340906_Floor Box&Kit_IS.qxd:340906 IS - Legrand

2. Cut line voltage wires, leaving a minimum length of 9" above the opening of the box. 3. Low and line voltage cannot be installed in the same cavity per the.
105KB Größe 4 Downloads 59 vistas
®

TradeMaster

Floorbox and Tamper Resistant Finishing Kit Installation Instructions

Floorbox Description

TradeMaster® Tamper-Resistant Finishing Kit

The TM1542BOX for installation of electrical receptacles in wooden floors, where required by National Electrical Code Standards, or for aesthetic preference. The round floorbox is finished by a TM1542 finishing kit, (sold separately). Floorbox can also accommodate low voltage wires, through the compartments provided.

I. Cover installation Plastic Covers: TM1542TRBR, TM1542TRW, TM1542TRLA, TM1542TRGRY 1. Optional low voltage feed-through applications: (See Figure 4) a. Drill 3/8" diameter hole(s) in the cover. Drill hole locations are marked on the bottom side of the cover. b. Insert grommet(s) into the drilled holes and route the low voltage communication wire(s) through the grommet opening(s). 2. Insert the cover into TM1542-BOX opening. 3. Fasten the adapter to the box with the four screws provided. Do not tighten the screws to the point where the cover distorts (approx. 12 in-lbs). Brass Covers: TM1542TRFM, TM1542TRCF 1. Optional low voltage feed-through applications: (See Figure 4) a. Drill 3/8" diameter hole(s) in the brass flange. Drill hole locations are indented on the bottom side of the brass flange. b. Insert grommet(s) into the drilled holes and route the low voltage communication wire(s) through the grommet opening(s). 2. Insert the adapter into the center of the flange (only if separated from flange). 3. Fasten the adapter to the box with the four screws provided. Do not tighten the screws to the point where the adapter distorts (approx. 12 in-lbs). Note: TM1542TRFM cannot be used with finished floor thickness of less than 3/8".

Application Floorbox is used to provide a place for electrical power in the floor, in an application where it is difficult or impossible to provide power in the wall, but where it is required by the NEC. The box can also be used to provide electrical power where it is desired in the middle of the room, without the use of extension cords. The box can also be used to provide access to low voltage communication wires.

Tamper-Resistant Finishing Kit Description and Application The finishing kit is used to mount the electrical outlet in the TradeMaster® Floorbox, (sold separately). The plastic cover is available in four different colors to blend into your décor. The brass cover is available in two designs: A flush-mount version for hardwood floors, and a raised flange version for carpeting, linoleum, etc. the outlet is covered by a door which can be removed and replaced. When the outlet is not in use, the door shuts for a flush finish. These covers are designed to be used only with the TM1542BOX TradeMaster® Floorbox. A 15 Amp, 125 Volt Tamper-Resistant outlet is included with the finishing kit. This outlet meets NEC 406.11 requirment for Tamper-Resistant receptacles in dwellings. The kit can be used with any decorator style device, such as a GFCI, TVSS, or low voltage device. Low Voltage communication wires can also be installed outside of the line voltage area by drilling holes in the cover as described in these instructions.

Grommets

AVAILABLE CATALOG #’s Catalog #

Drill Hole Locations

Figure 4

Description

TM1542BOX

Round Wood Floorbox

TM1542TRBR

Brown Finishing Kit with Brown 15 Amp, 125 Volt Tamper-Resistant Outlet

TM1542TRW

White Finishing Kit with White 15 Amp, 125 Volt Tamper-Resistant Outlet

TM1542TRLA

Light Almond Finishing Kit with Light Almond 15 Amp, 125 Volt Tamper-Resistant Outlet

TM1542TRGRY

Gray/Paintable Finishing Kit with Gray 15 Amp, 125 Volt Tamper-Resistant Outlet

TM1542TRCF

Brass Finishing Kit, Carpet Flange with Brown 15 Amp, 125 Volt Tamper-Resistant Outlet

