connected to driver (120” max total length limit per driver).
Add driver(s) and/or adjust connections to balance the requirements placed on each driver to 120” maximum limit.
Driver failed.
Check driver using a simple low voltage (5-50 Vac/Dc) tester. Confirm fixture works using a different driver.
Replace driver.
Dimming failed.
Confirm fixture works using a different driver. Confirm Dimmer is functioning and compatible 0-10V type.
Replace driver or dimmer.
LED strip failed.
Confirm the driver function using a simple low voltage (5-50 Vac/Dc) tester, or try using a known working driver.
Replace fixture.
Circuit failed on LED strip.
Confirm the driver function using a simple low voltage (5-50 Vac/Dc) tester, or try using a known working driver.
Replace fixture.
Not all LED's are lit.
Page 12 of 12 939502341 Rev F
