INSTRUCTIONS. D'INSTALLATION. Tuyau en laiton - embouts et mamelons pour boyau d'arrosage. 1.Appliquer de la pâte à joint ou un adhésif d'étanchéité. 2.
tubing. 1.Ajuster l'écrou et la gaine sur en la tuberia. 2. Cut tubing square. Insert le tube. 2. Corte la tuberia recta. Introduzca tubing into fitting. 2. Couper le tube à l'équerre. la tuberia en el empalme. 3. Hand-tighten plus 1/4 turn Insérer l
BC. Oo nlin e.co m. A Watts Water. Technologies Company. US. A: Tel. (8 ..... Remettre en place le couvercle en s'assurant que le dispositif à ressorts est placé.
ÉCROU 45 FLARE FIare Frttmg - For copper Raccord evase - pour tube Empalme con punta conrca -. RACCORD A 45° - - - - - ' ... ENSANCHAÛ° DE 45 only seulement aluminio solamente. 1. Fit nut on tubing. FIare 1. ... NUT AND SLEEVE fitting - for all tubin
Local codes typically require the use of a backflow preventer in the system. (Watts Model 9D). Consult local authorities for the type, installation and test- ing requirements. The backflow preventer must be installed upstream of the regulator. 3. Pri
If the downstream system pressure is higher than the set pressure under no flow conditions, the cause could be thermal expansion, pressure creep or dirt/debris on the seat. Thermal expansion occurs whenever water is heated in a closed system. The sys
the valve body pointing in the direction of flow to the boiler. ... as short as possible and be the same size as the SRV discharge connection throughout its entire length. .... equipment. Keep this Manual for future reference. Dial Set &. Fast-Fill.
sistema debido a ciertos requisitos de flujo de operación. Cuando se recibe la válvula, el control de ajuste está en la posición totalmente abierta. (La ranura.
do not us e an air ga p fi ttin g at fa ce le vel so as to prev ent pers on alin jury from sc aldi ng wate r or stea m.In no ev ent sh ould th e ve nt op enin g or drai n li ne be plug ge d. • If lo cal co de s re quir e th e de vice be te sted. , it
HEAT RAYS (INFRARED RADIATION) from flame or hot metal can injure eyes. 7. After soldering, flush piping and install valve using filter washer on hot and ...
To prolong the life of the Model LF1170-M2 or LFL1170-M2 valve, it is recommended that it be trapped as shown (Figure1): i.e. ... 1. Readjust valve temperature per installation instructions. Hot water from cold water tap or cold from hot. 1. Check va
Need for Periodic Inspection/Maintenance: This product must be tested periodically in compliance with local codes, but at least once per year or more as service ...
Ouvrir le dispositif de remplissage rapide de la soupape de remplissage ou de la soupape d'alimentation en eau de la chaudière. Laisser l'eau s'écouler par le ...
table device and can be tested at any time to ensure proper operation. .... manufacturers with your WDS, your specific mating connectors may not be included.
charge should match the system fill pressure. (water pressure regulator valve) setting. If replac- ing tank, remove old tank and install new tank. Check air charge in new tank and adjust if needed. Model RBFF. Modelo RBFF. Modèle RBFF. Residential Bo
“Quick-Connect Installation” instructions below. 4. Flush the lines to remove all loose scale, dirt and other foreign matter that can damage or clog the valve. 5.
Installation should be in accordance with acceptable plumbing prac- ... Open enough fixtures to meet the minimum flow requirement of the ..... Hot Water Return ... or consequential damages, including without limitation, lost profits or the cost of ..
Install the regulator with the arrow on the body pointing in the direction of the flow. 6. Regulator may be installed vertically or horizontally (upright or inverted). 7.
great salt-free alternative to water softening (ion exchange) ..... Any component failure must not result from abuse, fire, freezing or other acts of nature, violence, ...