TM1542TRFM

Brass Finishing Kit, Flush Mount with Brown 15 Amp, 125 Volt Tamper-Resistant Outlet

II. Receptacle Installation Warning: Turn off all power to circuit before installing this device. Improper wiring of any electrical device can cause serious injury or death. These wiring devices should only be installed by an Electrician or other qualified person. Connect only copper or copper-clad wire to the device in this package. Do not connect aluminum wire to this device. Plastic Covers: TM1542TRBR, TM1542TRW, TM1542TRLA, TM1542TRGRY (See Figure 5) 1. If using the included outlet, strip conductors to 3/4". If using a different device, follow instructions on package. 2. Terminate Ground, Neutral, and Hot wires in that order. 3. Install (attach) outlet to the cover with the two screws provided. 4. Snap the decorator cover over the outlet face. 5. Replace the door if removed during installation with a snap fit at the hinge area.

Warning: Turn off all power to circuit before installing this device. Improper wiring of any electrical device can cause serious injury or death. These wiring devices should only be installed by an Electrician or other qualified person. Connect only copper or copper-clad wire to the device in this package. Do not connect aluminum wire to this device. Wiring and floorbox installation must comply with the National Electrical Code, and all applicable local codes. As with any floor box, leaving the door open while not in use may result in contamination of the installed wiring device, causing it to fail.

Door Decorator Cover Tamper-Resistant Receptacle Cover O Ring Adapter Flange

TradeMaster® TM1542-BOX I. Box Installation 1. Determine the box location 2. Cut a 4 3/4" diameter hole into the sub-floor 3. Secure the TM1542-BOX to the sub-floor with the three screws provided. (See Figure 1) 4. Lay finish floor over the sub-floor. The hole placed in the finish floor cannot exceed 6" in diameter. Larger hole will not be covered by the finishing kit. (See Figure 2) Finish floor (Opening must be less than 6" dia.)

Figure 5

Figure 6

Brass Covers: TM1542TRFM, TM1542TRCF (See Figure 6) 1. If using the included outlet, strip conductors to 3/4". If using a different device, follow instructions on the outlet package. 2. Terminate Ground, Neutral, and Hot wires in that order. 3. Install (attach) outlet to the cover with the two screws provided. 4. Snap the decorator cover over the outlet face. 5. Replace the door to the flange with the two screws provided.

Limited One Year Warranty Pass & Seymour will remedy any defect in workmanship or material in Pass & Seymourʼs products which may develop under proper and normal use within one year from date of purchase by a customer:

Sub floor Figure 1

Figure 2

II. Wire Installation 1. Pull the line voltage conductors through the boxʼs auto clamp openings or the knockout openings located near the bottom of the box. If knockouts are used, wire clamps are required (not supplied). 2. Cut line voltage wires, leaving a minimum length of 9" above the opening of the box. 3. Low and line voltage cannot be installed in the same cavity per the National Electrical Code. (See Figure 3)

(1) by repair or replacement, or, at Pass & Seymourʼs option, (2) by return of an amount equal to consumerʼs purchase price. Such remedy is IN LIEU OF ANY AND ALL EXPRESSED OR IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Such remedy by Pass & Seymour does not include or cover cost of labor for removal or reinstallation of the product. ALL OTHER FURTHER ELEMENTS OF DAMAGE (INCIDENTAL OR CONSEQUENTIAL DAMAGES) FOR BREACH OF ANY AND ALL EXPRESSED OR IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE EXCLUDED HEREBY. (Some states do not allow disclaimer or exclusion or limitation of incidental or consequential damages, so the above disclaimers and limitation or exclusion may not apply to you. ANY IMPLIED WARRANTIES INCLUDING WHERE REQUIRED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED TO THE ONE YEAR PERIOD SET FORTH ABOVE. (Some states do not allow limitations on how long implied warranty lasts, so the above limitation may not apply to you.) To insure safety, all repairs to Pass & Seymour products must be made by Pass & Seymour, or under specific direction. Procedure to obtain performance of any warranty obligation is as follows: (1) Contact Pass & Seymour, Syracuse, NY 13221, for instructions concerning return or repair; (2) return the product to Pass & Seymour, postage paid, with your name and address and a written description of the installation or use of the Pass & Seymour product, and the observed defects or failure to operate, or other claimed basis for dissatisfaction.

