IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information and instructions concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials, and proper lamping. Do not install in areas subject to combustible vapors or gases. Before wiring to power supply and during servicing or relamping, turn off power at fuse or circuit breaker. All servicing or relamping must be performed by qualified service personnel. Product must be grounded to avoid potential electric shock or other potential hazard. Product must be mounted in locations and at heights and in a manner consistent with its intended use, and in compliance with the National Electrical Code and local codes. The use of accessory equipment not recommended by the manufacturer or installed contrary to instructions may cause an unsafe condition. Do not block light emanating from product in whole or part, as this may cause an unsafe condition. Do not allow items such as drapes, curtains, screens or the like to come into contact with the product or to block light from the product, as this may cause an unsafe condition.

INSTALLATION INSTRUCTIONS TA120E

WARNING - IF ANY SPECIAL CONTROL DEVICES ARE USED WITH THIS FIXTURE, FOLLOW THE INSTRUCTIONS CAREFULLY TO ASSURE FULL COMPLIANCE WITH N.E.C. REQUIREMENTS. IF THERE ARE ANY QUESTIONS, CONTACT A QUALIFIED ELECTRICAL CONTRACTOR.

*******************************************************************************************************************************

4

www.prescolite.com

*******************************************************************************************************************************

1

8

3

2

CAUTION:- All Glass is Fragile, use care when Handling Lamp. 1.- Install the Fixture Housing (1) in the Ceiling (2) according to the instructions supplied with the Fixture. Replace Wingnut (8) inside Fixture Housing with fastener furnished with Eyeball.

2.- Lower the Socket (3) and compress the Socket Spring (4) while inserting the Socket into the Trim Socket Opening (5), then release.

5

3.- Orient the Trim (6) in the Housing with the Eyeball (7) aimed in the desired Lamp direction. 4.- Push upward until Trim is flush with Ceiling.

6

7

5.- Install the proper Lamp (not furnished) from front of trim as per the wattage Label inside Housing. Tilt Eyeball to adjust Lamp position.

Mode de montage et d'installation ATTENTION:

Prendre soigneusement connaissance de ces instructions et couper l'electricite a l'arrivee principale avant de proceder a l'installation.

************************************************************************************************************************************************************************ AVERTISSEMENT: SIDES DISPOSITIFS DE CONTROLE SPECIAUX SONT UTILISES EN CONJONCTION AVEC CE LUMINAIRE, SUIVRE SCRUPULEUSEMENT CES INSTRUCTIONS POUR ASSURER LA CONFORMITE N.E.C. POUR TOUTE ASSISTANCE SUPPLEMENTAIRE, DEMANDER CONSEIL AUPRES D'UN ELECTRICIEN QUALIFIE. ************************************************************************************************************************************************************************ AVERTISSEMENT: Le verre est fragile; maniez la lampe avec soin. 1- Installez le boítier de la lampe (1) au plafond (2) d'aprés les instructions qui accompagnent la lampe. 2- Abaissez la douille (3) et resserrez le ressort de douille (4) tout en insérant la douille dans l’ouverture de la douille de décoration (5), ensuite láchez. 3- Adjustez l’anneau décoratif (6) dans le boítier avec le globe (7) orienté vers la direction désirée. 4- Poussez en haut jusqu’á ce que l’anneau décoratif soit á ras du plafond. 5- Installez l’ampoule qui convient (non fournie) du devant de l’anneau décoratif selon l’étiquette de wattage dans le boítier. Faites pencherle globe pour ajuster la position de la lampe.

Instrucciones de ensamblado e instalacion ************************************************************************************************************************************************************************ ADVERTENCIA: SI CON ESTE APLIQUE SE USAN DISPOSITIVOS DE CONTROL ESPECIALES, DEBE SEGUIR LAS INSTRUCCIONES DETALLADAMENTE PARA GARANTIZAR EL CUMPLIMTENTO ESTRICTO CON EL CODIGO NACIONAL DE ELECTRICIDAD (N.E.C.). SI TIENE PREGUNTAS, COMUNIQUESE CON UN ELECTRICISTA CALIFICADO. ************************************************************************************************************************************************************************ ADVERTENCIA: El vidrio es frágil; tenga cuidado en manipular la lámpara. 1- Instale la caja de lámpara (1) en el techo (2) conforme a las instrucciones incluÌdas con la lámpara. 2- Baje el portalámparas (3) y comprima el resorte del portalámparas (4) mientras introducir el portalámparas en la apertura del portalámparas del adorno (5), luego suelte. 3- Oriente el anillo de adorno (6) en la caja con el globo (7) en la posición deseada. 4- Empuje hacia arriba hasta que el anillo de adorno esté a ras del techo. 5- Instale la bombilla apropiada (no incluída) de enfrente del anillo de adorno según la etiqueta dentro de la caja que indica la potencia en vatios. Incline el globo de ojo para cambiar la posición de la lámpara.

101 Corporate Drive • Spartanburg, SC 29303 With representatives offices in principal cities throughout North America. Copyright 2005, 11/05 revision, All Rights Reserved - Printed in U.S.A.

Hours: 8am - 5pm ET

de comenzar la instalacion, lea las instrucciones PRECAUION: Antes detalladamente y desconecte la electricidad desde el cortacircuitos principal.

• Prescolite TollFree Technical Support 1.888.PRS.4TEC •

InstructionSheet

Part No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .02379800