Product Information_Air Screwdriver and Angle Wrench - Ingersoll Rand
Size air supply line to ensure tool's maximum operating pressure (PMAX) at tool ... circular arrow and defined as h=hours, d=days, and m=months of actual use.
EN Product Safety Information Intended Use: These tools are designed to install or remove threaded fasteners. For additional information refer to Product Safety Information Manual Form 04585006. Manuals can be downloaded from ingersollrandproducts.com
De originele instructies zijn opgesteld in het Engels. Andere talen zijn een vertaling van de originele instructies. Reparatie en onderhoud van dit gereedschap ...
Embrague de corte de suministro de aire 3.5 - 13 (0.39 - 1.5) .... mantenimiento de las herramientas sólo pueden realizarse en un centro de servicio autorizado.
Installation and Lubrication. Size air supply line to ensure tool's maximum operating pressure (PMAX) at tool inlet. Drain condensate from valve(s) at low point(s) ...
5C1-116 adjusting key or a 3/32" (2 mm) diameter hardened steel pin or rod into ..... la herramienta en la aplicación real y aumentando o disminuyendo el par.
Other languages are a translation of the original instructions. Tool repair and maintenance ...... fehlerhaft ist oder sich eine Verbindung löst. Siehe Zeichnung ...
... shown on the tool may result in hazardous situations including excessive speed, .... Refer to Product Information Manual for Model Specific Safety Information.
5 ω. Exhaust. The air-in and exhaust is explained in drawing 16606279 in page 2. Item No. Description. Item No. Description. 1. Cycle Count Sealing Set Screw.
An Air Angle Wrench, Screwdriver or Nut Runner is a compressed air powered tool that is used to .... reaction torques, or forces during start up and operation.
Exposure to high noise levels can cause permanent, disabling hearing loss and other problems, such as tinnitus (ringing, buzzing, whistling or humming in the ...
Non modificare questo utensile, i suoi dispositivi di sicurezza o i suoi ..... entsprechend den Empfehlungen in diesem Handbuch, um unnötige aus Lärm,.
Unscrew the Clutch Adjusting Hole Cover far enough to expose the clutch adjusting hole in the Clutch .... Las demás versiones son una traducción de las.
Retirez le carter, le support d'embout et l'ensemble d'embrayage de l'outil. Le carter d'embrayage a un filetage à gauche. 2. Avec un embout se trouvant dans le ...
Trykk inn bits for å engasjere clutchen, og roter deretter til sporet i justeringsskiven synliggjøres. 3. Sett inn en Philips skrutrekker nr. 1 i sporet for å vri mutterens ...
Depress bit to engage clutch, then rotate until notch in Adjustment Washer or is visible. 3. Insert No. 1 Phillips screwdriver in notch to turn gear teeth on Nut,. 4.
situations, could result in death or serious injury. • This tool is designed to be operated by a minimum of two persons. For additional information refer to Product ...
slang valt of een koppeling losraakt. Zie tekening 47132600 en tabel op pagina 2. De onderhoudsfrequentie wordt weergegeven in een cirkelvormige pijl met ...
Pour les travaux en hauteur, il est nécessaire de porter des casques de sécurité ... Porter toujours une protection acoustique pendant l'utilisation de cet outil.
... son número de referencia y no indican la salida de par real. .... sont des chiffres de référence et ne consistent pas une indication du couple de sortie réel. FR-1.
For models that include a power management system, the system allows ... Size air supply line to ensure tool's maximum operating pressure (PMAX) at tool inlet.
Estas herramientas eléctricas portátiles se han diseñado para aplicaciones de atornillado de juntas .... Cycle de travail : Modèles à 1200 tr/min et 2000 tr/min.
Modello/i. Stile. Avanti. Indietro. Tipo men-. Minu ft-lb (Nm) ft-lb (Nm) sioni to. 2115TIMAX. 25-230 [250 Max.] 280 [300 Max.] p Impugnatura Squadra 3/8” 1500.
