Cable Management Horizontal Panels and Racks INSTALLATION INSTRUCTIONS ©Panduit Corp. 2001

Printed in U.S.A.

1. PART NUMBERS Horizontal Cable Management WMP1 WMPF1 WMPSH WMPFSH WMPLS WMPLFS WMPS, WMPS23 WMPFS, WMPFS23

Racks

WMPH2H WMPHF2H WMPH2, WMPH223 WMPHF2, WMPHF223 WMPH3H WMPHF3H WMPH3, WMPH323 WMPHF3, WMPHF323

CMR19X47 CMR19X84 CMR23X84 CMR19X26

2. RACK INSTALLATION 2.1

ASSEMBLE RACK

2.1.1

Install top angle to upright channels. Finger tighten only.

2.1.2

Install the base angles to the vertical upright channels. Finger tighten only.

2.1.3

Stand rack upright. Square the upright channels with the base using a carpenter square. Completely tighten all bolts. See the diagram below for dimensions needed to locate the rack and the vertical cable management.

2.2

MOUNT RACK TO FLOOR

2.2.1

Securely mount the rack to the floor using the appropriate hardware based on the floor construction (concrete, raised floor, or wood).

3. HORIZONTAL CABLE MANAGEMENT INSTALLATION 3.1

ATTACH HORIZONTAL CABLE MANAGEMENT PANEL

3.2

Use four (4) 1/4”- 20 x 1/2” screws to fasten the horizontal LOCATION GUIDE Dimensions in () parenthesis are for 6” Vertical Cable Management 20.25 = 19” rack 24.25 = 23” rack

1.25

20.25 = 19” rack 24.25 = 23” rack

4.57

3.56 12.5

3.00 3.69

1.25

16.00 = 19” rack 20.00 = 23” rack

9.25 (11.06)

16.00 = 19” rack 20.00 = 23” rack

2.12

For Technical Assistance call:

2.12

888-506-5400, Ext. 6914

PN220A Page 1 of 3

INSTALLATION INSTRUCTIONS management between the racks.

BREAK OFF FINGERS OF VERTICAL MANAGEMENT WHERE IT MEETS THE HORIZONTAL MANAGEMENT

3.3

VERTICAL TO HORIZONTAL JUNCTION

3.3.1 Break the fingers off of the vertical panel where it meets the horizontal panel. FRONT

3.3.2 Route the cables through the strain relief brackets as shown. 3.3.3 Place snap in wire retainer between duct fingers.

BACK THREAD CABLES THROUGH THE STRAIN RELEIF BRACKET

3.3.4 Turn retainer 90°. 3.3.5 Push retainer to end of fingers until it snaps in place.

4. DATA-PATCH 110 STYLE PATCH PANEL #12 - 24 X 1/2” SCREWS

CABLE CAPACITY CHART

SNAP IN WIRE RETAINER (WR5) IS INCLUDED IN THE VERTICAL PANEL KITS.

Part Number WMP1 WMPF1 WMPFS, WMPFS23 WMPH2, WMPH223 WMPHF2, WMPHF223 WMPHF3, WMPHF23 WMPH3, WMPH323 WMPLFS WMPLS WMPS, WMPS23

UTP Cable .187” Dia. Front Back

ScTP or CAT 6 Cable Fiber .25” Dia. 3mm Front Back Front Back

72 72

72 36 36

36 72 72

36

18

36

72

72 36

36 72

72

36

72

192

96

480

192

192 96

96

24 24

12 24 12

24 12 24

24

36

36 18

18 36

36

480

72

72

480

NOTE: DUCT BASED ON 40% FILL CAPACITY

For Technical Assistance call:

888-506-5400, Ext. 6914

PN220A Page 2 of 3

INSTALLATION INSTRUCTIONS

TERMINATION

WMPH2

BLOCK 2

BLOCK 24 BLOCK 23 SLOT 23

BLOCK 1

WMPH2

SLOT 1

BLOCK 3

4.1

When mounting two 24 port rows of patch panels concurrently or a single 32, 48, or 64 port panel:

4.1.1

To terminate the first block, run the cable from the first Cable Management Panel slot directly to the first block.

4.1.2

Repeat steps 5.1.1 and 5.1.2 with the adjacent columns until each block is terminated. (Due to space constraints, the cable for blocks 1 and 2 should be double stacked in slot 1).

WMPH2 SLOT 23

SLOT 1 BLOCK 2 BLOCK 1 BLOCK 26 BLOCK 25

BLOCK 24 BLOCK 23 BLOCK 48 BLOCK 47 SLOT 23

WMPH2

BLOCK 27

SLOT 1

4.2

When mounting two 48 port rows of patch panels concurrently or a single 96 port panel:

4.2.1

To terminate the first block (BLOCK 25), run the cable from the first Cable Management Panel slot directly to block 25.

4.2.2

To terminate the second block (BLOCK 27), run the cable from the third cable management panel slot to block 27.

4.2.3

Repeat steps 4.2.1 to 4.2.2 for the remaining blocks in the bottom row, remembering to leave an empty slot between each terminated block.

4.2.4

To terminate the second, third, and forth row start at block 26 from slot 1. Continue with the rest of the blocks but run the cable through the even numbered slots.

4.3

Refer to the DATA-PATCH 110 Style Patch Panel Instruction sheet for Punch Down Block Termination. 10500 West 167th Street Orland Park, IL 60467 Phone: 888-506-5400, Ext. 6914 FAX: 708-444-6993

NETWORK CONNECTIVITY GROUP

Email:[email protected] Web site: www.panduit.com/ncg

WORLDWIDE SUBSIDIARIES AND SALES OFFICES

PN220A Page 3 of 3