Sceptre X9 Komodo VII Video Motherboard Replacement
Sceptre X9 Komodo VII Video Motherboard. Replacement. This guide will remove and install the video motherboard. Escrito por: David Taylor. Sceptre X9 ...
Sceptre X9 Komodo VII Video Motherboard Replacement
ID de guía: 10840 - Borrador: 2014-01-28
Paso 3 — Board Cover
Using a #2 Phillips screwdriver, remove the six 7mm screws at the circled locations.
Paso 4
Pry the monitor using the plastic opening tool to release the clips holding the cover on.
There are four clips on each side, four on the top, and one on the bottom. You may hear a loud snapping noise when releasing the clips. Do not be alarmed, it is natural.
Once all the clips have been released, remove the cover by pulling it up.
Sceptre X9 Komodo VII Video Motherboard Replacement
ID de guía: 10840 - Borrador: 2014-01-28
Paso 6 — Video Motherboard
Use caution when removing the connectors as they can easily break when removing.
Disconnect the multi-pin connector at the top of the board by firmly grasping the connector and pulling to the side.
Disconnect the multi-pin connector that runs between the video motherboard and the power supply motherboard. Firmly grasp the connector and pull straight up.
A plastic opening tool can be used to assist in the removal of connectors.
Paso 7
Remove the two 3/16" hex head screws from the VGA connecter. Use a pair of needle nose pliers if a wrench is not available.
Sceptre X9 Komodo VII Video Motherboard Replacement
ID de guía: 10840 - Borrador: 2014-01-28
Paso 8
Remove the four 6.4mm #2 Phillips screws from the corners of the motherboard with a #2 Phillips screwdriver.
Paso 9
Lift the motherboard straight up to remove it from the back panel.
To reassemble your device, follow these instructions in reverse order. La versión más reciente de este documento fue generada en 2019-07-09 07:47:17 AM .
Press and hold the battery release button and slide the battery away from the Nokia logo.. Paso 2 â SIM card. Slide the SIM card lock away from the SIM card.
Remove three 5.5 mm T5 Torx screws from the back of the phone. ... After separating the sides, make sure there is a noticeable gap between the back case and ...
be plastic opening tools, PH #000 screwdriver and tweezers. With these prepared everything should be ready to start the replacement of the motherboard for the ...
Remove the five "F2" screws with a. Phillips #0 screwdriver.. Paso 4. Insert the plastic opening tool above the F1 key.. Apply upward pressure until the black ...
Escrito por: Neil Daniels. Fujitsu LifeBook N3510 ... Use a spudger to lift the back of the hinge cover on the left and right sides of the computer.. Paso 4. Lay the ...
Use un cubo de 13 mm para aflojar la abrazadera entre el silenciador y el tubo colector.. No es necesario quitar el perno, pero desea aflojar la abrazadera.
17 oct. 2016 - Gire el teléfono boca abajo y deslice hacia fuera el teclado.. Cuña de una herramienta de abertura de plástico donde el teclado se encuentra ...
Esta guía detalla cómo retirar la placa base de su Nexus 4. HERRAMIENTAS: Phillips # 00 Destornillador (1). iFixit herramientas de la abertura (1). Spudger (1).
Paso 5 — Tarjeta SIM. Utilice una herramienta de abertura de plástico, o la uña, para presionar la tarjeta SIM poco más profundo en su ranura hasta que oiga ...
Product Info: Ecuakaraoke Software Para Instalar En Computador O Pc Con Sistema Operativo De Microsoft Licencia nica. Para Un Solo Computador 7 Dvds Karaoke De Pistas Originales Para Cantar Los Temas Que Ms Te Gusten De. Tus Artistas Favoritos. Edici
Omega S.A. Barcelona. España. • Brown, T.; LeMay, H.; Bursten, B. (1998) ”Química la Ciencia ... Algunos elementos de los grupos. IA, IIA, IIIA, como así.