Low Voltage Line Voltage ©2010 Pass & Seymour/Legrand P.O. Box 4822, Syracuse, NY 13221 P/N 340906

Figure 3

®

TradeMaster

Caja de Piso y Juego de Últimos Toques Resistente a la Manipulación Indebida Instrucciones de Instalación

Descripción de Caja de Piso El TM1542BOX para instalación de enchufes eléctricos en pisos de madera, donde es requerido por los estándares del Código Eléctrico Nacional o por preferencia estética. La caja de piso redonda se termina con el juego de últimos toques TM1542 (vendido por separado). Caja de Piso también puede acomodar cables de bajo voltaje, a través de los compartimientos proveídos.

Aplicación Caja de Piso se utiliza para proveer un lugar con electricidad en el piso, en una aplicación donde es difícil o imposible proveer electricidad en la pared pero donde es requerida por el NEC. La caja también se puede utilizar para proveer electricidad donde se desee en el medio de un cuarto, sin una extensión. La caja también se puede utilizar para proveer acceso a cableado de comunicación de bajo voltaje.

Descripcion y Aplicacion del Juego de Últimos Toques Resistente a la Manipulación Indebida El juego de terminación se utiliza para montar el enchufe eléctrico en la Caja de Piso TradeMaster® (vendida separadamente). La tapa de plástico está disponible en cuatro colores diferentes para lucir mejor en su ambiente de uso. La tapa de latón está disponible con dos diseños: versión de montaje al ras para pisos de madera y versión con alas para alfombras, linóleo, etc. El enchufe esta cubierto por una puerta que puede ser quitada y reemplazada. Cuando el enchufe no se está usando, la puerta cierra para una terminación en línea. Estas tapas están diseñadas para ser usadas solamente con la caja de piso TradeMaster® TM1542BOX. Con el kit de acabado, se incluye un tomacorriente resistente a la manipulación indebida de 15 Amperios, 125 Voltios. Este tomacorriente cumple la norma NEC 406.11 para tomacorrientes resistentes a la manipulación indebida en casas. El kit puede utilizarse con cualquier dispositivo estilo decorativo, tal como GFCI, supresores de sobrevoltajes transitorios (TVSS) o dispositivos de bajo voltaje. También pueden instalarse alambres de comunicación de bajo voltaje por fuera del área de voltaje de línea taladrando orificios en la cubierta tal como se describe en estas instrucciones.

TradeMaster® Juego de Últimos Toques Resistente a la Manipulación Indebida I. Instalación de Tapa Tapas de Plástico: TM1542TRBR, TM1542TRW, TM1542TRLA, TM1542TRGRY 1. Aplicaciones de bajo voltaje de pase Opcionales (Véase la Figura 4) a. Taladre hueco(s) de 3/8" de diámetro en la tapa. Marcas para taladrar los huecos están en la parte de abajo de la tapa. b. Inserte la(s) arandela(s) de cabo en los huecos taladrados y meta los cables de bajo voltaje por los huecos de la(s) arandela(s). 2. Ponga la tapa en la apertura del TM1542-BOX. 3. Fije la tapa a la caja con los cuatro tornillos proveídos. No apriete los tornillos tanto que distornsionen el adaptador (aproximadamente 12 in-lbs). Tapas de Latón: TM1542TRFM, TM1542TRCF 1. Aplicaciones opcionales de bajo voltaje y con continuacion: (Vease la Figura 4) a. Taladre hueco(s) de 3/8" de diametro en el ala de latón. La localización de los huecos están indentados en la parte de abajo del ala de latón. b. Inserte la(s) arandela(s) de cabo en los huecos taladrados y encamine lo(s) cable(s) de comunicaciones de bajo voltaje a través de la(s) apertura(s) en las arandela(s). 2. Inserte el adaptador en el centro de la arandela de cabo (solo si separado del ala). 3. Asegure el adaptador a la caja con los cuatro tornillos proveidos. No apriete los tornillos tanto que distornsionen el adapta dor (aproximadamente 12 in-lbs). Nota: TM1542TRFM no puede ser usado con pisos terminados con grueso de menos de 3/8". Arandelas de Cabo

