un electricista profesional. Si el GFCI se dispara, restablézcalo. A continuación, inserte el comprobador de GFCI en el enchufe que desea comprobar. 0 Active el ...
battery, strike the back of the Probe sharply in the palm of your hand. The replacement battery can then be inserted. Use a 9 volt alkaline battery only. DO NOT ...
if Lynbrook. NY 11563-0329. Outside the USA. the local Amprobe representative will assist you. Above limited war-. ~ ranty covers repair and replacement of instrument only and no other obligation is stated or ... After measuring insulation resistance
Premere il tasto VOLTAGE, CURRENT, POWER o ENERGY secondo il tipo di analisi. 7. da eseguire. Per interrompere l'aggiornamento in tempo reale dei valori ...
auto power off 30 sec (Data store). 0Ë ... 50Ë C / 32Ë ...122Ë F. -20Ë ... 70Ë C / -4Ë ...158Ë F ... Mississauga, ON L4Z 1X9. Tel.: 877-AMPROBE (877-267-7623). Tel.
If there is no indication, voltage could still be ... Caution: If three phase equipment is being checked and one phase is open, the voltage is ..... Alta tensione.
No toque el terminal mientras la máquina está funcionando. Si lo hace corre el riesgo de ..... Tiempo diferencial Configura el tiempo diferencial del parámetro ...
156 (H) x 86 (L) x 38 (P) mm (6,1 x 3,4 x 1,5 po). Poids : ...... Reparationer i USA och Kanada som ej täcks av garanti ska skickas till ett Amprobe® Test Tools.
If the Tester is used in a manner not specified by the manufacturer, protection ... Use proper protective equipment as required by local or national authorities.
1. Press the POWER ON/OFF button once to turn on the instrument. 2. Selecting desired Measurement Mode a) After the instrument has been turned on, press.
Buy” section on www.amprobe.com for a list of distributors near you. ...... del conducto entre 0,001 y 9999 pies cuadrados o 928 m2; seguidamente, pulse la ...
Tools Service Center or to an Amprobe dealer or distributor. See Repair Section ..... carga ligera si se conectará a la línea un dispositivo pe- queño que utilice ...
Sensor (N.º de ref. 69087) ⦠Cable (N.º .... Remove the stem adapter from the sensor body by loosening the 1/4â ... The sensor connector is keyed with two slots.
ambiant (p. ex. passage d'une température haute à basse), il lui faut 30 secondes de réaction au capteur de CO2 et 30 minutes pour l'humidité relative. 3.
Licht de beugel (c) zorgvuldig op en druk de batterijhouderdeksel(a) naar buiten. 2. Vervang de gebruikte batterij door twee nieuwe AAA batterijen. 3. Zet het ...
or -50°C to 1550°C. The IR-750 / IR-750-EUR is perfect for demanding quality and process control applications with extremely high ..... Possible dead battery.
la condición más peligrosa, y la máquina debe diseñarse para detener automáticamente el calentamiento .... diferenciales de resistencia entre tres cables.
NC Operation: SS Floats: Witness mark (round circle) down. .... under normal use and service for a period which is equal to the shorter of one year from the.
Since some states or countries do not allow the exclusion or limitation of an ... by the following: your name, company's name, address, telephone number, and proof of ... charge. please check the “where to buy” section on www.amprobe.com for a list o
oR STAUToRY - inCLUDinG iMpLieD wARRAnTieS of fiTneSS foR A .... Any time you turn the unit off and turn it back on, it will go through the warm-up process.
For the pressure test of ball valves, the same instructions apply as for the piping ... of a collection container). ... Store metering ball valve in open lever position. 5.
