Not included. Use LPS or SELV output CONNECT-BDG2-2 5 V- 550–1000 mA USB Micro Included (5 V- 300 mA) Connector T-5V-PS-KIT-BL (included): CONNECT-BDG2-3 Input: 100 – 240 V~ 50/60 Hz 300 mA; Included (5 V- 300 mA) Output: 5 V- 1000 mA
Status LED Bar Blink Codes
1. Using the Ethernet cable, connect the Lutron Connect Bridge to a wireless router on the same network (subnet) as the RadioRA 2 main repeater or the HomeWorks QS processor. 2. Attach the DC power adapter cord to the power jack on the Lutron Connect Bridge and insert the DC power adapter plug into a receptacle. 3. Use the RadioRA 2 or HomeWorks QS design software to activate the Lutron Connect Bridge into the system. Ensure convenient access to the “Add” button because it will be used for activating the Bridge into the system and pairing with the Lutron Connect App. 4. Use the Lutron Connect App to control and monitor the system through the Lutron Connect Bridge. The “Add” button will be used for pairing the app to the Bridge. RadioRA 2 Main Repeater
Typical Power Consumption*: 1.3 W
DC Power Adapter
Please Read Before Installing
Lutron Connect App
Lutron Connect Bridge
Use these instructions to install the model numbers listed above. 2.75 (69.9)
For more information visit: www.lutron.com/radiora2 or www.lutron.com/hwqs To obtain the required app, search for “Lutron Connect” in the app marketplace for your smart device.
Ethernet Connection
RadioRA 2 Main Repeater
Front View Status LED Bar
USB
Repeater Status 1
M
2
3
4
Communication RF
Setup
Wired
Test
Wireless Router (not sold by Lutron)
Add
1.19 (30.2) Power Repeater Link COM
N/C
MUX
MUX
9V
1
2
3
4
Integrate RS232
Ethernet Connection
Program / Integrate Ethernet
* Typical Power Consumption test conditions: LED on, Ethernet cable plugged in, powered by the 5 V- adapter. Lutron Electronics Co., Inc. 7200 Suter Road Coopersburg, PA 18036-1299
HomeWorks QS Processor 2.75 (69.9)
DC Power Adapter
Lutron Connect Bridge
Lutron Connect App
Connections Back View “Add” Button Power Jack (to adapter) NEC® Class 2, LPS or SELV, limited energy (
PRECAUCIÓN: Utilizar únicamente con luminarias de instalación fija y con los siguientes focos roscados y atenuables: lámpara fluorescentes compactas autobalastradas, LED y halógenos o incandescentes o LutronR drivers Hi-lumeR LED Serie A. Para evitar
Snap on slider and faceplate. 8. Turn power ON at circuit .... Black. White. Dimming Ballast. Dimming Ballast. Wiring Diagram 1. Line/Hot. Black. Control. Ground.
attachment screws or 2) the circuit is protected by a ground fault circuit interrupter (GFCI). When installing a control according to these methods, cap or remove green wire before screwing control into wallbox. 5. For new installations, install a te
If moisture or condensation is evident, allow the product to dry completely before installation. ... Set photo cell: Turn the blue knob full clockwise (lights.
clockwise to make the setting slightly above minimum (just .... This warranty does not cover the cost of installation, removal or reinstallation, or damage resulting.Falta(n):
Precaución: En instalación de atenuador Halógeno/Incandescente - Para reducir el riesgo de recalentamiento y posibles daños a otros equipos NO UTILICE ...
For -CDT and -CUS models, do not place sensor within 6 ft (1.2 m) of air vents, .... Photo cell has no effect on operation ... Relay Model Option: -R models only.
4 oct. 2012 - Large: 30W models. Remove protective film on the impact guard lens. Insert the lens into the corresponding slots of the visor by flexing the visor.
to the lamp or fan (LOAD) to the red wire on the ... NEUTRAL. Red ->LOAD (power to lamp or fan) ... and workmanship for a period of five (5) years. There are no ...
SHIP TO: 3649 Cane Run Road • Louisville, KY 40211-1961. (502) 778-2731 • 1 (800) 928-PUMP • FAX (502) 774-3624 visit our web site: www.zoeller.com. ®. Your Peace of Mind is Our Top Priority® .... Product on our website: .... Gate valve, shut-off val
power off at the service panel and lock the service ...... ou scie alternative. Cisailles à étain ...... NOTE: While performing installations described in this book,.
r To assure proper positioning in relation to wall, note roughing-in dimensions. Product names listed herein are trademarks of AS America, Inc. ? AS America ...
your appliance, follow basic precautions, including the following: â¡ Read all .... If the problem persists, call GE Appliances at 800. GE.CARES ...... WiFi Connect (For customers in the United States only - on some models). Depending on the ...
Keep flammable materials and vapors, such as gasoline, away from refrigerator. Failure to ...... When pushing the refrigerator back, make sure you don't roll over ...
period, before using a washing machine, turn on all hot-water faucets and let the ... GE Appliances strongly recommends the use of new water supply hoses.
If the refrigerator is operated before the water connection is made to the ice maker, ..... plumber to correct water hammer before installing the water supply line to ...
piping system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than ...
the air back into the room, proceed to page 6. Below are examples of ... For satisfactory air movement, the total duct length of. 31»4 ..... Lift microwave, tilt it forward and unhook slots at ..... Un electricista calificado deberá realizar un contr
If the above checklist does not uncover the problem, consult the factory. Do not attempt to service or otherwise disassemble pump. Service must be performed by Zoeller Authorized Service Stations. Go to www.zoellerpumps.com/servicestations to find th
If the installation does not have such a receptacle, it must be changed to the proper type, wired ... marine areas. 11. ..... As tether length increases, so does the.
applicable codes and standards, including fire.rated construction. ... published by the National Fire Protection. Association (NFPA) .... use the High. Ceiling Duct.
Before the washer is removed from service or discarded, remove the door or lid. Failure to ...... Scan this code .... adequate clearance for installation and service.
