CADRE. ATTACHE. VIS DE CADRE. FLEURON. 2. ATTENTION : RISQUE D'INCENDIE. Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne. Utiliser les conducteurs d'alimentation supérieure à 90° ...
Outdoor GENERAL PRODUCT INFORMATION: This product is listed by one of the following “Nationally Recognized Testing Laboratory”
This product is suitable for wet locations.
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
This product may be dimmed with a low voltage electronic dimmer.
Use minimum 90°c supply conductors.
These fixtures are intended to be installed utilizing NEC compliant junction boxes.
1A
4
FINIAL
FRAME CLIP
1
NIPPLE
FRAME SCREW
2
3
1
NIPPLE
GLASS PANEL
4 HOUSING HOUSING
1
Install all glass panels by carefully sliding them into the housing and securing them using the clips.
2
Install the frame to the housing and secure it to the housing using the frame screws.
3
Follow enclosed supplement installation instructions for electrical and fixture installation onto house junction box.
4
Raise the housing up to the fixture so that the nipple exits through the top of the fixture and secure them together by screwing the finial onto the nipple.
5
For wet locations, caulk around the base of the fixture using waterproof construction sealant.
1
1.0
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c.
1A
4
FLEURON
CADRE CLIP
1
ATTACHE
VIS DE CADRE
2
3
1
ATTACHE
PANNEAU DE VERRE
4 LOGEMENT LOGEMENT
1
Installer tous les panneaux de verre en les faisant glisser avec précaution dans le logement et les fixer à l'aide des clips.
2
Installez le cadre sur le logement et le fixer au logement à l'aide des vis de cadre.
3
Suivez les instructions d'installation de suppléments fermés pour l'installation électrique et le luminaire sur une boîte de jonction.
4
Augmenter le logement jusqu'à le luminaire de sorte que le attache sort par le haut de le luminaire et les fixer ensemble en vissant le fleuron sur le attache.
5
Pour les endroits humides, calfeutrer autour de la base de l'appareil en utilisant une construction étanche étanchéité.
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c.
1A
4
FINIAL
MARCO CLIP
1
CONECTADOR
TORNILLO DEL MARCO
2
3
1
CONNECTADOR
PANEL DE VIDRIO
4 VIVIENDA VIVIENDA
1
Instalar todos los paneles de vidrio deslizándolos cuidadosamente en el alojamiento y fijan utilizando los clips.
2
Instale el marco de la vivienda y fijarlo a la vivienda con los tornillos del marco.
3
Siga las instrucciones de instalación de suplementos cerrados para la instalación eléctrica y el accesorio sobre la caja de junctura.
4
Elevar la vivienda hasta la lámpara para que el conectador sale a través de la parte superior de la lámpara y asegurarlos juntos atornillando el finial en el conectador.
5
Para lugares húmedos, calafatear alrededor de la base de la lámpara usando sellador de construcción a prueba de agua.
Secure the fixture to the post with the post screws making sure to neatly tuck in all wiring. ... Place the cover over the frame and secure it in place by screwing the finial onto the nipple ... Feiss reserves the right to ... A Generation Brands Com
Install all glass panels by carefully sliding them into the housing and securing them using the clips. Install the frame to the housing and secure it to the housing using the frame screws. Screw the lamps into the sockets. Refer to the label on the s
Fixer le cadre au logement à l'aide des vis de cadre. Placez le couvercle et la rondelle sur le attache et les fixer en vissant l'écrou moleté sur l'attache, puis vissez la boucle de luminaire sur l'attache. Suivez les instructions d'installation de
Fixer le cadre au logement à l'aide des vis de cadre. Placez le couvercle et la rondelle sur le attache et les fixer en vissant l'écrou moleté sur l'attache, puis ...
This product is safety listed for wet locations. For a complete list of dimmers, visit out website at www.Feiss.com. CAUTION RISK OF FIRE. -. This product must be ...
Screw the lamps into the sockets. Refer to the label on the socket for Max Wattage information. ... 7400 Linder Ave, Skokie, IL 160077. 800.969.3347 www.Feiss.
Connect the white fixture wire to the neutral power line wire with a wire nut. ... 4. 1. 1. 6. 7. 5. Londontowne Outdoor Flush Mount (LED). 1.1. OL11313-LED.
For Model OL12603 Only: Temporarily install the mounting plate to the junction box. For Model OL12603 Only: Mark the anchor hole locations on the mounting ...
System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations. -. Go to the main fuse box, ...
Headquarters/Eastern Distribution Center. 44 Harbor Park Drive. Port Washington, NY 11050. Central Distribution Center. 1600 Distribution Ct. Lithia Springs ...
Secure the frame to the housing using the frame screws. Place the washer and cover onto the nipple and secure them in place by screwing the knurled nut onto the nipple, then screw the ... All rights reserved. ... A Generation Brands Company.
Insert the glass panels into the shade, then secure them by installing the brackets using the screws and washers. Install the LED assembly to the top fixture using ...
Instalar temporalmente la placa de montaje a la caja de juntura. Marque las ubicaciones de los orificios de anclaje en la placa de montaje y retire la placa de montaje. Taladro agujeros de tamaño apropiado en los lugares marcados y instalar los ancla
This product is suitable for wet locations. This product may be dimmed with a low voltage electronic dimmer. This instruction shows a typical installation. 1. 2. 1A.
Insert the diffuser into the diffuser base, then install the diffuser cover to the bottom of the fixture and secure it in place with the cover screws. Connect the fixture ...
Insert the diffuser into the diffuser base, place the LED assembly on top of the diffuser, and secure it to the top of the housing using the LED assembly screws.
Install the diffuser by sliding it into the fixture from the bottom and secure with thumb screws. Place the cover onto the fixture and secure it using the cover screws.
luminaire et le fixer avec la petite vis de fixation à l'aide d'une clé Allen. Fixez le bras à la ... 555 Theodore Fremd Ave Suite B101 Rye, NY 10580. 800.969.3347.
Do not substitute any parts, leave parts out, or use any parts that are worn out or ... has a green or bare copper ground wire, connect the fixture's ground wire to it.
Mount the fixture base onto the mounting plate and secure it with the Allen screw using an Allen wrench. Install the shade by placing it over the shade base and ...
Headquarters/Eastern Distribution Center. 44 Harbor Park Drive. Port Washington, NY 11050. Central Distribution Center. 1600 Distribution Ct. Lithia Springs ...
System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations. -. Go to the main fuse box, ...
