conducteur autour de la vis de borne. Reserrer les vis de bornes. Couple de serrage: 1,0—1,4 Nom. AVISO: Para ser instalado por un electricista calificado. de acuerdo con los côdigos persona nacionales y locales. ADVERTENCIÆRIESGO DE CHOQUE. ELECTRICO O MUEH'I'E. Desconectar la corriente antes de la ...
Twist clockwise by hand in direction of arrow, locking between 30º and 180º. Disconnecting. 1. Twist counter clockwise by hand, until large arrows are aligned. 2. Pull devices apart. Replacement parts of HUBBELL®SINGLE POLE DEVICES. WARNING: Use only
circuits sharing a common compartment with communications, class 2, or class 3 ... communication ou de circuits de classe 2. .... masking tape (as illustration E.
Reinstall riser [2] aligning tabs with slots Secure using #8-32 pan head screws [1] in corners. Verify that concrete cover [5] is secure. Cover visible openings and ...
10 nov. 2012 - Seal the gap around the cover support collar [12] with a continuous .... Débrancher le circuit avant de procéder au montage ou à l'entretien.
power receptacle MUST be installed on this cable before using. 2. ... disconnect cable and have the fault corrected by a qualified electrician. ... Service Manual.
This feature does NOT isolate the power supplied to the enclosure during internal .... NOTE : “G” designates ground wire and yellow and green grounding buss.
Code, Part 1, Rule 28-602(3)(c)(i)]. 4. Suitable for use on a ... Install new switch and ¼” square drive shaft by pushing shaft to bottom of gear pocket, tighten set ...
8 sept. 2010 - Remove four #8-32 pan head screws [1] from top corners of floor box assembly and retain. Remove transition [2] and mounting plate [3] assemblies from box and retain. Install leveling screws [4] as shown in FIGURE A. Make conduit connec
Cut into a 1/8” (3.2mm) thick enclosure mounting surface a 29/32” (23.0 mm) ø ... Ne jamais câbler des composants électriques dans un circuit sous tension.
Don't pull lacing too tight. Leave a space between adjoining loops approximately equal to the width of one diamond of the mesh. (Fig. 2.2). 2.3. At the tail end of ...
appropiate wire gage based on local code requirements or de-rate device based on wire gage selected. WIRING INSTRUCTIONS ... 15 A tighten to 12-14 in-lbs (1.4 - 1.6 N•m). 20 A and 30 A tighten to 15-20 in-lbs. (1.7 - 2.3 N•m). SILVER SCREW – W – Neut
8 sept. 2010 - Remove four #8-32 pan head screws [1] from top corners of floor box assembly and retain. Remove transition [2] and mounting plate [3] ...
connections to the light fixture. Secure arm with light fixture using bracket and bolts provided. Fasten the reflector to the. fixture using two screws with washer. 5.
instructions. 2. CAUTION: RISK OF ELECTRIC SHOCK. More than one disconnect switch may be required to de‑energize this equipment before servicing. Disconnect ALL ... HBLDS3SSR series Type 4X and Type 12 Manual Motor Controller .... Utilice chorro de a
8 sept. 2010 - ATTENTION - RISQUE DE CHOC ÉLECTRIQUE. ... Utiliser le joint pour plancher fourni ou appliquer un cordon continu de 6,3 mm de pâte à ...
communications standards, the following instructions and any instructions included with ... For installations requiring more than 3 gangs, remove screws [1].
Restore power to the sensor and allow it to initialize (up to 2 minutes). 6.Sensor is ... Step back from the sensor to avoid changing ambient light levels in the room ...
Disconnect ALL power supplies to enclosure before exposing interior. 3. .... NOTE : “G” designates ground wire and yellow and green grounding buss. 30 A.