... the lamp socket for Max Wattage information. Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box. 1.
Chandelier GENERAL PRODUCT INFORMATION: These fixtures are intended to be installed utilizing NEC compliant junction boxes.
CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
This product is safety listed for damp locations only. Incandescent lamps may be dimmed with a standard incandescent dimmer. LED lamps may be dimmed with a LED dimmer. Consult lamp manufacturer for additional information.
Use minimum 90°c supply conductors.
1A 7
FRAME
3
1
STEM
6
LAMP
5
CANDLE TUBE SOCKET
1 FIXTURE
3 CUP
4 FINIAL 1
Screw the stem to the fixture, then screw the stem to the frame.
2
Open the folded arms evenly.
3
Install the fixture arms to the fixture frame and secure them together using Allen screw.
4
Install the cover to the bottom of the fixture and secure it in place using the finial
5
Install the candle tubes by slipping them through the sockets.
6
Screw the lamps into the sockets. Refer to the label on the lamp socket for Max Wattage information.
7
Follow enclosed supplement installation instructions for electrical and fixture installation onto house outlet box.
1
1.0
ATTENTION : RISQUE D'INCENDIE Ce produit doit être installé conformément au code d'installation en vigueur par une personne familière avec la construction et l'exploitation du produit et les risques qu'il entraîne.
Utiliser les conducteurs d'alimentation supérieure à 90° c. 1A 7
CADRE
3
1
TIGE
6
AMPOULE
5
TUBE BOUGIE
DOUILLE
1 LUMINAIRE
3 COUPE
4 FLEURON 1
Vissez la tige sur le luminaire, puis vissez la tige à le cadre.
2
Ouvrez les bras pliés uniformément.
3
Installez les bras de luminaire à le cadre de luminaire et fixez-les ensemble à l'aide des vis Allen.
4
Installer le couvercle vers le bas de luminaire et de le fixer en place à l'aide de finial
5
Installez le tubes de bougie en les glissant à travers le douille.
6
Vissez les ampoules dans les douilles. Lire l'étiquette sur la douille de lampe pour informations Max Wattage.
7
Suivez supplément ci-joint des instructions électriques et installation d'accessoires dans la boîte de prise de maison.
2
PRECAUCIÓN: RIESGO DE INCENDIO Este producto debe instalarse de acuerdo con el código de instalación aplicable por una persona familiarizada con la construcción y operación del producto y los riesgos que conllevan.
Utilizar conductores de suministro mínimo 90° c. 1A 7
MARCO
3
1
TALLO
6
BOMBILLA
5
TUBO DE VELA
ENCHUFE
1 LÁMPARA
3 COPA
4 FINIAL 1
Atornillar el tall y la lámpara, luego atornillar el tallo a la asamblea superior.
2
Abrir los brazos cruzados de manera uniforme.
3
Instale los brazos de la lámpara a el marco de la lámpara y fíjelos juntos con tornillos Allen.
4
Instale la cubierta hacia la parte inferior de la lámpara y asegurarlo en su lugar usando el finial.
5
Instale el tubo de vela deslizándolo a través de el enchufe.
6
Atornille la bombilla en el enchufe. Consulte la etiqueta en el zócalo de la lámpara para obtener información de Max Wattage.
7
Siga las instrucciones de instalación incluido suplemento para eléctricos y instalación de la lámpara en caja de salida de la casa.
Allier 1 Light Chandelier. 1.1. F2952-1-F2953-1. Chandelier. F2952/1, F2953/1_. G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be ...
For quiet and efficient operation, long life, and attractive appearance - lower or remove grille and vacuum interior of unit with a dust- ing brush attachment.
Installez les bras de luminaire à le cadre de luminaire et fixez-les ensemble à l'aide des vis de luminaire. Installer les tubes de bougie en les glissant à travers ...
2016 Feiss.All rights reserved.The "Feiss" graphic is a registered trademark of Feiss. Feiss reserves the right to change specifications for product improvements ...
Feed the cord through the decorative ring and stem, then screw the stem ... Install the fixture arms to the ring as shown using the Allen wrench and Allen screws.
Temporarily install the mounting plate to the junction box. Mark the anchor hole locations on the mounting plate and remove the mounting plate. Drill appropriate size holes at the marked locations and install the anchors. Secure the mounting plate to
10/08 P/N 030-1050 Rev. A ... 10. Install in accordance with all national and local electrical codes. 11. ... Other fan-speed controls (-LFSQ) do not require.
Page 1. MODEL QTXN110SL. HUMIDITY SENSING. FAN / LIGHT / NIGHT LIGHT. READ AND ..... Alimente la unidad con la tensión de línea y el cable eléctrico ...
a small hole (1/16”) and probe into the ceiling with a wire. 2. Locate the joists. Drill a starter hole in the ceiling between the joists. 3. To exactly locate the edge of ...
G. P. I. : ENERAL RODUCT NFORMATION. These fixtures are intended to be installed utilizing NEC compliant junction boxes. This product is safety listed for dry locations only. This product may be dimmed with a standard incandescent dimmer. This instru
Pasar los cables de la lámpara a través del dosel y atornille el dosel en la asamblea de tallo. Conecte la lámpara a una tierra apropiada de acuerdo a los ...
jonction. Suspendez les cristaux comme indiqué sur le dessin. Se référer au tableau de cristal pour l'identification de cristal. DOUILLE. BOUCLE DE LUMINAIRE.
Place the shade onto the socket and secure it in place by screwing the collar nut ... de suplementos cerrados para la instalación eléctrica y el accesorio sobre la ...
Place the shade and spacer over the socket, then secure them in place by screwing the shade collar nut onto the socket. Repeat for all shades. Screw the lamps ...
Selon votre choix de montage (chaîne ou semi-encastré), suivez les instructions d'installation de suppléments fermés pour l'installation électrique et appareil sur ...
Feed the cord through the stem and screw it onto the socket assembly. Assemble the spun pan by securing ... CAUTION - RISK OF FIRE. This product must be ...
Connect the black fixture wire (round and/or smooth) to the hot power line wire with a wire ... Refer to the label on the lamp socket for Max Wattage information. 1.
Place the diffuser onto the threaded pipe and secure it in place by screwing on the finial of your choice. Secure the mounting plate to the electrical box with two ...
Determine la altura deseada de la lámpara alimentando el cable a través del dosel y moviendo el cable hacia arriba o hacia abajo. Coloque el cable entre las ...
Feed the cord through the decorative ring and stem, then place the decorative ring onto the fixture and screw the stem onto the fixture. Feed the cord through the arm assembly, hex nut, decorative ring, and fixture loop, then secure the arm assembly
Connect the black fixture wire (round and/or smooth) to the hot power line wire ... If necessary, place the shade ring onto the shade so that it rests as shown, then ...