NUMEROS DE CATÁLOGOS DISPONIBLES N° de Catalogo

Descripción

TM1542BOX TM1542TRBR

Caja redonda para piso de madera

TM1542TRW

Kit de acabado color blanco con tomacorriente resistente a la manipulación indebida color blanco, 15 Amperios, 125 Voltios

TM1542TRLA

Kit de acabado color almendra claro con tomacorriente resistente a la manipulación indebida color almendra claro, 15 Amperios, 125 Voltios

TM1542TRGRY

Kit de acabado color gris/pintable con tomacorriente resistente a la manipulación indebida color gris, 15 Amperios,125 Voltios

TM1542TRCF

Kit de acabado color dorado, reborde para alfombra, con tomacorriente resistente a la manipulación indebida color café, 15 Amperios, 125 Voltios

TM1542TRFM

Kit de acabado color dorado, montaje al ras, con tomacorriente resistente a la manipulación indebida color café, 15 Amperios, 125 Voltios

Localización de Huecos

Figura 4

Kit de acabado color café con tomacorriente resistente a la manipulación indebida color café, 15 Amperios,125 Voltios

Advertencia: Apague todos los circuitos antes de instalar este aparato. Un alambrado incorrecto de cualquier aparato eléctrico puede causar daños serios o muertes. Estos aparatos debían instalarse solamente por un electricista u otra persona calificada. Conecte únicamente cables de cobre o revestidos de cobre al aparato en este paquete. No conecte cables de aluminio a este aparato. Cableado e instalación de la caja de piso tiene que cumplir con el Código Eléctrico Nacional y todos los códigos locales aplicables. Como con cualquier caja de piso, el dejar la puerta abierta mientras no se esté usando resultará en contaminación del dispositivo eléctrico instalado, causándole fallas.

TradeMaster® TM1542-BOX I. Instalación de la Caja 1. Determine la localización de la caja. 2. Corte un hueco de 4 3/4" de diámetro en el sub-piso. 3. Asegure el TM1542-BOX al sub-piso con los tres tornillos proveídos. (Véase la Figura 1) 4. Ponga el piso terminado sobre el sub-piso. El hueco hecho en el piso terminado no puede pasarse de 6" de diámetro. Huecos mas grandes no serán cubiertos por el juego de Ultimos Toques. (Véase la Figura 2) Piso Terminado (Hueco debe ser menos de 6" dia.)

Sub Piso Figura 1

Figura 2

II. Instalación de Cables 1. Hale los conductores de voltaje de línea a través del las aperturas de grámpas automáticas o los discos removibles en la parte de abajo de la caja. Si los huecos de destapaderos se utilizan, grapas de cable son requeridas (no suministradas). 2. Corte los cables de voltaje de línea, dejando un largo de 9" por en cima de la apertura de la caja. 3. Bajo voltaje y voltaje de línea no puede instalarse en la misma cavidad de acuerdo con el Código Eléctrico Nacional. (Véase la Figura 3)

