Secure the mounting plate to the junction box. Connect the fixture to a ... Connect the black fixture wire to the hot power line wire with a wire nut. Place the fixture ...
Ceiling GENERAL PRODUCT INFORMATION: These fixtures are intended to be installed utilizing NEC compliant junction boxes. Incandescent lamps may be dimmed with a standard incandescent dimmer. LED lamps may be dimmed with a LED dimmer. Consult lamp manufacturer for additional information.
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
This instruction shows a typical installation.
Use minimum 90°c supply conductors.
This product is safety listed for damp locations.
1A
JUNCTION BOX
3
4 MOUNTING PLATE
MOUNTING PLATE STUD CAP NUT
COUPLER
5 LAMP
6
7 THREADED PIPE
DIFFUSER WASHER
8
HEX NUT
9
FINIAL 1
Secure the mounting plate to the junction box.
2
Connect the fixture to a suitable ground in accordance to local electrical codes.
3
Connect the white fixture wire to the neutral power line wire with a wire nut.
4
Connect the black fixture wire to the hot power line wire with a wire nut.
5 1
Place the fixture base onto the mounting plate studs and secure them in place by screwing the cap nuts onto the studs.
6
Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information.
7
Screw the threaded pipe to the coupler.
8
Place the diffuser and washer onto the threaded pipe and secure them in place by screwing the hex nut onto the pipe.
9
Screw the finial onto the threaded pipe. 1
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c. 1A
BOÎTE DE JONCTION
3
4 PLAQUE DE MONTAGE
GOUJON DE MONTAGE ECROU CAPUCHON
COUPLEUR
5 AMPOULE
6
7 TUYAU FILETÉ
DIFFUSEUR RONDELLE
8
ECROU HEX
9
FLEURON 1
Fixer la plaque de montage sur le boîte de jonction.
2
Connecter le luminaire à un terrain approprié conformément aux codes électriques locaux.
3
Connecter le fil blanc de luminaire pour le fil de ligne à neutre avec un écrou de fil.
4
Connecter le fil noir de luminaire au fil de la ligne d'alimentation hot avec un écrou de fil.
5 1
Placez la base de luminaire sur les goujons de montage et fixez-les en place en vissant les écrous sur les goujons.
6
Vissez l’ampoules dans les douilles. Reportez-vous à l'étiquette sur la douille de lampe pour information Max Wattage.
7
Vissez le tuyau fileté au coupleur.
8
Placez le diffuseur et la rondelle sur le tuyau fileté et fixez-les en place en vissant l'écrou sur le tuyau.
9
Visser le fleuron sur le tuyau fileté.
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c. 1A
CAJA DE JUNCTURA
3
4 PLACA DE MONTAJE
ESPARRAGO DE MONTAJE TUERCA CAPUCHON
ACOPLADOR
5 BOMBILLA
6
7 TUBO ROSCADO
DIFUSOR ARANDELA
8
TUERCA HEX
9
FINIAL 1
Fije la placa de montaje a la caja de junctura.
2
Conecte la lámpara a una puesta a tierra adecuada de acuerdo a los códigos eléctricos locales.
3
Conecte el cable blanco de la lámpara al cable de la línea de alimentación neutra con una tuerca para cable.
4
Conecte el cable negro de la lámpara al cable de la línea eléctrica caliente con una tuerca para cable.
5 1
Coloque la base de la lámpara en los esparragos de montaje y fijarlos en su lugar atornillando las tuercas capuchon en los esparragos.
6
Atornille las bombillas en los enchufes. Consulte la etiqueta en el zócalo de la lámpara para obtener información Max Potencia.
7
Atornille el tubo roscado al acoplador.
8
Coloque el difusor y la arandela en el tubo roscado y fijarlos en su lugar enroscando la tuerca hexagonal en el tubo.
Install the mounting plate to the junction box with junction box screws (not provided) ... screws to mount the fixture later. ... Use minimum 90°c supply conductors.
For Model OL13603 Only: Temporarily install the mounting plate to the junction box. For Model OL13603 Only: Mark the anchor hole locations on the mounting ...Falta(n):
junction boxes. This product is safety listed for damp locations. This product may be dimmed with a standard incandescent dimmer. This instruction shows a ...
Connect the white fixture wire to the neutral power line wire with a wire nut. ... Place the shade onto the socket and secure it in place by screwing the collar nut ...
Connect the black fixture wire (round and/or smooth) to the hot power line ... Place the shade inside of the decorative ring and secure it in place using the tabs.
Coloque la base de la lámpara en los esparragos de montaje y seguro en su lugar atornillando las tuercas capuchon en los esparragos. Atornille las en los ...
For your protection, read carefully before proceeding with installation. To be installed by a qualified electrician. Heavy duty gloves should be worn to protect hands from sharp edges. Protective eye wear should be worn to prevent injury to eyes. 1.
Connect the white fixture wire to the neutral power line wire with a wire nut. Connect ... tightening the fixture screws into the nuts. 1. 2 ... Feiss reserves the right to.
Screw the side of the threaded nipple with the pre-installed nut into the fixture base. Install the bottom shade ring and diffuser, then secure them in place with the ...
junction boxes. This product is safety listed for damp locations. This instruction shows a typical installation. Secure the mounting plate to the electrical box with ...
Place the shade and spacer over the socket, then secure them in place by tightening the collar nut. Screw the lamp into the socket. Refer to the label on the ... Conecte el cable negro de la lámpara (redonda y / o suave) al cable de la línea eléctric
AGUJERO DEL TORNILLO. 3 ... Conecte el cable negro del conductor al cable de la línea eléctrica caliente con una tuerca para ... los agujeros de los tornillos.
NOTE: The smaller the number of wire gauge means it is a thicker wire. 2. PARTE 4 ... paint job, then cover the speaker grille with a coat of anti-rust paint. NOTE: Prior to .... strands. 2. Attach the speaker wire to the Red/Black speaker terminals.
fil devra passer à l'intérieur des murs, dans le grenier ou dans le vide sanitaire. •. On doit toujours se procurer un peu plus de fil qu'il n'en faut pour l'installation.
Fig.2 Wiring. PREPARATION. 1. Shut off the power at the circuit breaker and remove existing fixture, including the mounting hardware. 2. Carefully unpack your ...
Next, slip the glass ring (2) inside of the brackets (B) and over the lip. (L) on roof (R). Now align the holes (H) in brackets (B) with the threaded holes (T) in glass ...
Place the pipe cover, spacer, steel washer, rubber washer, shade, rubber washer, and steel washer onto the threaded pipe in that order, then secure them in ...
FIXTURE. FIXTURE BASE. 5. 4. 5. 6. 7. 8. 8. 8. MOUNTING PLATE SCREW ... Conecte el cable blanco de la l mpara al cable de energía de la línea neutral con ...
This product is safety listed for damp locations. This product may be dimmed with a standard incandescent dimmer. This instruction shows a typical installation.
Connect the black fixture wire to the hot power line wire with a wire nut. ... Connecter le luminaire à un terrain approprié conformément aux codes électriques ...
Connect the black fixture wire to the hot power line wire with a wire nut. Place the fixture ... applicable installation code by a person familiar with the construction ...
