Installation Instructions

2 PREPARING THE OPENING (FOR INDOOR USE ONLY)

3 ELECTRICAL REQUIREMENTS

See the Illustrations for all rough dimensions. The range may be placed with 0” clearance at the side cabinet.

27” Drop In Ranges

Wall

In Canada, call 1.800.561.3344 or visit www.GEAppliances.ca Read these instructions completely and carefully.

• ,03257$17³ Save these instructions for local inspector’s use.

• ,03257$17³ Observe all governing

codes and ordinances. • Note to Installer – Be sure to leave these instructions with Consumer.

approved junction box. A plug and receptacle is NOT permitted on these products.

FOR YOUR SAFETY:

WARNING

• •

Tip-Over Hazard A child or adult can tip the range and be killed. Install the anti-tip bracket to the wall or floor. Engage the range to the anti-tip bracket by sliding the range back such that the foot is engaged. Re-engage the anti-tip bracket if the range is moved. Failure to do so can result in death or serious burns to children or adults.

If you did not receive an anti-tip bracket with your purchase, call 1.800.626.8774 to receive one at no cost. (In Canada, call 1.800.561.3344.) For installation instructions of the bracket, visit: www.GEAppliances.com. (In Canada, www.GEAppliances.ca.)

Anti-Tip Bracket Kit Included

WARNING Before beginning the installation, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

MATERIALS YOU MAY NEED

TOOLS YOU MAY NEED

Junction Box Wire Nuts Strain Relief Clamp for 1/2” Conduit

1/8” Drill Bit and Electric or Hand Drill Phillips Screwdriver Wire Strippers Hand or Saber Saw

1 REMOVE PACKAGING MATERIALS

Failure to remove packaging materials could result in damage to the appliance. Remove all packing parts from oven, racks and heating elements. Remove protective film and labels on the outer door and control panel. Also, remove plastic on trims and panel and all tape around the oven. Open oven door and remove literature pack and oven racks. Remove the bottom trim from the side of the oven. It will be installed at the end of the installation process. The trim is wrapped separately in a plastic bag which also contains the five screws to secure the bottom trim and the 4 anti-tip screws used to secure the product to the countertop. The plastic bag is taped to the side of the unit.

5 4-WIRE INSTALLATION

Before–Power Cord and Conduit

WARNING: The neutral wire of the

supply circuit must be connected to the neutral terminal located in the lower center of the terminal block. The power leads must be connected to the lower left and the lower right terminals of the terminal block. The grounding lead must be connected to the frame of the range with the ground plate and the green ground screw.

Ground strap Terminal block

or

Ground strap

FOR POWER CORD INSTALLATION A. Remove the 3 lower terminal screws from the terminal After–Power block. Remove the ground screw and ground plate and retain them. Cut and discard the ground strap. DO NOT DISCARD ANY SCREWS. B. Insert the one ground screw into the power cord ground wire Terminal terminal ring, through the ground plate and into block the frame of the range. C. Insert the 3 terminal screws (removed earlier) through each power cord terminal ring and into the lower terminals of the terminal block. Be certain that the center wire (white/neutral) is connected to the center lower position of the terminal block. Ground Tighten screws securely into the terminal block. screw

Neutral terminal

9/16” min. flat

Countertop

WARNING Fire Hazard

9/16” min. flat

Brace

Countertop thickness 1-1/2” min. is required to support the product. Countertop width 1-1/2” min. is required to properly support the 3/4” anti-tip screw. Braces must be installed between the underside of the countertop and the cabinet if required to obtain 1-1/2” minimum thickness (each side) Make sure the wall coverings, counters and cabinets around the oven can withstand the heat (up to 200°F [93.3°C]) generated by the oven.

This range is designed to hang from the counter top. It does not rest on the cabinet. The range must not be installed on a floor or sub structure (2” x 4” support)

13/32”

18” Min.

30” MIN.

* 21-3/4” CABINET FACE TO REAR OF CUT-OUT

TRIM SECTION FOR COUNTERTOP WITH POST FORMED OR RAISED FRONT EDGE

4” MAX.

28-1/2” • Allow 30” minimum clearance between surMIN. face units and bottom of unprotected wood 27” 28-7/16” or metal cabinet, or allow a 24” minimum BETWEEN CABINETS when bottom of wood or metal cabinet is JUNCTION BOX LOCATION (BOX MUST NOT EXTEND MORE THAN SURWHFWHGE\QROHVVWKDQµWKLFNÀDPH 3” OFF THE PLANE OF THE WALL) retardant millboard covered with not less MOULDING MAY BE FITTED TO than No 28 MSG sheet metal, (.015”), .015” THE OVEN TRIM FOR A MORE CUSTOM APPEARANCE thick stainless steel, .024” aluminium or .020” copper. • This appliance has been approved for 0” spacing to adjacent surfaces above the cooktop. However, a 6” minimum spacing to surfaces less than 15” above the cooktop and adjacent cabinet is recommended to reduce exposure to steam, grease splatter and heat. • 7RUHGXFHWKHULVNRIEXUQVRU¿UHZKHQUHDFKLQJRYHUKRWVXUIDFHHOHPHQWVFDELQHWVWRUDJHVSDFH above the cooktop should be avoided. If cabinet storage space is to be provided above the cooktop, the risk can be reduced by installing a range hood that projects at least 5” beyond the front of the cabinets. Cabinets installed above the cooktop must be no deeper than 16”. Locate a wiring junction box at the rear of the cutout. The dimension from the top of the wiring junction ER[WRWKHFRXQWHUWRSPXVWEHDPLQLPXPRIµ7KHER[PXVWQRWH[WHQGPRUHWKDWµRȺWKHSODQH of a wall. The junction box must be located where it will allow considerable slack in the range conduit, so that the range can be pulled for servicing if necessary.

7 CHECK FOR PROPER INSTALLATION OF ANTI-TIP SCREWS • Raise lift-up cooktop and support it with cooktop support rod so anti tip screws are visible. (see Section 6) • Lower the oven door and gently apply a medium force to the inside of the door at the handle end. • Properly installed screws will prevent any movement of the range when force is applied to the door. If movement occurs, refer to “Mounting the range in the opening” section.

8 WHEN INSTALLING RANGE IN COUNTERTOP WHICH IS CUT OUT If you have an existing 27” wide cutout that goes all the way to the wall, you may want to buy a backsplash kit for your range. Order Kit JX27RWH (White) or Kit JX27RBK (Black). This kit will fill in the space between the back of the range and the wall.

Cord Neutral terminal Ground plate (grounding to range)

BACKSPLASH KIT FOR 27” DROP-IN RANGES This kit contains: 1 Backsplash 2 Screws 1 Maintop Filler 2 Wood Screws

Backsplash with End Caps

NOTE: The backsplash attaches to the counter. The range slides into position after the backsplash is in place.

Filler Screw

,PSURSHUFRQQHFWLRQRIDOXPLQXPKRXVHZLULQJWRFRSSHUOHDGVFDQUHVXOWLQDQHOHFWULFDORU¿UHKD]DUG,I residence leads are aluminum, use only connectors designed for joining copper to aluminum and follow the manufacturer’s recommended procedure closely. Failure to do so may result in serious injury or death. :HUHFRPPHQG\RXKDYHWKHHOHFWULFDOZLULQJDQGKRRNXSRI\RXUDSSOLDQFHFRQQHFWHGE\DTXDOL¿HGHOHFWULFLDQ After installation, have the electrician show you how to disconnect power from the appliance.