Fujitsu LifeBook N3510 Metal Motherboard Cover Replacement
Escrito por: Neil Daniels. Fujitsu LifeBook N3510 ... Use a spudger to lift the back of the hinge cover on the left and right sides of the computer.. Paso 4. Lay the ...
Fujitsu LifeBook N3510 Metal Motherboard Cover Replacement
Paso 11 — Metal Motherboard Cover
Remove the following screws, all labeled "3."
Two 8.63mm screws.
One 7.65mm screw.
One 5.74mm screw.
Remove the following screw, labeled "15."
One 17.81mm screw.
Paso 12
Lift the cover with fingers and remove.
To reassemble your device, follow these instructions in reverse order. La versión más reciente de este documento fue generada en 2017-10-16 08:53:09 AM .
Use sus dedos para empujar los clips hacia adentro y luego hacia arriba.. Levante la batería del ordenador.. Fujitsu LifeBook N3510 reemplazo del teclado.
Press and hold the battery release button and slide the battery away from the Nokia logo.. Paso 2 â SIM card. Slide the SIM card lock away from the SIM card.
Remove three 5.5 mm T5 Torx screws from the back of the phone. ... After separating the sides, make sure there is a noticeable gap between the back case and ...
be plastic opening tools, PH #000 screwdriver and tweezers. With these prepared everything should be ready to start the replacement of the motherboard for the ...
This efficient guide will assist in opening the external casing of the Polaroid A10 by removing the back panel to access the internal device. Escrito por: Shilpa ...
remove it.. A small spoon can be used in place of a spudger.. Lever the expansion pack out using a metal spudger.. Nintendo 64 Metal Plate Replacement.
Sceptre X9 Komodo VII Video Motherboard. Replacement. This guide will remove and install the video motherboard. Escrito por: David Taylor. Sceptre X9 ...
Remove the five "F2" screws with a. Phillips #0 screwdriver.. Paso 4. Insert the plastic opening tool above the F1 key.. Apply upward pressure until the black ...
La versión más reciente de este documento fue generada en 2017-12-08 05:02:20 PM . Paso 1 â Cover. Grip the cover firmly with your thumb and index finger.
Phillips #00 Screwdriver (1). iFixit Opening Tools (1). T5 Torx Screwdriver (1) ... Use the plastic opening tool to pry off the front panel.. Palm Zire 71 Back Cover ...
28 sept. 2016 - Oculus Rift DK1 Control Box Bottom Cover. Replacement. Readers will be able to take apart the Oculus Rift control box to access the parts ...
Proceso de instalación y conexión. 2.1.1. Consideraciones generales. Para comenzar con la instalación del escáner, una vez introducido el CD en el ordenador ...
17 oct. 2016 - Gire el teléfono boca abajo y deslice hacia fuera el teclado.. Cuña de una herramienta de abertura de plástico donde el teclado se encuentra ...
Tips: • Blinds can be cleaned in place or taken down for cleaning. • By tilting the slats down to the almost closed position, you can clean most of the top surface.
position, you can clean most of the top surface of each slat. Tilting the slats up allows you to clean the bottom surface of each slat. For hard-to-remove dust and ...
end of the headrail, making sure the brackets will not interfere with the cord mechanism or other internal headrail parts. • When using a single center support ...
Esta guía detalla cómo retirar la placa base de su Nexus 4. HERRAMIENTAS: Phillips # 00 Destornillador (1). iFixit herramientas de la abertura (1). Spudger (1).