Documento no encontrado! Por favor, inténtelo de nuevo
Martin® Idler Conversion Kit
operating at speed over 700 fpm (3.5 m/sec) or conveyors less than 50 ft ... 10. (3048). 37135-B120. 11. (3353). 37135-B132. 12. (3568). 37135-B144. Each P/N ...
Martin® Idler Conversion Kit Eliminate Sag, Spillage, and Material Entrapment Improve Belt Support with Martin® Slider Bars. The Martin® Idler Conversion Kit improves a conveyor’s belt support system, stabilizing the line, improving sealing, and preventing spillage. This simple kit links two more troughing idler frames, replacing the wing rollers with Martin® Slider Bars.
BENEFITS
PROBLEMS
•
Stable Belt Line Improves Sealing No more sag, no more spillage. Edge sealing systems work more effectively on stable belt line.
•
Prevents Entrapment Damage Without sag, there’s no risk of material becoming wedged in pinch point to gouge belt.
Entrapped material gouges belt cover, shortening belt life.
•
Economical Conveyor Upgrade Reuse existing idler frames and center rollers for a cost-conscious system improvement.
Stable sag-free belt line allows improved sealing for reduced spillage and reduced maintenance problems.
•
Reduces Maintenance No adjustment necessary; no lubrication required.
•
Low Friction Surface Improve belt support without increasing drive power requirements.
•
Flexible Placement Custom-length bars improve belt support points where conveyor needs it most, including tight spaces.
•
Simple to Install Replace wing rollers easily; kit conforms to wide range of idler manufacturers.
Belt sag between idlers allows spillage, creating maintenance problems, cleanup costs, and regulatory issues.
TECHNICAL DATA SHEET CONVERSION KIT Select by belt width Belt Width in. (mm)
Slider Bar
P/N
Each Kit Includes Conversion Clamp
24
(610)
37135-K24
30
(762)
37135-K30
36
(914)
37135-K36
42
(1067)
37135-K42
48
(1219)
37135-K48
54
(1372)
37135-K54
60
(1524)
37135-K60
66
(1676)
37135-K66
72
(1829)
37135-K72
84
(2134)
37135-K84
96
(2438)
37135-K96
Conversion Bracket Two Idler Conversion Brackets (enough for one idler set). Two or four Conversion Clamps (to hold support bars to Conversion Brackets. Quantity depends on whether belt width requires one or two bars per side of cradle).
SLIDER BAR Select by length of bar required
Two Bars per side start at 48” belt width.
Bar Length ft. (mm)
TO ORDER: Measure distance supported and count the idlers to be converted. Example
Correct Order
Belt Width
30 in. (762 mm)
Distance to be Converted (Ea. Side)
32 ft. (9.75 m)
Number of Idlers to convert:
Coversions Kit: P/N 37135-K30
Support Bars: P/N 37135-B96
8
Quantity: 8
Quantity: 8
P/N
3
(914)
37135-B36
4
(1219)
37135-B48
5
(1424)
37135-B60
6
(1829)
37135-B72
7
(2134)
37135-B84
8
(2438)
37135-B96
9
(2743)
37135-B208
10
(3048)
37135-B120
11
(3353)
37135-B132
12
(3568)
37135-B144
Each P/N is one bar; order enough bars for both sides of each cradle. Note if cradles need one bar or two bars per side.
during the first several cleaning cycles. California lists .... the orifice from falling out of the socket during .... numbers in the space below to save time in the event.
Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions. If you cannot reach your gas supplier, call the fire department.
piping system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/ ...Falta(n):
test pressures in excess of 1/2 psig (3.5 kPa). b) The appliance must be isolated from the gas supply piping system by closing its individual manual shut-off.
certain the propane gas tank is equipped with its own high pressure regulator. .... Some yellow streaking in the flame is normal during the initial start-up.
Do not store or use combustible materials, gasoline or other flammable vapors and liquids in the ... call the fire department. Installation and must be performed.
amplified speaker and broadcasts the signal received on the signal lines. In the slave (SLA) mode, the intercom acts as a microphone and transmits audio,.
OWNER: Please retain these instructions for future reference. ... Note: The arrow on the back of the regulator must point in ... Snap the stem back in place in this.
This indicates that death or serious injuries may occur as a .... stem while pulling it from the metal cap.”) ... position inserting it into the indent in the metal cap.The.
See Before. You Begin chapter on previous page for .... 11. Step 4 - Convert valves for LP gas. The bypass jet on each valve must be adjusted. Your cooktop ...
Remove and discard the bracket, friction ring (3), and cartridge (4) from the valve body. ... Gire el cartucho (1) de manera que la palabra “UP” (2) aparezca encima. ... For back to back or reverse installations (hot on right and cold on left): Rotat
Instalación y Ajuste del Pomo de Temperatura. El no hacerlo puede causar lesión. Installation et réglage du bouton de température. Il y a risque de blessure si ...
6 nov. 2017 - Aspectos prácticos», Hammurabi, 2013. Autora de «Violenc ia. Familiar», Hammurabi, 2015. Autora de «La Gran Telaraña», «Violencia contra la Mujer con una Mirada de Género», «Me Gusta Escribir», Barcelona, 2016. Disertante en Congresos y
Montaje del Lado Derecho. Ubicación de Montaje de la ..... La última X indica el material: acero dúctil (en blanco) o acero inoxidable. (S). **Las dos primeras XX ...
a la contaminación del material, fallo del usuario al no inspeccionar, mantener y cuidar ... Materiales necesarios. 1 ..... resistencia de las hojas contra la banda.
Martin Engineering por el presente documento rechaza cualquier responsabilidad por daños debidos a la contaminación del material, fallo del usuario al no inspeccionar, mantener y cuidar razonablemente del equipo, lesiones y daños causados por el uso
IMPORTANTE. No utilice el hierro ángulo o anillo de soporte para fijar el ..... (s) en la tabla correspondiente a continuación y siga los pasos en la columna.
Martin Engineering por el presente documento rechaza cualquier responsabilidad por daños debidos a la contaminación del material, fallo del usuario al no inspeccionar, mantener y cuidar razonablemente del equipo, lesiones y daños causados por el uso
IMPORTANTE. No utilice el hierro ángulo o anillo de soporte para fijar el ..... (s) en la tabla correspondiente a continuación y siga los pasos en la columna.