Menu
Casa
Añadir documento
iniciar sesión
Crear una cuenta
PNG Transparente
Casa
Añadir documento
iniciar sesión
Crear una cuenta
PNG Transparente
Mac Mini mediados de 2011 Sustitución de Cowling
fuera de la
disputa
asegurada a la caja exterior.. Extracción del tornillo de enfrentamiento no es necesario quitar el ventilador. Sólo es necesario elevar el ...
Descargar PDF
Imágenes PNG
4MB Größe
6 Downloads
34 vistas
comentario
Informe
Mac Mini Mid 2011 Cowling Replacement
Mac Mini Mid 2011 Cowling Replacement Plastic cowling covering the heat sink.
Escrito por: Walter Galan
© iFixit — CC BY-NC-SA
es.iFixit.com
Página 1 de 6
Mac Mini Mid 2011 Cowling Replacement
INTRODUCCIÓN Use this guide to remove the small molded plastic cowl used to direct cool air toward the heat sink.
HERRAMIENTAS: T6 Torx Screwdriver (1)
© iFixit — CC BY-NC-SA
es.iFixit.com
Página 2 de 6
Mac Mini Mid 2011 Cowling Replacement
Paso 1 — Bottom Cover
Place your thumbs in the depressions cut into the bottom cover.
Rotate the bottom cover counter-clockwise until the white dot painted on the bottom cover is aligned with the ring inscribed on the outer case.
You do not need to apply much downward pressure while turning. Paso 2
© iFixit — CC BY-NC-SA
es.iFixit.com
Tilt the mini enough to allow the bottom cover to fall away from the outer case.
Remove the bottom cover and set it aside.
Página 3 de 6
Mac Mini Mid 2011 Cowling Replacement
Paso 3 — Fan
Remove the two 11.3 mm T6 Torx screws securing the fan to the logic board near the antenna plate.
Lift the ear of the fan nearest the RAM up off the standoff secured to the outer case.
Paso 4
Removing the standoff screw is not necessary to remove the fan. You need only raise the fan enough to lift it off the standoff screw.
© iFixit — CC BY-NC-SA
es.iFixit.com
Página 4 de 6
Mac Mini Mid 2011 Cowling Replacement
Paso 5
Lift the fan out of the mini for enough clearance to access its connector.
Carefully pull the fan cables upward to lift the fan connector up out of its socket on the logic board.
Remove the fan.
Remove the single 3.5 mm T6 Torx screw securing the cowling to the heat sink.
Paso 6 — Cowling
© iFixit — CC BY-NC-SA
es.iFixit.com
Página 5 de 6
Mac Mini Mid 2011 Cowling Replacement
Paso 7
Lift the cowling from the end nearest the antenna plate.
Rotate the cowling away from the outer case and remove it from the mini.
La versión más reciente de este documento fue generada en 2017-10-16 11:53:32 PM .
© iFixit — CC BY-NC-SA
es.iFixit.com
Página 6 de 6
recomendar documentos
no hay documentos
×
Informe "Mac Mini mediados de 2011 Sustitución de Cowling"
Tu nombre
Email
Reason
-Select Reason-
Pornográfico
Difamatorio
Ilegal / Ilícito
Spam
Otros Términos de Servicio de Violación
Presentar una queja por derechos de autor
Descripción
×
iniciar sesión
Email
Password
Erinnere dich an mich
contraseña olvidada?
iniciar sesión
Our partners will collect data and use cookies for ad personalization and measurement.
Learn how we and our ad partner Google, collect and use data
.
Agree & Close