de Bajo Voltaje Voltaje de Línea Figure 3

II. Instalación de Enchufe Advertencia: Apague todos los circuitos antes de instalar este aparato. El alambrado incorrecto de cualquier aparato eléctrico puede causar daños serios o muertes. Estos aparatos debían instalarse solamente por un electricista u otra persona calificada. Conecte únicamente cables de cobre o revestidos de cobre al aparato en este paquete. No conecte cables de aluminio a este aparato. Tapas de Plástico: TM1542TRBR, TM1542TRW, TM1542TRLA, TM1542TRGRY (Véase la Figura 5) 1. Si utiliza el enchufe incluido, pele los conductores 3/4". Si utiliza un dispositivo diferente, siga las instrucciones en el paquete. 2. Conecte la Tierra, Neutral y Cargado en ese orden. 3. Instale (fije) el enchufe a la tapa con los dos tornillos proveídos. 4. Enganche la tapa decoradora sobre el frente del enchufe. 5. Reemplace la puerta si se quitó durante la instalación con una entrada de resorte en la parte de la visagra. Puerta Tapa Decoradora Tomacorriente de una salida resistente a la manipulación indebida

Tapa Junta Adaptador Ala

Figure 5

Figure 6

Tapas de Latón: TM1542TRFM, TM1542TRCF (Véase la Figura 6) 1. Si utiliza el enchufe incluido, pele los conductores a 3/4". Si utiliza otro dispositivo, siga las instrucciones en la caja del enchufe. 2. Conecte la Tierra, Neutral y Cargado en ese orden. 3. Instale (ponga) el enchufe en la caja con los dos tornillos proveidos. 4. Apriete hasta que tranque, la tapa decoradora, sobre la parte de alante del enchufe. 5. Ponga la tapa en el ala con los dos tornillos proveidos.

Garantía Limitada De Un Año Pass & Seymour remediara cualquier defecto en la manufactura o material de productos Pass & Seymour que ocurran durante un apropiado y normal uso, dentro de un ano de la fecha de la compra por un cliente: (1) por reparación o reemplazo o, según opción de Pass & Seymour, (2) por devolución de una cantidad igual al precio de compra por el consumidor. Tal remedio es EN LUGAR DE CUALQUIERA Y TODAS LAS GARANTIAS EXPRESADAS O IMPLICITAS DE LA MERCANTIBILIDAD O USO APROPIADO A UN PROPOSITO PARTICULAR. Tal remedio por Pass & Seymour no incluye o cubre el costo de mano de obra por la remoción o reinstalación del producto. TODOS LOS DEMAS ELEMENTOS (INCIDENTALES O CONSECUENTES) DE DANO POR INCUMPLIMIENTO DE CUALQUIER Y TODAS LAS GARANTIAS EXPRESAS O IMPLICITAS INCLUYENDO GARANTIAS DE MERCANTIBILIDAD O USO APROPIADO A UN PROPOSITO PARTICULAR ESTAN POR TANTO EXCLUIDAS. (En algunos estados este acápite excluyente o limitante de danos incidentales o consecuentes no es permitido, así que los excluyentes y limitantes arriba mencionados pueden no ser aplicables a Ud.) CUALQUIER GARANTIA IMPLICITA INCLUYENDO LAS REQUERIDAS PARA MERCANTIBILIDAD O USO APROPIADO PARA UN PROPOSITO PARTICULAR SERAN LIMITADAS AL PERIODO DE UN ANO ARRIBA EXPRESADO. (Algunos estados no permiten limitaciones sobre la longitud la garantía implícita durara, por tanto la limitación arriba expresada podrá no ser aplicable a Ud.). Para asegurar la seguridad, todas las reparaciones a los productos Pass & Seymour deben ser hechas por Pass & Seymour, o bajo su especifica dirección. El procedimiento para obtener cumplimiento de cualquier obligación de la garantía es tal y como sigue: (1) Contacte Pass & Seymour, Syracuse, New York 13221, para instrucciones concernientes a la devolución o reparación; (2) devuelva el producto a Pass & Seymour, con el franqueo pagado, con su nombre y dirección y una descripción escrita de la instalación o el uso del producto Pass & Seymour, y de los defectos observados o las fallas de operación, u otra base para reclamar su insatisfacción.